ignition INFINITI QX60 HYBRID 2014 Quick Reference Guide

4
new system features
When the shift lever is in the R (REVERSE) position and the CAMERA button 01 is pressed,
the following views will display in order:
Start from any Control Panel screen
Press
Press
Press
Press
Around View® Monitor (AVM) with Moving Object Detection (MOD)
(if so equipped)
With the ignition switch in the ON position, the
Around View Monitor is activated by pressing the
CAMERA button

01, located on the control panel, or
by moving the shift lever to the R (REVERSE) position.
The control panel displays various views of the
position of the vehicle.

When the shift lever is in the P (PARK), N (NEUTRAL)
or D (DRIVE) position and the CAMERA button

01 is
pressed, the following views will display in order:
01
Rear view & bird’s-eye view
Press
PressPress Rear view & front-side view
Rear wide view
Front wide view Front view & bird’s-eye viewFront view & front-side view
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 49/24/13 11:43 AM

essential information
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator
A Tire Pressure Low - Add Air warning message will
appear in the vehicle information display
01 and the
low tire pressure warning light 02 will illuminate when
one or more tires are low on pressure and air is needed.
• The tire pressures should be checked when the
tires are cold. The tires are considered cold after
the vehicle has been parked for 3 hours or more or
driven less than 1 mi (1.6 km) at moderate speeds.

When adding air to an under-inflated tire, the TPMS
with Tire Inflation Indicator provides visual and audible signals to hel\
p you inflate the tires
to the recommended COLD tire pressure.
To use the tire inflation indicator:
1. Move the shift lever to the P (PARK) position and apply the parking brake.
2. Place the ignition switch in the ON position. Do not start the engine.
3. Add air to the under-inflated tire and within a few seconds, the hazard \
warning lights will
start flashing.
4. When the designated tire pressure is reached, the horn will beep once an\
d the hazard
warning flashers will stop flashing.
5. Repeat this procedure for any additional under-inflated tires.

After tire pressures are adjusted, drive the vehicle at speeds above 16 \
MPH (25 km/h).
The Tire Pressure Low - Add Air warning message and low tire pressure warning light
will disappear.
Hybrid Awareness
Your vehicle is virtually silent in the electric mode. If you exit your \
vehicle while it is ON,
but the engine is not running, the engine will automatically start, info\
rming you that the
car is still ON.

Do not store your INFINITI Intelligent Key within detection range of the\
vehicle. This may
cause welcome lights and other functions to activate creating unwanted b\
attery drain.

The hybrid system is designed for optimum efficiency and performance. Ac\
tivation of the
electric mode may vary with driving conditions and driver input. A full \
battery display does
not indicate the vehicle should be in the electric mode.
For more information, refer to the “Hybrid System Overview” section of your Owner’s Manual.
Hybrid System Warning Light
This light will illuminate when the ignition switch is in
the ON position and will turn off when the hybrid
system is started.

The light will also illuminate when a malfunction occurs in the electric\
motor or hybrid system.

When this light illuminates while driving, immediately stop the vehicle \
in a safe location
and contact an INFINITI retailer.

If the hybrid system warning light blinks while driving, it may indicate\
that the Li-ion
battery charge is low and you cannot continue to drive.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
01
7
02
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 79/24/13 11:43 AM

10
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or unlock your
vehicle, open your liftgate and remotely start the engine. It is importa\
nt to
make sure the Intelligent Key is with you (that is, in your pocket or p\
urse).
REMOTE ENGINE START* (if so equipped)

The remote engine start system must be enabled in the vehicle
settings within the vehicle information display.

The remote engine start operating range is approximately 200 ft
(60 m) from the vehicle. The effective operating range may be
shorter due to environmental conditions or obstacles between you
and the vehicle.

For the remote engine start to function, the vehicle must be in the
P (PARK) position with the ignition off, and all the doors closed
and locked.

To start your vehicle remotely:
1. Press the

button
01.
2. Within 5 seconds press and hold the remote
engine start

button
02 for at least 2 seconds.

The engine will start and the parking lights will turn on.

Automatic climate control will begin heating or
cooling the vehicle depending on the last used mode.

The engine will run for 10 minutes and then turn off.

Repeat steps 1 and 2 to extend the time for an additional 10 minute peri\
od.
• After two remote starts the ignition switch must be cycled before the re\
mote
start can be
used again.

