ECU ISUZU AXIOM 2002 Service User Guide

DIFFERENTIAL (FRONT) 4A1±22
4. Install cross pin.

Be sure to install the cross pin so that it is in
alignment with the lock pin hole in the differential
cage.
425RS049
5. Install lock pin. After lock pin installation, stake the
cage to secure the lock pin.
6. Install ring gear and tighten the bolts in diagonal
sequence as illustrated.
Torque: 108 N´m (80 lb ft)
NOTE: Discard used bolts and install new ones.
415RS016

4A2±2DIFFERNTIAL (REAR)
General Description
The rear axle assembly is of the semi±floating type in
which the vehicle weight is carried on the axle housing .
The center line of the pinion gear is below the center line
of the ring gear (hypoid drive).
All parts necessary to transmit power from the propeller
shaft to the rear wheels are enclosed in a salisbury type
axle housing (a carrier casting with tubes pressed and
welded into the carrier). A removable aluminum cover at
the rear of the axle housing permits rear axle service
without removal of the entire assembly from the vehicle.
The 8.9 inch ring gear rear axle uses a conventional ring
and pinion gear set to transmit the driving force of the
engine to the rear wheels. This gear set transfers this
driving force at a 90 degree angle from the propeller shaft
to the drive shafts.
The axle shafts are supported at the wheel end of the
shaft by a roller bearing.
The pinion gear is supported by two tapered roller
bearings. The pinion depth is set by a shim pack located
between the gear end of the pinion and the roller bearing
that is pressed onto the pinion. The pinion bearing
preload is set by crushing a collapsible spacer between
the bearings in the axle housing.
The ring gear is bolted onto the differential case with 10
bolts.
The differential case is supported in the axle housing by
two tapered roller bearings. The differential and ring gear
are located in relationship to the pinion by using selective
shims and spacers between the bearing and the
differential case. To move the ring gear, shims are deleted
from one side and an equal amount are added to the other
side. These shims are also used to preload the bearings
which are pressed onto the differential case. Two bearing
caps are used to hold the differential into the rear axle
housing.
The differential is used to allow the wheels to turn at
different rates of speed while the rear axle continues to
transmit the driving force. This prevents tire scuffing
when going around corners and prevents premature wear
on internal axle parts.
The rear axle is sealed with a pinion seal, a seal at each
axle shaft end, and by a liquid gasket between the rear
cover and the axle housing.
Limited Slip Differential (LSD)
The axle assembly may be equipped with an limited slip
differential (LSD). It is similar to the standard differential
except that part of the torque from the ring gear is
transmitted through clutch packs between the side gears
and differential case.
The LSD construction permits differential action when
required for turning corners and transmits equal torque to
both wheels when driving straight ahead. However, when
one wheel tries to spin due to a patch of ice, etc., the
clutch packs automatically provide more torque to the
wheel which is not trying to spin.
In diagnosing customer complaints, it is important to
recognize two things:
1. If, both wheels slip, with unequal traction, the LSD
has done all it can possibly do.
2. In extreame cases of differences in traction, the
wheel with the least traction may spin after the LSD
has transferred as much torque as possible to the
non-slipping wheel.
Limited Slip Differntials impose additional requirements
on lubricants, and require a special lubricant or lubricant
additive. Use 80W90 GL±5 LSD lubricant.
Rear Axle Identification
The Bill of Material and build date information(1) is
stamped on the right axle tube on the rearward side.
The axle ratio is identified by a tag(3) which is secured by
a cover bolt. If the axle has limited-slip differntial, it also
will be identified with a tag(2) secured by a cover bolt.
425RX001

4A2±26DIFFERNTIAL (REAR)
Disassembly
1. Remove lock pin using a small drift.
425RS098
2. Remove the differential shaft by using a soft metal rod
and a hammer.
425RS043
3. Remove pinion mate gear and thrust washer.
4. Remove side gear and thrust washer.
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found through inspection.
Check the following parts.

Ring gear, pinion gear

Bearing

Side gear, pinion mate gear, differential shaft

Differential case, carrier

Thrust washer

Oil seal
Reassembly
1. Install side gear with thrust washer.
2. Install the pinion mate gear with thrust washer by
engaging it with the side gears while turning both
pinion mate gears simultaneously in the same
direction.
425RS048
3. Install differential shaft.
1. Be sure to install the differential shaft so that it is in
alignment with the lock pin hole in the differential
case.
425RS049
4. Install lock pin.
After lock pin installation, stake the case to secure the
lock pin.

