ECO mode INFINITI QX60 HYBRID 2014 Quick Reference Guide

essential information
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator
A Tire Pressure Low - Add Air warning message will
appear in the vehicle information display
01 and the
low tire pressure warning light 02 will illuminate when
one or more tires are low on pressure and air is needed.
• The tire pressures should be checked when the
tires are cold. The tires are considered cold after
the vehicle has been parked for 3 hours or more or
driven less than 1 mi (1.6 km) at moderate speeds.

When adding air to an under-inflated tire, the TPMS
with Tire Inflation Indicator provides visual and audible signals to hel\
p you inflate the tires
to the recommended COLD tire pressure.
To use the tire inflation indicator:
1. Move the shift lever to the P (PARK) position and apply the parking brake.
2. Place the ignition switch in the ON position. Do not start the engine.
3. Add air to the under-inflated tire and within a few seconds, the hazard \
warning lights will
start flashing.
4. When the designated tire pressure is reached, the horn will beep once an\
d the hazard
warning flashers will stop flashing.
5. Repeat this procedure for any additional under-inflated tires.

After tire pressures are adjusted, drive the vehicle at speeds above 16 \
MPH (25 km/h).
The Tire Pressure Low - Add Air warning message and low tire pressure warning light
will disappear.
Hybrid Awareness
Your vehicle is virtually silent in the electric mode. If you exit your \
vehicle while it is ON,
but the engine is not running, the engine will automatically start, info\
rming you that the
car is still ON.

Do not store your INFINITI Intelligent Key within detection range of the\
vehicle. This may
cause welcome lights and other functions to activate creating unwanted b\
attery drain.

The hybrid system is designed for optimum efficiency and performance. Ac\
tivation of the
electric mode may vary with driving conditions and driver input. A full \
battery display does
not indicate the vehicle should be in the electric mode.
For more information, refer to the “Hybrid System Overview” section of your Owner’s Manual.
Hybrid System Warning Light
This light will illuminate when the ignition switch is in
the ON position and will turn off when the hybrid
system is started.

The light will also illuminate when a malfunction occurs in the electric\
motor or hybrid system.

When this light illuminates while driving, immediately stop the vehicle \
in a safe location
and contact an INFINITI retailer.

If the hybrid system warning light blinks while driving, it may indicate\
that the Li-ion
battery charge is low and you cannot continue to drive.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
01
7
02
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 79/24/13 11:43 AM

10
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or unlock your
vehicle, open your liftgate and remotely start the engine. It is importa\
nt to
make sure the Intelligent Key is with you (that is, in your pocket or p\
urse).
REMOTE ENGINE START* (if so equipped)

The remote engine start system must be enabled in the vehicle
settings within the vehicle information display.

The remote engine start operating range is approximately 200 ft
(60 m) from the vehicle. The effective operating range may be
shorter due to environmental conditions or obstacles between you
and the vehicle.

For the remote engine start to function, the vehicle must be in the
P (PARK) position with the ignition off, and all the doors closed
and locked.

To start your vehicle remotely:
1. Press the

button
01.
2. Within 5 seconds press and hold the remote
engine start

button
02 for at least 2 seconds.

The engine will start and the parking lights will turn on.

Automatic climate control will begin heating or
cooling the vehicle depending on the last used mode.

The engine will run for 10 minutes and then turn off.

Repeat steps 1 and 2 to extend the time for an additional 10 minute peri\
od.
• After two remote starts the ignition switch must be cycled before the re\
mote
start can be
used again.

To start driving depress the brake pedal and push the ignition switch
START/STOP button.
LOCKING AND UNLOCKING THE VEHICLE

The lock and unlock operating range of the Intelligent Key is within 31.\
5 in (80 cm) from
each request switch.

To lock the vehicle, push either door handle request switch
03 once or press the
button
01 on the key fob.
To unlock the vehicle, perform one of the following procedures:
• Push either door handle request switch

03 once; the corresponding door will unlock. Push
the door handle request switch again within 30 seconds; all other doors will unlock, or
• Press the

button
04 on the key fob to unlock the driver’s side door. Press the

button again; all other doors will unlock.
LIFTGATE RELEASE

To open the rear liftgate, press the
button
05 for longer than 1 second.
To close the rear liftgate, press the
button
05 again for longer than 1 second.
PANIC ALARM

The Intelligent Key can also be used to activate the panic alarm by pres\
sing and holding
the
button
06 for more than 1 second. Once activated, the panic alarm and headlights
will stay on for a period of time.
first drive features
02
01
04
05
06
03
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 109/24/13 11:43 AM

first drive features
18
07 FAN SPEED CONTROL BUTTONS


Press the left button to decrease the fan speed or press the right
button to
increase the fan speed.
08 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS


Press the defroster control button
to turn the system on. The A/C automatically turns
on when the defroster mode is selected. This feature removes humidity fr\
om the air.