To start driving depress the brake pedal and push the ignition switch
START/STOP button.
LOCKING AND UNLOCKING THE VEHICLE

The lock and unlock operating range of the Intelligent Key is within 31.\
5 in (80 cm) from
each request switch.

To lock the vehicle, push either door handle request switch
03 once or press the
button
01 on the key fob.
To unlock the vehicle, perform one of the following procedures:
• Push either door handle request switch

03 once; the corresponding door will unlock. Push
the door handle request switch again within 30 seconds; all other doors will unlock, or
• Press the

button
04 on the key fob to unlock the driver’s side door. Press the

button again; all other doors will unlock.
LIFTGATE RELEASE

To open the rear liftgate, press the
button
05 for longer than 1 second.
To close the rear liftgate, press the
button
05 again for longer than 1 second.
PANIC ALARM

The Intelligent Key can also be used to activate the panic alarm by pres\
sing and holding
the
button
06 for more than 1 second. Once activated, the panic alarm and headlights
will stay on for a period of time.
first drive features
02
01
04
05
06
03
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 109/24/13 11:43 AM

INTELLIGENT KEy BATTERy DISCHARGE

If the battery of the Intelligent Key is discharged,
or environmental conditions interfere with the
Intelligent Key operation, start the engine according
to the following procedure:
1. Move the shift lever to the P (PARK) position.
2. Firmly apply the foot brake.
3. Touch the ignition switch with the Intelligent Key
and a chime will sound.
4. Within 10 seconds after the chime sounds, push the ignition switch while depressing
the brake pedal and the engine will start.
*Laws in some communities may restrict the use of remote starters. Check\
local regulations before using this feature.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and
the “Maintenance and do-it yourself (section 8)” of your Owner’s Manual.
11
Power Liftgate

When the liftgate is closed and locked, the liftgate
will open automatically by:
• Pushing the power liftgate switch

01 on the
instrument panel.
• Pushing the liftgate opener switch

02, the
liftgate must be unlocked, or you must have the
Intelligent Key with you (in your pocket or purse).
• Pressing the

button
03 on the INFINITI
Intelligent Key for more than 1 second.

The power liftgate operation can be turned on or
off by the power liftgate main switch

04 on the
instrument panel.

•
When the power liftgate main
switch is pushed to the OFF
position, power operation is not
available using the power liftgate
switch on the liftgate

05 or the
liftgate opener switch 02.
For more information, refer to the “Pre-driving checks
and adjustments (section 3)” of your Owner’s Manual.
0401
02
0503
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 119/24/13 11:43 AM

13
3RD Row Manual Reclining Seatback
To recline the seatback, pull up on the latch
01
located on the outside corner of each seatback.
Lean back until the desired angle is obtained.

To bring the seatback forward again, pull up on the
latch

01 and move your body forward. The
seatback will move forward.
For more information, refer to the “Safety —— seats, seat belts and
supplemental restraint system (section 1)” of your Owner’s Manual.
Automatic Drive Positioner (if so equipped)
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner
01 memory.

Follow these procedures to set the memory positions:
• Confirm the shift lever is in the P (PARK) position.
• Push the ignition switch to the ON position.
•
Adjust the driver’s seat, steering column and
outside mirrors to the desired positions using the
adjusting switches for each feature.
• Push the SET switch and within 5 seconds, push the memory switch (1 or 2) for at least 1 second.
• The indicator light on the memory switch you select will illuminate for \
approximately
5 seconds, and a chime will sound (if so equipped) when memory is stor\
ed correctly.
• The driver’s seat, steering column and outside mirror positions are n\
ow set to your preference.

These memorized positions can also be linked to your INFINITI Intelligen\
t Key.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Outside Mirror Control Switch
To select the right or left side mirror, move the
control switch

01 right or left.

Adjust each mirror to the desired position using the
switch

02.

To fold the outside rearview mirrors, push the
switch
03 to the
position. To unfold the
outside rearview mirrors, push the switch

03 to
the

position.
02
01
03
01
01
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 139/24/13 11:43 AM

first drive features
14REVERSE TILT-DOWN FEATURE (if so equipped)


The reverse tilt-down feature will turn the selected outside mirror surf\
ace downward to
provide better rear visibility close to the vehicle.
1. Push the ignition switch to the ON position.
2. Choose the right or left outside mirror by operating the outside mirror \
control switch
01.
3. Move the shift lever to the R (REVERSE) position.
4. The outside mirror surfaces move downward.