4B2±1
DRIVE LINE CONTROL SYSTEM (TOD)
AXIOM
DRIVELINE/AXLE
DRIVELINE CONTROL SYSTEM (TOD)
CONTENTS
Service Precaution 4B2±1. . . . . . . . . . . . . . . . . . . . . .
General Description 4B2±2. . . . . . . . . . . . . . . . . . . . .
Transfer Position and Drive Mode 4B2±2. . . . . . . .
TOD Control 4B2±3. . . . . . . . . . . . . . . . . . . . . . . . . .
TOD Indicator Control 4B2±3. . . . . . . . . . . . . . . . . .
Abbreviations 4B2±3. . . . . . . . . . . . . . . . . . . . . . . . .
System Components 4B2±4. . . . . . . . . . . . . . . . . . . .
Parts Location 4B2±4. . . . . . . . . . . . . . . . . . . . . . . .
Front and Rear Speed Sensors 4B2±5. . . . . . . . . .
Electromagnetic Coil 4B2±5. . . . . . . . . . . . . . . . . . .
Multi Plate Disk Clutch Pack 4B2±5. . . . . . . . . . . .
Mechanical Lock Sleeve 4B2±5. . . . . . . . . . . . . . . .
High-Low Planetary Gear Set 4B2±6. . . . . . . . . . .
4H and 4L Switch 4B2±6. . . . . . . . . . . . . . . . . . . . . .
Transfer Connector (12-pin type) 4B2±6. . . . . . . .
Transfer Connector (8-pin type) 4B2±6. . . . . . . . .
TOD Indicator Lamps
(on the instrument panel) 4B2±7. . . . . . . . . . . . . .
Check Lamp 4B2±7. . . . . . . . . . . . . . . . . . . . . . . . . .
TOD ECU 4B2±8. . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-Low Shift Motor 4B2±9. . . . . . . . . . . . . . . . . . .
Motor Position and Encoder Position Code 4B2±10
Encode Position Plate 4B2±10. . . . . . . . . . . . . . . . . .
Shift High Range and Low Range 4B2±10. . . . . . . . Functions of TOD Switch and Indicator
Lamp 4B2±11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOD Switch and Indication of Drive Mode 4B2±11.
Check Lamp 4B2±13. . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis 4B2±14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Information Diagnosis 4B2±14. . . . . . . . . .
Self-diagnosis 4B2±14. . . . . . . . . . . . . . . . . . . . . . . . .
Precautions on Diagnosis 4B2±16. . . . . . . . . . . . . . .
Basic Diagnostic Flow Chart 4B2±18. . . . . . . . . . . . . .
Parts Location 4B2±19. . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Diagram 4B2±20. . . . . . . . . . . . . . . . . . . . . . . . .
Connector List 4B2±24. . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Failed Pin 4B2±26. . . . . . . . . . . . . . . . . . . . .
Connector Pin Assignment 4B2±26. . . . . . . . . . . . . .
Reference 4B2±28. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Failed TOD Control Unit Pin 4B2±30. . . . .
Tech 2 Scan Tool 4B2±32. . . . . . . . . . . . . . . . . . . . . .
Getting Started 4B2±33. . . . . . . . . . . . . . . . . . . . . . . .
Operating Procedure 4B2±33. . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Codes 4B2±35. . . . . . . . . . . . . . . .
Diagnosis from Trouble Codes 4B2±36. . . . . . . . . . . .
Trouble Diagnosis Depending on The Status
of TOD Indicator 4B2±67. . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis from Symptom 4B2±102. . . . . . . . . . . . . . . . .
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.

DRIVE LINE CONTROL SYSTEM (TOD) 4B2±2
General Description
412R200008
TOD (Torque on Demand) system is traction state control
system to vehicle.
Transfer Position and Drive Mode
Three drive modes can be selected through operation of
TOD switch and transfer lever.
Transfer Position
TOD SWITCHModeDrive mode
HIGH2HRWDRear wheel drive
TOD4WD
(HIGH)Electronically controlled torque split
four wheel drive
LOW4L4WD
(LOW)Low-speed mechanical lock-up four
wheel drive
The electronic control unit (ECU) judges the signals from
the TOD switch and controls the transfer drive mode and
shift-on-the-fly system status.