To defrost the front and side windows, set the temperature controls
03 and fan
speed controls 07 to their maximum settings.
09
DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS

Push the rear window defroster switch
REAR to turn the system on or off.
This function automatically turns off after approximately 15 minutes.
10 REAR AIR CONDITIONER


To control the rear automatic air conditioning
system with the front air conditioner control
panel, press the REAR button.


When the rear automatic air conditioning system
is on, the indicator light on the REAR button will
illuminate and the front display will switch to the
rear air conditioner screen. Use the driver
temperature and fan speed buttons to adjust settings.

To adjust the front air conditioning system, press the REAR button again.

To turn off the rear automatic air conditioning system from the front co\
ntrols, press the
REAR button until the Rear Air-conditioning screen is displayed. Then, press the
OFF button
12.

The rear passenger controls are unavailable when Rear Air-conditioning screen is
shown on the front display.
11 INTAKE AIR CONTROL BUTTON


Press the intake air control button to recirculate interior air inside the vehicle. The
indicator light on the button will illuminate. This system is used to a\
void certain
outside odors and helps to adjust the inside vehicle temperature more ef\
fectively.


The air recirculation mode cannot be activated when the climate control \
system is in the
front defrost mode

or front defrost and foot vent mode
.


Press the intake air control button again to change the air circulation from the
intake air to the outside air. The
indicator light on the button will turn off.
12 OFF BUTTON


Press the OFF button to turn the climate control system off.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4\
) ” of your
Owner’s Manual.
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 189/24/13 11:43 AM

21
Intelligent Cruise Control (ICC) System (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE

To set Vehicle-To-Vehicle Distance Control mode,
press the CRUISE ON/OFF button
01 for less than
1.5 seconds. The CRUISE indicator light 02
will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch
03 and
release it. Cruise control will be set to the
desired speed.

Press the distance button 04 repeatedly to change
the set distance between long, middle, and short.

When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed
indicator lights will illuminate

05 in set mode.

When a vehicle is detected ahead of you in the lane,
the vehicle ahead detection, set distance, and set vehicle speed
indicator lights will illuminate
06 in set mode.

To reset at a faster cruising speed, push and hold the ACCEL/RES
switch

07. When the vehicle attains the desired speed, release the switch.

To reset at a slower cruising speed, push and hold the COAST/SET switch


03. Release the switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
08 or tap the brake pedal. The set
vehicle speed indicator
05 will go out.

To turn off cruise control, press the CRUISE ON/OFF button
01. The CRUISE indicator light


02, in the instrument panel, will turn off.
To set conventional (fixed speed) cruise control mode:

While cruise control is off, press the CRUISE ON/OFF
button 01
and hold it down for more
than 1.5 seconds. The CRUISE indicator light will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch and release it. The SET indicator light will illuminate.
Cruise control will be set to the desired speed.
To switch between the two cruise control modes:

When one of the two cruise modes is in use, you must turn the system off,\
and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
01
0403
0708
0205
06
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 219/24/13 11:43 AM

Vehicle Information Display
The vehicle information display 01 displays
such items as:

Vehicle settings

Trip computer information

Energy flow meter

Drive system warnings and settings (if so equipped)

Cruise Control System

Intelligent Cruise Control (ICC) System
(if so equipped) information

Intelligent Key operation information

Indicators and warnings

Tire pressure information
USING THE VEHICLE INFORMATION DISPLAy
The vehicle information display modes can be changed
using the
button
02 and ENTER button 03
located
on the steering wheel.
1. Press
02 to enter the vehicle information menu items.
2. Press

04 to navigate through the items in vehicle information.
4. Press ENTER

03 to change or select an item in the vehicle information display.
5. Press
05 to go back to the previous menu.
START UP DISPLAy
When the vehicle is placed in the ON or ACC position the screens that display in the vehicle
information include:

Active system status (if so equipped)

Trip computer

Tire pressure information

Fuel economy

Warnings (displays when a warning is present)
RESETTING THE TRIP COMPUTER
1. Press the
button
02 until you reach the Trip
computer mode 06.
2.
Press the
button 02 again for more than 1.5
seconds to reset average fuel consumption, average
speed, distance to empty and journey time.
01
23
system guide
03
02
04
05
06
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 239/24/13 11:43 AM

system guide
24
Bluetooth® Hands-free Phone System
A cellular telephone should not be used while
driving so full attention may be given to
vehicle operation.*
SySTEM OPERATING TIPS

Press the or button to interrupt the voice
prompts at any time and speak a command after
the tone.

The “Help” command can be used to hear a list of
available commands at any time.