The outside mirror surfaces will return to their original positions when\
one of the following
conditions has occurred:
• The shift lever is moved to any position other than R (REVERSE).
• The outside mirror control switch is set to the center (neutral) posit\
ion.
• The ignition switch is pushed to the OFF position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Starting/Stopping the Hybrid System
It is important to make sure the INFINITI Intelligent
Key is with you (that is, in your pocket or purse).

Depress the brake pedal.

Press the ignition switch START/STOP button to
start the hybrid system.
TURNING THE HYBRID SYSTEM OFF

Move the shift lever to the P (PARK) position and
apply the parking brake.

Press the ignition switch START/STOP button to turn the hybrid system off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Assist Charge Gauge

This shows the power consumed 02, or generated
01 by the electric motor.
For more information, refer to the “Hybrid System Overview” section and the
“Instruments and controls (section 2)” of your Owner’s Manual.0102
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 149/24/13 11:43 AM

15
Headlight Control Switch
HEADLIGHT CONTROL


Turn the headlight control switch to the
position
01 to turn on the front parking, tail, license plate and

instrument panel lights. Turn the switch to the
position 02 to turn on the headlights.
AUTOLIGHT SySTEM


The autolight system will automatically turn the headlights on when it i\
s dark and off when
it is light. The system will keep the headlights on for a period of time\
after you turn the
ignition off and all doors are closed.


To activate the autolight system, turn the headlight control switch to t\
he AUTO position
03
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight
control switch to the OFF,
position
01 or
position
02.
HIGH BEAM SELECT


Push the headlight control switch forward
04 to
select the high beam function. The blue indicator
light
illuminates in the instrument panel.
Pull the headlight switch back to the original
position to select the low beam. The blue
indicator light goes off.


Pull and release the headlight control switch
05 to
flash the headlight high beams on and off.
FOG LIGHT SWITCH


The headlights must be in auto, or the low
beams

selected for the fog lights to operate.


Turn the switch (inside collar) to the
position
06
to turn the fog lights on.


Turn the switch (inside collar)
to the OFF position to
turn the fog lights off.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
03
04
06
01
05
02
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 159/24/13 11:43 AM

first drive features
Windshield Wiper and Washer Switch

Move the lever to the following positions to operate
the windshield wipers:

01
Mist (MIST) – One sweep operation of the
front wipers.

02
Auto (AUTO) – Operates the speed-sensing
and rain-sensing (if so equipped) front wipers
intermittently. The intermittent speed can be
adjusted by twisting the time control ring

03
to increase or decrease wiper speed
or sensitivity.

04
Low (LO) – Front wipers operate at a
continuous low-speed.

05
High (HI) – Front wipers operate at a
continuous high-speed.

06
Pull the lever toward you to activate the
front washer. The front wipers will operate
several times.
RAIN-SENSING AUTO WIPER SySTEM (if so equipped)


The rain-sensing auto wiper system can automatically turn on the wipers \
and adjust the
wiper speed depending on the rainfall and the vehicle speed.


To set the rain-sensing auto wiper system, push the lever down to the AUTO position
02.
The wiper will sweep once while the ignition switch is in the ON position.


The rain sensor sensitivity level can be adjusted by turning the time co\
ntrol ring
03 toward
the front or toward the rear.
REAR WINDSHIELD WIPER AND WASHER

07
Intermittent (INT) – Rear wiper
operates intermittently.

08
Low (ON) – Rear wiper operates at a
continuous low-speed.

09
Push the lever forward to activate the
rear washer. The rear wiper will operate
several times.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
16
MIST
OFFAUTO LO
HI
INT
ON
01
02
04
06
07
08
05
09
03
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 169/24/13 11:43 AM

22
Power Outlets
12V OUTLETS

The power outlets are for powering electrical
accessories such as cellular telephones. They are
rated at 12 volt, 120W (10A) maximum.

To use a power outlet, open the cap.

The power outlet on the instrument panel 01,
inside the center console

02, on the back of the
center console

03 and in the cargo area 04

are powered only when the ignition switch
is in the ACC or ON position.
120V OUTLET (if so equipped)

The 120V outlet
05 is located on the back of the
center console.

To use the outlets for devices that require 120V
power, place the ignition in the ON position and
push the power inverter switch

06.

The switch will illuminate when enabled.
For more information, refer to the “Instruments and controls (section 2)”
of your Owner’s Manual.
01
04
05
03
06
02
first drive features
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 229/24/13 11:43 AM