DRIVE LINE CONTROL SYSTEM (TOD) 4B2±8
TOD ECU
This control unit is mounted to the clutch pedal position
via a special bracket.
826R200019
Legend
(1) Brake Pedal Bracket

DRIVE LINE CONTROL SYSTEM (TOD) 4B2±16
How to Clear The Trouble Code
The trouble codes saved to the control unit can be deleted
by the following procedure if the starter switch is being in
the OFF position.
1. Short-circuit terminal 8 of the self-diagnostic
connector to GND (terminal 4 or 5).
2. Turn on the starter switch while maintaining the state
of step1, and stop short-circuiting terminal 8 to GND
within five seconds.
826R200011
3. If the conditions shown in steps 1 and 2 are met, the
trouble codes saved to the control unit are cleared.
(After the codes are completely deleted, the code 12
that indicates the normal condition is continuously
displayed.)
Precautions on Diagnosis
Replacement of Control Unit
The control unit itself rarely fails. In most cases, the
harnesses have failed (i.e. short-circuit) to cause
secondary troubles. Other cases include that the cause
has been unknown due to intermittent occurrence of
troubles and the troubles are removed accidentally along
with replacement of control unit, resulting in misjudgment
of cause. Therefore, before replacing the control unit,
check the connector joints and whether the unspecified
current flows in the control unit due to short-circuit
between harnesses.
Trouble Intermittently Observed
Troubles intermittently observed are mostly attributable
to temporary imperfect connection of harnesses and
connectors.
When such troubles are found, check the associated
circuit according to the following procedure.
1. Check whether improper connectors are plugged in
or connector terminals are completely engaged.
2. Check whether the terminals are deformed or
damaged. If yes, remove the deformation or damage
and connect the terminals securely.3. It is likely that wires in the harness are falsely broken.
Therefore, in examination of failed harness circuit,
shake the harness for check to such extent that the
harness will not be damaged.
Test Run of Failed TOD Vehicle
If the TOD indicator lamps experienced faulty operation
even once in the past, the failed portion can be identified
by use of the procedure ªDiagnosis from Trouble Codesº
or ªTrouble Diagnosis Depending on the Status of TOD
Indicatorº. If the troubles that are only recognized as
abnormal phenomena of the vehicle by the driver are
observed, conduct the test run in the following procedure
to reproduce the faulty phenomena and diagnose the fault
for each phenomenon.
1. Start the engine, and check that the TOD indicator
lamps are turned on for about two seconds for initial
check; the CHECK lamp goes off; and the TOD
indicator lamps display the specified drive mode. (If
the CHECK lamp starts blinking, read the trouble
codes and identify the failed portion.)
2. While keeping the vehicle standstill, operate the TOD
switch to change the modes: 2H mode"TOD
mode"4L mode"TOD mode"2H mode. Check
that the TOD indicator lamps correctly display the
status whenever the mode is changed. If the
transition status is displayed during the shift
operation, run the vehicle a little to complete shifting.
3. Slowly start the vehicle in the TOD mode, and add the
power to accelerate to at least 40 km/h (25 mph)and
maintain the speed for about two minutes. Apply the
brake to completely stop the vehicle. Repeat this test
pattern at least three times.
4. Turn the steering to the right end (or left end) in the
TOD mode, and slowly start the vehicle and make a
circle five times. Next, conduct the same test in the 2H
mode.
5. Slowly start the vehicle in the TOD mode, and
accelerate to at least 40 km/h (25 mph). Keep the
established speed, carefully change the mode in the
sequence ªTOD mode"2H mode "TOD modeº
while checking that the shift is complete in each mode
change. After the test, apply the brake to completely
stop the vehicle.
6. Slowly start the vehicle in the TOD mode, and
accelerate to at least 40 km/h (25 mph). Apply the
brake strongly so that the ABS works, and completely
stop the vehicle.
7. Slowly start the vehicle in the 4L mode, and
accelerate to at least 20 km/h (13 mph). Apply the
brake to completely stop the vehicle.
If the CHECK lamp starts blinking during the test run, read
the trouble codes and give appropriate maintenance
according to the diagnostic procedure. If the TOD
indicator lamps are lit abnormally during the run, check
the lighting condition and give appropriate maintenance
according to the diagnostic procedure. Even if the
phenomena are not observed, try to reproduce the
abnormal state reported by the customer to the possible
extent.

