Timing belt ISUZU AXIOM 2002 Service User Guide

6A±34
ENGINE MECHANICAL (6VE1 3.5L)
014RW024
Legend
(1) Right Bank
(2) Left Bank(3) Alignment Mark on Camshaft Drive Gear
(4) Alignment Mark on Camshaft
(5) Alignment Mark on Retainer
3. Tighten twenty bolts on numerical order an one
side bank as shown in the illustration.
Torque : 10 N´m (87 lb in)
014RW031
5. Install cylinder head cover RH.

Refer to installation procedure for CYLINDER
HEAD COVER RH in this manual.
6. Install cylinder head cover LH.

Refer to installation procedure for CYLINDER
HEAD COVER LH in this manual.
7. Install timing belt.

Refer to installation procedure for TIMING BELT in
this manual.
8. Install crankshaft pulley.

Refer to installation procedure for CRANKSHAFT
PULLEY in this manual.

6A±35
ENGINE MECHANICAL (6VE1 3.5L)
Cylinder Head
Removal
1. Remove engine hood.
2. Disconnect battery ground cable.
3. Drain radiator coolant.
4. Drain engine oil.
5. Remove crankshaft pulley.

Refer to removal procedure for Crankshaft Pulley in
this manual.
6. Remove timing belt.

Refer to removal procedure for Timing Belt in this
manual.
7. Remove cylinder head cover LH.

Refer to removal procedure for Cylinder Head
Cover LH in this manual.
8. Remove cylinder head cover RH.

Refer to removal procedure for Cylinder Head
Cover RH in this manual.
9. Remove common chamber.

Refer to removal procedure for Common Chamber
in this manual.
10. Remove cylinder head assembly.
1. Loosen head bolts in reverse of tightening
sequence.
2. Remove cylinder head assembly.
014RW028
Legend
(1) Cylinder Head
(2) Cylinder Head Bolt
(3) Camshaft
Installation
1. Install cylinder head assembly to cylinder block.
A. Put cylinder head gasket on the cylinder block.
NOTE: There is discrimination mark ªRº for right bank
and ªLº for left bank on the cylinder head gasket as shown
in the illustration.
Do not reuse cylinder head gasket.
011RW005
B. Align dowel pin hole to dowel pin on the cylinder
block.
C. Position cylinder head on the cylinder block.
D. Tighten two bolts temporarily by hand to prevent
the cylinder head assembly from moving.
E. Using J-24239-01 cylinder head bolt wrench,
tighten bolts in numerical order as shown in the
illustration to the specified torque.

6A±36
ENGINE MECHANICAL (6VE1 3.5L)
NOTE: Do not reuse cylinder head bolts.
Do not apply any lubricant to the cylinder head bolts.
Torque :
Temporary : 29 N´m (22 lb ft)
Final : 64 N´m (47 lb ft)
014RW029
2. Install common chamber.

Refer to installation procedure for Common
Chamber in this manual.
3. Install cylinder head cover RH.

Refer to installation procedure for Cylinder Head
Cover RH in this manual.
4. Install cylinder head cover LH.

Refer to installation procedure for Cylinder Head
Cover LH in this manual.
5. Install timing belt.

Refer to installation procedure for Timing Belt in this
manual.
6. Install crankshaft pulley.

Refer to installation procedure for Crankshaft
Pulley in this manual.

6A±40
ENGINE MECHANICAL (6VE1 3.5L)
Crankshaft and Main Bearings
Removal
F06RY002
Legend
(1) Engine Assembly
(2) Crankshaft Pulley
(3) Timing Belt Cover
(4) Timing Belt
(5) Crankcase with Oil Pan
(6) Oil Pipe
(7) Oil Strainer(8) Oil Pump Assembly
(9) Cylinder Body Side Bolt
(10) Oil Gallery
(11) Flywheel
(12) Rear Oil Seal Retainer
(13) Connecting Rod Cap
(14) Crankshaft Main Bearing Cap
(15) Crankshaft and Main Bearing
1. Remove engine assembly.

Refer to removal procedure for Engine Assembly in
this manual.
2. Remove timing belt.

Refer to removal procedure for Timing Belt in this
manual.3. Remove oil pan and crankcase.

Refer to removal procedure for Oil Pan and
Crankcase in this manual.
4. Remove oil pipe with O-ring.
5. Remove oil strainer assembly with O-ring.

6A±44
ENGINE MECHANICAL (6VE1 3.5L)

Tighten fixing bolts to the specified torque.
Torque : 25 N´m (18 lb ft)
013RW003
013RW002
13. Install timing belt.

Refer to installation procedure for Timing Belt in this
manual.
14. Install engine assembly.

Refer to installation procedure for Engine
Assembly in this manual.

