warning light INFINITI QX80 2014 Manual PDF

5-32Starting and driving
SSD1030
Detection zone
The radar sensors can detect vehicles on
either side of your vehicle within the
detection zone shown as illustrated. This
detection zone starts from the outside
mirror of your vehicle and extends approxi-
mately 10 ft (3 m) behind the rear bumper,
and approximately 10 ft (3 m) sideways.
The BSW system operates above approxi-
mately 20 MPH (32 km/h). If the radar
sensors detect a vehicle in the detection
zone, the the Blind spot warning indicator
light illuminates. If the driver then acti-
vates the turn signal, a chime will sound
twice and the Blind spot warning indicator
light will flash. The Blind Spot Intervention
TMsystem
operates above approximately 37 MPH
(60 km/h). If the system detects a vehicle
in the detection zone and your vehicle is
approaching the lane marker, the Blind
Spot Intervention
TMsystem provides an
audible warning (three times), flashes the
Blind spot warning indicator light and
slightly applies the brakes for a short
period of time on one side to help return
the vehicle back to the traveling lane. The
Blind Spot Intervention
TMsystem provides
an audible warning and turns on or flashes
the Blind spot warning indicator light even
if the BSW system is off.
WARNING
. The BSW and Blind Spot InterventionTM
systems are not a replacement for proper
driving procedure and are not designed
to prevent contact with vehicles or
objects. When changing lanes, always
use the side and rear mirrors and turn
and look in the direction you will move
to ensure it is safe to change lanes.
Never rely solely on the BSW or Blind
Spot Intervention
TMsystem. .
Using the Blind Spot Intervention
TM
system under some road, lane marker
or weather conditions could lead to
improper system operation. Always rely
on your own steering and braking
operation to avoid accidents.
. The BSW and Blind Spot Intervention
TM
systems may not provide a warning or
brake control for vehicles that pass
through the detection zone quickly.

SSD1086
Blind spot warning indicator light
BSW SYSTEM OPERATION
If the radar sensors detect vehicles in the
detection zone, the Blind spot warning
indicator light located inside the outside
mirrors illuminates. If the turn signal is
then activated, the Blind spot warning
indicator light flashes and a chime sounds
twice. The indicator light continues to flash
until the detected vehicles leave the
detection zone.
The Blind spot warning indicator lights
illuminate for a few seconds when the
ignition switch is pushed to the ON
position.The brightness of the Blind spot warning
indicator lights is adjusted automatically
depending on the brightness of the ambi-
ent light.
A chime sounds if the radar sensors have
already detected vehicles when the driver
activates the turn signal. If a vehicle comes
into the detection zone after the driver
activates the turn signal, then only the
Blind spot warning indicator light flashes
and no chime sounds. (See
“BSW/Blind
Spot Intervention
TMdriving situations”
later in this section.)
SIC4335
Warning systems switch
Turning on or off the BSW system
The warning systems switch is used to turn
on and off the BSW system when it is
activated using the settings menu on the
center display. See “How to enable/disable
the BSW system using the settings menu”
later in this section.
When the warning systems switch is turned
off, the indicator
*1on the switch is off.
The indicator will also be off if the BSW, the
Lane Departure Warning (LDW) and the
Forward Collision Warning (FCW) systems
are deactivated.
Starting and driving5-33

5-34Starting and driving
For the LDW and FCW systems, see“Lane
Departure Warning (LDW)/Prevention (LDP)
system ”earlier in this section and
“Forward Collision Warning (FCW) system”
later in this section.
SSD0959
SSD1102
How to enable/disable the BSW
system using the settings menu
Perform the following steps to enable or
disable the BSW system.
1. Push the SETTING
*1button and high-
light the “Driver Assistance” key on the
display using the INFINITI controller.
Then push the ENTER
*2button.
2. Highlight the “Driver Assistance Warn-
ings” key, and push the ENTER
*2
button.

JVS0080X
3. Highlight the“Blind Spot Warning” key,
select ON (enabled) or OFF (disabled)
and push the ENTER
*2button.
SSD1086
Blind spot warning indicator light
SSD1029
Blind Spot InterventionTMON indicator
light (green)
Starting and driving5-35

5-36Starting and driving
SSD0957
Dynamic driver assistance switch
BLIND SPOT INTERVENTIONTMSYS-
TEM OPERATION
If the radar sensors detect vehicles in the
detection zone, the Blind spot warning
indicator light located inside the outside
mirrors illuminates. If your vehicle is
approaching a lane marker, the Blind spot
warning indicator light flashes and an
audible warning will sound three times.
Then the system applies the brakes on one
side of the vehicle for a short period of
time to help return the vehicle back to the
center of the lane. Blind Spot Interven-
tion
TMoperates regardless of turn signal usage.
NOTE:
.
Warning and brake control will only be
activated if the Blind spot warning
indicator light is already illuminated
when your vehicle approaches a lane
marker. If another vehicle comes into
the detection zone after your vehicle
has crossed a lane marker, no warning
or brake control will be activated. (See
“BSW/Blind Spot Intervention
TMdriv-
ing situations” later in this section.)
. The Blind Spot Intervention
TMsystem is
typically activated earlier than the
Lane Departure Prevention (LDP) sys-
tem when your vehicle is approaching
a lane marker.
The Blind Spot Intervention
TMsystem turns
on when the dynamic driver assistance
switch on the steering wheel is pushed
when the “Blind Spot Intervention” is
enabled in the settings menu on the center
display. The Blind Spot Intervention
TMON
indicator light (green) on the instrument
panel illuminates when the Blind Spot
Intervention
TMsystem is turned on.
The Blind Spot InterventionTMsystem
provides an audible warning and flashes the indicator light when Blind Spot Inter-
vention
TMis activated even if the BSW
system is off.