4B2±27
DRIVE LINE CONTROL SYSTEM (TOD)
No. CONTENTSNAME
26MTR POS1Shift Motor Position 1
27POSCAT Position C
28POSAAT Position A
29DIAGDiagnostic Input
30TOD SW ATOD Switch A (2H)
314H SW4H Switch Input
32FT. SIGFront Speed Signal
33ABS INABS In
34VBPower Bat
35MTR H-LPower Shift Motor H-L
364WD OUT4WD Signal Output
37BRAKE SWBrake Switch Input
38MTR POS4Shift Motor Position 4
39MTR POS2Shift Motor Position 2
40LIGHTING SWLighting Switch Input
41POSBAT Position B
42AXLE SWAxle Switch Input
43TOD SWBTOD Switch B (4L)
444L SW4L Switch Input
45RR. SIGRear Speed Signal
46GND. 1ECU Ground 1
47GND. 2ECU Ground 2
48MTR L-HPower Shift Motor L-H

DRIVE LINE CONTROL SYSTEM (TOD) 4B2±30
Checking Failed TOD Control Unit Pin
NOTE:
1. Unplug the ECU connector and the pins, unless
otherwise specified.
2. Before removing the ECU, turn off the ignition switch.
3. If the standard values are not observed, check the
pins with other testers.
Check
Pin
No.Circuit to be
testedIgnition
Switch
PositionEngine
StateUnit
Scale/
RangeMeasure
between
Pin No.Standard ValueNote
22P-GNDOFFSTOP
22, 47Continuity : OK
46GNDIOFFSTOP
46, 47Continuity : OK
47GND 2OFFSTOP
47, GNDContinuity : OK
314H SWOFFSTOP
31, 47No continuity
(high, 4L) : OK
444L SWOFFSTOP
44, 47No continuity
(high) and
continuity (4L) :
OK
42AXLE SWONRUN
42, 47Continuity(TOD,
4L) : OKRemove ECU connector and start
the engine. Move the vehicle forth
and back to connect axle surely.
29DIAGOFFSTOP
29 (TOD),
8 (DLC
Connec-
tor)Continuity : OKDLC connector terminal 8
7IND.AONSTOPDCV7 (+), 47
(±)8.0 ~14.5 Vwhen the indicator lamp is turned
off.
20CHECK
TODONSTOPDCV20 (+), 47
(±)8.0 ~14.5 VWhen the indicator lamp is turned
off.
33ABS INONSTOPDCV33 (+), 47
(±)6.0 ~11.0 V
12REFONSTOPDCV12 (+), 47
(±)5 ~9 VConnect ECU
32FRT.(+)ONSTOPDCV32 (+), 47
(±)0.7 ~6 VConnect ECU and move the
vehicle (off one tooth of speed
sensor ring) making sure of
voltage change.
45RR.(+)ONSTOPDCV45 (+), 47
(±)0.7 ~6 VConnect ECU and move the
vehicle (off one tooth of speed
sensor ring) making sure of
voltage change.
13COM(-)ONSTOPDCV13 (+), 47
(±)0VConnect ECU
14VIGONSTOPDCV14 (+), 47
(±)8 ~14.5 V
34VBOFFSTOPDCV34 (+), 47
(±)8.0 ~14.5 V
37BRAKE
SWOFFSTOPDCV37 (+), 47
(±)8 ~14.5 VPress brake pedal
15TPSONSTOPDCV15 (+), 47
(±)PWM duty cycle
10%(MAX) ± 90
%(MIN)Step on the accelerator pedal and
make sure that duty cycle
changes.

4B2±35
DRIVE LINE CONTROL SYSTEM (TOD)
Diagnostic Trouble Codes
CodeTech 2 code
(P code)ItemDiagnosisCheck flow No.
12ÐStart codeNormalÐ
13P1735RefShorted GND6
14P1731Front speed sensorInput abnormality (open, sig or com)2
15P1736RefShorted VB6
16P1737Front speed sensorInput abnormality4
17P1774Inhibitor switchInput abnormality8
21P1716TPSShorted or disconnected wiring,
abnormality in input7
23ÐECUCPU abnormality1
24P1733Rear speed sensorInput abnormality (open, sig or com)3
27P1738Rear speed sensorInput abnormality5
28P1760ADC (+) & AXLE SWOutput abnormality10
31P1721EMC (+)Shorted VB, disconnected coil/wiring or
shorted GND9
32P1761ADC (+)Shorted VB or disconnected wiring11
33P1762ADC (+)Shorted GND12
36ÐECUCPU abnormality1
37P1712ECUCPU abnormality1
38P1714ECUCPU abnormality1
41P1741Hight-Low shift motorShorted GND or disconnected wiring13
42P1773Hight-Low shift motorUser operation error (not failure)14
43P1743Hight-Low shift motorMotor moving more than 5s15
55P1755Hight-Low shift motorInput abnormality of motor position signal16
TPS : Throttle Position Sensor
EMC : Electromagnetic coil
ADC : Shift on the fly (Axle Dis Connect)