6A±87
ENGINE MECHANICAL (6VE1 3.5L)
Main Data and Specification
General Specification
ItemSpecificationsItem6VE1
Engine type, number of cylinders and arrangementWater cooled, four cycle V6
Form of combustion chamberPent-roof type
Valve mechanism4-Cams, 4-Valves, DOHC Gear & Belt Drive
Cylinder liner typeCasted in cylinder drive
Total piston displacement3494 cc
Cylinder bore x stroke93.4mm x 85mm
(3.677 in x 3.346 in)
Compression ratio9.1
Compression pressure at 300rpm1.37 MPa (14.0 Kg/cm2)
Engine idling speed rpmNon adjustable (750)
Valve clearanceIntake: 0.28 mm (0.11 in)
Exhaust: 0.30mm (0.12in)
Oil capacity5.3 liters
Ignition timingNon adjustable (20
BTDC at idle rpm)
Spark plugPK16PR11, RC10PYP4, K16PR-P11
Plug gap1.0 mm±1.1 mm(0.0394 in ± 0.0433 in)

6A±90
ENGINE MECHANICAL (6VE1 3.5L)
Crankshaft main bearing, Flywheel, Crankcase, Oil pan, Timing belt tensioner, Timing pulley, Timing belt
cover, Oil pump, Oil gallery, Oil strainer and water pump
E06R100004

6B±2
ENGINE COOLING (6VE1 3.5L)
General Description
030RW001
Legend
(1) Water Pump
(2) Thermostat
(3) Radiator
(4) Reserve Tank
(5) Cooling Fan
(6) Cylinder Block(7) Cylinder Head
(8) Right Bank
(9) Throttle Body
(10) Cylinder Block
(11) Cylinder Head
(12) Left Bank
(13) Heater
The cooling system is a pressurized Engine Coolant (EC)
forced circulation type which consists of a water pump,
thermostat cooling fan, radiator and other components.
The automatic transmission fluid is cooled by the EC in
the radiator.
Water Pump
The EC pump is a centrifugal impeller type and is driven
by a timing belt.
030RS001

6B±6
ENGINE COOLING (6VE1 3.5L)
Water Pump
Water Pump and Associated Parts
030RS002
Legend
(1) Timing Belt
(2) Idle Pulley(3) Water Pump Assembly
(4) Gasket
Removal
1. Disconnect battery ground cable.
2. Drain coolant.
3. Radiator hose (on inlet pipe side).
4. Remove timing belt. Refer to ªTiming Beltº in this
manual.
5. Remove Idle pulley.
6. Remove water pump assembly.
7. Remove gasket.
Inspection
Make necessary repair and parts replacement if extreme
wear or damage is found during inspection. Should any of
the following problems occur, the entire water pump
assembly must be replaced.

Crack in the water pump body

EC leakage from the seal unit

Play or abnormal noise in the bearing

Cracks or corrosion in the impeller
Installation
1. Install gasket, clean the mating surface of gasket
before installation.
2. Install water pump assembly and tighten bolts to the
specified torque.
Torque: 25 N´m (18 lb ft)

Tightening order
The tightening order are in the illustrate.NOTE: To prevent the oil leakage, apply the LOCTITE
262 or an equivalent, to the arrow marked fixing bolt
thread.
030RW008
3. Idle pulley

Install idle pulley and tighten bolt to the specified
torque.
Torque: 52 N´m (38 lb ft)
4. Timing belt

Install timing belt. Refer to timing belt installation
step in ªTiming Beltº in this manual.
5. Connect radiator inlet hose and replenish EC.
6. Connect battery ground cable.

6E±105
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Engine Cranks But Will Not Run

 
StepNo Ye s Value(s) Action
23Refer to Engine Mechanical Diagnosis to diagnose the
following conditions:

Faulty or incorrect camshaft drive belts

Leaking or sticky valves or rings

Excessive valve deposits

Weak valve springs

Incorrect valve timing

Leaking head gasket
Is the action complete?
ÐVerify repairGo to Step 25
24Observe the ªEngine Speedº data display on the Tech 2
while cranking the engine.
Is the engine RPM indicated?
ÐGo to Step 25Go to Step 34
251. Disconnect the 7-pin gray connector at the rear of
the air filter beneath the point where the air duct
attaches to the MAF sensor.
2. Ignition ªONº.
3. Using a test light connected to ground, probe the
ignition terminal at the PCM (female) side of the
7-pin connector.
Is the test light ªONº?
ÐGo to Step 26Go to Step 32
261. At the PCM (female) side of the connector, connect
a test light between the ignition + terminal and one
of the injector driver circuits at the same connector.
2. Ignition ªONº.
3. Observe the test light, and repeat the test for each
injector driver circuit.
Did the test light stay on when checking any of the 6
injector driver circuits?
ÐGo to Step 27Go to Step 29
271. Ignition ªOFFº, disconnect the PCM.
2. Ignition ªONº, observe the test light.
Is the test light ªONº?
ÐGo to Step 28Go to Step 33
28Locate and repair the short to ground in the injector
driver circuit.
Is the action complete?
ÐVerify repairÐ
291. Using the same test location as in step 26, connect
a test light between the ignition terminal and one of
the driver circuits.
2. Crank the engine and observe the test light.
3. Repeat for each injector driver circuit.
Did the light blink during the test for each circuit?
ÐGo to Step 31Go to Step 30
30Check for an open injector driver circuit.
Was a problem found?
ÐVerify repairGo to Step 33