and parked vehicles may occasionally be
detected. This is a normal operating
condition.
. The camera may not detect lane markers
in the following situations and the Blind
Spot Intervention
TMsystem may not
operate properly.
—On roads where there are multiple parallel lane markers; lane markers
that are faded or not painted clearly;
yellow painted lane markers; non-
standard lane markers; lane markers
covered with water, dirt, snow, etc.
—On roads where discontinued lane
markers are still detectable.
—On roads where there are sharpcurves.
—On roads where there are sharply
contrasting objects, such as sha-
dows, snow, water, wheel ruts,
seams or lines remaining after road
repairs.
—On roads where the traveling lanemerges or separates.
—When the vehicle’s traveling direc-tion does not align with the lane
markers.
—When traveling close to the vehiclein front of you, which obstructs the
lane camera unit detection range.
—When rain, snow or dirt adheres tothe windshield in front of a lane
camera unit.
—When the headlights are not brightdue to dirt on the lens or if aiming is
not adjusted properly.
—When strong light enters a lane
camera unit. (For example, light
directly shines on the front of the
vehicle at sunrise or sunset.)
—When a sudden change in bright-ness occurs. (For example, when the
vehicle enters or exits a tunnel or
under a bridge.)
SSD1026
BSW/BLIND SPOT INTERVENTIONTM
DRIVING SITUATIONS
Another vehicle approaching from
behind
The Blind spot warning indicator light
illuminates if a vehicle enters the detection
zone from behind in an adjacent lane.
However, if the overtaking vehicle is
traveling much faster than your vehicle,
the indicator light may not illuminate
before the detected vehicle is beside your
vehicle. Always use the side and rear
mirrors and turn and look in the direction
your vehicle will move to ensure it is safe
Starting and driving5-39

5-40Starting and driving
to change lanes.
SSD1031
If the driver activates the turn signal, then
the Blind spot warning indicator light
flashes and a chime will sound twice.
NOTE:
If the driver activates the turn signal
before a vehicle enters the detection zone,
the Blind spot warning indicator light will
flash but no chime will sound when the
other vehicle is detected.
SSD1044
If the Blind Spot InterventionTMsystem is
on and your vehicle is approaching a lane
marker, the Blind spot warning indicator
light flashes and a chime will sound three
times. Then the Blind Spot Intervention
TM
system slightly applies the brakes on one
side to help return the vehicle back to the
center of the driving lane.

SSD1032
NOTE:
If you accelerate from a stop with a vehicle
in the detection zone, the other vehicle
may not be detected.
SSD1033
Overtaking other vehicles
The Blind spot warning indicator light
illuminates if you overtake a vehicle and
that vehicle stays in the detection zone for
approximately 3 seconds.
The radar sensors may not detect slower
moving vehicles if they are passed quickly.
SSD1034
If the driver activates the turn signal while
another vehicle is in the detection zone,
then the Blind spot warning indicator light
flashes and a chime will sound twice.
Starting and driving5-41

5-42Starting and driving
SSD1093
If the Blind Spot InterventionTMsystem is
on and your vehicle approaches a lane
marker while another vehicle is in the
detection zone, the Blind spot warning
indicator light flashes and a chime will
sound three times. Then, the Blind Spot
Intervention
TMsystem slightly applies the
brakes on one side to help return the
vehicle back to the center of the driving
lane.
SSD1036
NOTE:
When overtaking several vehicles in a row,
the vehicles after the first vehicle may not
be detected if they are traveling close
together.

SSD1037
Entering from the side
The Blind spot warning indicator light
illuminates if a vehicle enters the detection
zone from either side.
NOTE:
The radar sensors may not detect a vehicle
which is traveling at about the same speed
as your vehicle when it enters the detec-
tion zone.
SSD1038
If the driver activates the turn signal, then
the Blind spot warning indicator light
flashes and a chime will sound twice.
NOTE:
If the driver activates the turn signal
before a vehicle enters the detection zone,
the Blind spot warning indicator light will
flash but no chime will sound when
another vehicle is detected.
SSD1094
If the Blind Spot InterventionTMsystem is
on and your vehicle approaches the lane
marker while another vehicle is in the
detection zone, the Blind spot warning
indicator light flashes and a chime will
sound three times. Then, the Blind Spot
Intervention
TMsystem slightly applies the
brakes on one side to help return the
vehicle back to the center of the driving
lane.
Starting and driving5-43