four wheel drive ISUZU AXIOM 2002 Service User Guide

6A±46
ENGINE MECHANICAL (6VE1 3.5L)
Engine Assembly
Removal
035R200001
1. Disconnect battery ground and positive cable.
2. Remove battery.
3. Make alignment mark on the engine hood and hinges
before removal in order to return the hood to original
position exactly.
4. Remove engine hood.
5. Drain radiator coolant.
6. Disconnect Ion sensing module harness connectors,
and manifold absolute pressure sensor harness
connectors from sensor on common chamber.
7. Disconnect throttle position sensor harness
connectors from throttle body.
8. Disconnect air duct with air cleaner cover.
9. Remove air cleaner assembly.
10. Disconnect canister vacuum hose.
11. Disconnect vacuum booster hose.
12. Disconnect three engine harness connectors.
13. Disconnect harness connector to transmission (left
front side of engine compartment), disconnect shift
on the fly harness connector from front side of front
axle and remove transmission harness bracket from
engine left side.
14. Disconnect ground cable between engine and frame.
15. Disconnect bonding cable connector on the back of
right dash panel.
16. Disconnect bonding cable terminal on the left bank.
17. Disconnect starter harness connector from starter.
18. Disconnect generator harness connector from
generator.
19. Disconnect coolant reserve tank hose from radiator.
20. Remove radiator upper and lower hoses.21. Remove upper fan shroud.
22. Remove cooling fan assembly four fixing nuts, then
the cooling fan assembly.
23. Move drive belt tensioner to loose side using wrench
then remove drive belt.
24. Remove power steering pump fixing bolts, then
power steering pump. Place the power steering pump
along with piping on the body side.
25. Remove air conditioning compressor fixing bolts from
bracket and place the compressor along with piping
on the body side.
26. Remove four O
2 sensor harness connectors (two
each bank) from exhaust front pipe.
27. Remove three exhaust pipe fixing nuts from each
bank.
28. Remove two exhaust pipe fixing nuts from each
exhaust pipe, then move exhaust pipe to rear side of
vehicle.
29. Remove flywheel dust covers.
30. Disconnect two heater hoses from engine.
31. Disconnect fuel hoses from right side of transmission.
CAUTION: Plug fuel pipes on engine side and fuel
hoses from fuel tank.
32. Remove transmission assembly. Refer to
Transmission section in this manual.
33. Support the engine by engine hoist.
34. Remove two left side engine mount fixing bolts from
engine mount on chassis side.
35. Remove two right side engine mount fixing bolts from
engine mount on chassis side.
36. Remove engine assembly.

7A±3 AUTOMATIC TRANSMISSION (4L30±E)
Construction
A07R100002
Legend
(1) Torque Converter Clutch (TCC)
(2) Overdrive Free Wheel (One Way Clutch)
(OFW)
(3) Fourth Clutch (C4)
(4) Overrun Clutch (OC)
(5) Overdrive Unit(6) Reverse Clutch (RC)
(7) Second Clutch (C2)
(8) Third Clutch (C3)
(9) Principle Sprag Assembly (One Way Clutch)
(PFW)
(10) Ravigneaux Planetary Gear Set
(11) Brake Band (B)

SUPPLEMENTAL RESTRAINT SYSTEM 9J±28
damaged, replace them. The steering column and wheel
must be dimensionally checked to determine if they are
damaged. Refer to in this Section 9J±3 of this manual.
Never use SRS parts from another vehicle. This does not
include remanufactured parts purchased from an
authorized Retailer; they may be used for SRS repairs.
Do not attempt to repair the SDM, the SRS harness, the
SRS coil assembly, the air bag assembly, the steeringwheel, or the steering column. Service of these items is
replacement only. Verify replacement part numbers.
CAUTION: P r o p e r o p e r a t i o n o f t h e S D M a n d
Supplemental Restraint System (SRS) requires that
any repairs to the vehicle structure return it to its
original production configuration.
Sensing and Diagnostic Module (SDM)
Service Precautions
WARNING:DURING SERVICE PROCEDURES, BE
VERY CAREFUL WHEN HANDLING SDM. NEVER
STRIKE OR JAR SDM. UNDER SOME
CIRCUMSTANCES, IT COULD CAUSE
DEPLOYMENT AND RESULT IN PERSONAL INJURY
OR IMPROPER OPERATION OF THE
SUPPLEMENTAL RESTRAINT SYSTEM (SRS). SDM
MOUNTING BRACKET BOLTS MUST BE
CAREFULLY TORQUED TO ASSURE PROPER
OPERATION. NEVER POWER UP THE SRS WHEN
SDM IS NOT RIGIDLY ATTACHED TO THE VEHICLE.
THE SDM COULD BE ACTIVATED WHEN POWERED
WHILE NOT RIGIDLY ATTACHED TO THE VEHICLE
WHICH COULD CAUSE DEPLOYMENT AND RESULT
IN PERSONAL INJURY.
WARNING: PROPER OPERATION OF THE SENSING
AND DIAGNOSTIC MODULE (SDM) REQUIRES THE
SDM TO BE RIGIDLY ATTACHED TO THE VEHICLE
STRUCTURE AND THAT THE ARROW ON THE
SENSOR BE POINTING TOWARD THE FRONT OF
THE VEHICLE.
SDM is specifically calibrated and is keyed to the SDM
location SRS wiring harness. Caution should be used to
ensure proper location of the SDM. The keying of the
SDM to its location and wiring harness connectors should
never be modified in the field.
Removal
1. Disable the SRS. (Refer to ªDisable the SRSº in this
manual)
2. Remove dressing panel around the radio and
disconnect cigar lighter harness.
3. Remove the transfer sift lever knob.
4. Remove the center console.
5. Remove three connector from PCM.
6. Remove PCM with bracket.(Fixed four bolts)
7. Remove right side stay between instrument panel
and floor.
8. Remove driver and passenger seat.
9. Turn over carpet to rear side.10. Remove air conditioning duct for rear seat.
(Transform the duct during removing it)
827RW023
11. Pull CPA (1) (Connector Position Assurance±red
color) out and push connector lock down to
disconnect the SDM harness connector (2).
12. Remove the three SDM fixing bolts (4) and remove
SDM (3).
827RW022