Reduce background noise as much as possible by
closing windows and pointing HVAC vents away from
the ceiling.

Speak naturally without long pauses and without
raising your voice.

When speaking Phonebook names, please be
aware some phones require the last name to be
spoken before the first name. For example,
“Michael Smith” may be spoken as “Smith Michael”.

To cancel a voice recognition session, say “Cancel” or
“Quit” or press and hold the

or
button for 5 seconds.

To go back to the previous command, say “Go back” or “Correctio\
n”.

If the Voice Recognition system does not recognize your voice commands, \
train the system
using the Speaker Adaptation Mode. See your Owner’s Manual for detail\
ed information.

For more detailed information and instructions, refer to your cellular p\
hone
Owner’s Manual and visit ww.InfinitiUSA.com/bluetooth.
*Some jurisdictions prohibit the use of cellular telephones while drivin\
g.
Bluetooth® Controls
Microphone
SETTINGS
The setting mode allows you to change the information displayed in the v\
ehicle
information display:

Driver Assistance (if so equipped)

Vehicle settings

Main Menu Selection

Body Color

Maintenance

Alarms

Language

Unit

Welcome Effects

Factory Reset
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 249/24/13 11:43 AM

25
Bluetooth® System without Navigation (if so equipped)
CONNECTING PROCEDURE
1. Press the
button on the steering wheel. The
system announces the available commands.
2. Say “Connect Phone”. The system acknowledges
the command and announces the next set of
available commands.
3. Say “Add Phone”. The system acknowledges
the command and asks you to initiate
connecting from the phone handset.
4. Initiate connecting from the phone.
• The connecting procedure varies according
to each cellular phone model. For detailed connecting instructions and a\
list of
compatible phones, please visit www.InfinitiUSA.com/bluetooth.
• When prompted for a PIN code, enter “1234” from the handset. (The\
PIN code is
assigned by INFINITI and cannot be changed.)
5. Say the name of the phone when the system asks you to provide one. you can give the
phone a name of your choice.
PHONEBOOK

Depending on the phone, the system may automatically download the entire phonebook.
For more information, please visit www.InfinitiUSA.com/bluetooth or the phone’s
user guide.

If the phonebook does not download automatically, 40 entries can be
individually downloaded.

To manually download entries:
1. Push the
button on the steering wheel.
2. After the tone, say “Phonebook”.
3. After the next tone, say “Transfer Entry”.
4. Using the phone, select an entry to send to the vehicle. Please consult t\
he website
above or your phone’s User Guide for specific steps of the phone.
5. The system will speak the transferred entry. Confirm the entry by saying\
“yes” after the tone.
MAKING A CALL By PHONEBOOK ENTRy

In some cases, names stored using all UPPERCASE letters may not be recognized by the
voice recognition system.
1. Press the
button.
2. After waiting for the tone, say “Call”.
3. After the next tone, speak a name of a phonebook entry. For example “\
Michael Smith”.
4. Confirm the correct name is recognized by saying “Dial” after the \
tone.
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 259/24/13 11:43 AM

system guide
30
Theater Package (if so equipped)
With this Entertainment System, you can play video
files via a DVD or CD providing images and sound
both from the front and rear display screens.

you can also connect auxiliary devices such as video
games, camcorders or portable video players to the
auxiliary jacks

01 located on the back of the center
console. (your device will be controlled through its
own control panel.)

Rear Auxiliary Mode allows rear seat passengers to
independently display different sources on
each screen.

Use the remote controller
02, provided with the
system, to operate the rear display screens.

Use the headphones
03, also provided with
the system, to listen to audio wirelessly and
independently. you may also connect your own
wired-headphones to the headphone jacks
04
located on the back of the center console.

For optimum performance, select the appropriate
headphone channel

05 that corresponds to the
headrest display being viewed directly in front of you.

To watch or control videos on the front display make
sure the vehicle is in the P (PARK) position and the
parking brake is applied.

To reduce driver distraction, the wireless headphones will not
operate while located in the front seats and movies will not be
shown on the front display while the vehicle is in any drive position.

To access standard DVD controls on the front display while playing
a DVD on the rear display, press the DISC•AUX button on the audio
control panel while the vehicle is in the P (PARK) position and the
parking brake is applied.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
09 – Press to switch between the day screen (bright) and the night sc\
reen (dark). Press
and hold the button to turn the display off. Press again to turn the dis\
play on.
10 BACK – Press to return to the previous screen. In a settings screen, this\
button can also
be used to apply the setting. In a character input screen, this button c\
an also delete the
characters that have been entered.
11 VOICE – Press to hear the current voice guidance for a programmed route.
For more information, please refer to your Navigation System Owner’s \
Manual.
05
04
01
02
03
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 309/24/13 11:44 AM