fuel pressure ISUZU AXIOM 2002 Service Service Manual

6E±70
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Injector Coil Test Procedure (Steps 1-6) and Injector Balance Test Procedure
(Steps 7-11)

StepActionValue(s)Ye sNo
1Was the ªOn-Board Diagnostic (OBD) System Checkº
performed?
ÐGo to Step 2
Go to OBD
System
Check
21. Turn the engine ªOFFº.
NOTE: In order to prevent flooding of a single cylinder
and possible engine damage, relieve the fuel pressure
before performing the fuel injector coil test procedure.
2. Relieve the fuel pressure. Refer to
Test Description
Number 2.
3. Connect the J 39021-5V Fuel Injector Tester to B+
and ground, and to the J 39021-90 Injector Switch
Box.
4. Connect the injector switch box to the grey fuel
injector harness connector located on the front of
the EVAP canister bracket.
5. Set the amperage supply selector switch on the fuel
injector tester to the ªCoil Testº 0.5 amp position.
6. Connect the leads from the J 39200 Digital
Voltmeter (DVM) to the injector tester. Refer to the
illustrations associated with the test description.
7. Set the DVM to the tenths scale (0.0).
8. Observe the engine coolant temperature.
Is the engine coolant temperature within the specified
values?
10
C (50
F)
to 35
C
(95
F)
Go to Step 3Go to Step 5
31. Set injector switch box injector #1.
2. Press the ªPush to Start Testº button on the fuel
injector tester.
3. Observe the voltage reading on the DVM.
IMPORTANT:The voltage reading may rise during the
test.
4. Record the lowest voltage observed after the first
second of the test.
5. Set the injector switch box to the next injector and
repeat steps 2, 3, and 4.
Did any fuel injector have an erratic voltage reading
(large fluctuations in voltage that did not stabilize) or a
voltage reading outside of the specified values?
5.7-6.6 VGo to Step 4Go to Step 7
4Replace the faulty fuel injector(s). Refer to Fuel
Injector.
Is the action complete?ÐGo to Step 7Ð

6E±71
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Injector Coil Test Procedure (Steps 1-6) and Injector Balance Test Procedure
(Steps 7-11)

 
StepNo Ye s Value(s) Action
51. Set injector switch box injector #1.
2. Press the ªPush to Start Testº button on the fuel
injector tester.
3. Observe the voltage reading on the DVM.
IMPORTANT:The voltage reading may rise during the
test.
4. Record the lowest voltage observed after the first
second of the test.
5. Set the injector switch box to the next injector and
repeat steps 2, 3, and 4.
Did any fuel injector have an erratic voltage reading
(large fluctuations in voltage that did not stabilize) or a
voltage reading above the specified value?
9.5 VGo to Step 4Go to Step 6
61. Identify the highest voltage reading recorded (other
than those above 9.5 V).
2. Subtract the voltage reading of each injector from
the highest voltage selected in step 1. Repeat until
you have a subtracted value for each injector.
For any injector, is the subtracted Value in step 2
greater than the specified value?
0.6 VGo to Step 4Go to Step 7
7CAUTION: In order to reduce the risk of fire and
personal injury, wrap a shop towel around the
fuel pressure connection. The towel will absorb
any fuel leakage that occurs during the
connection of the fuel pressure gauge. Place the
towel in an approved container when the
connection of the fuel pressure gauge is
complete.
1. Connect the J 34730-1 Fuel Pressure Gauge to the
fuel pressure test port.
2. Energize the fuel pump using the Tech 2.
3. Place the bleed hose of the fuel pressure gauge into
an approved gasoline container.
4. Bleed the air out of the fuel pressure gauge.
5. With the fuel pump running, observe the reading on
the fuel pressure gauge.
Is the fuel pressure within the specified values?
296-376 kPa
(43-55 psi)
Go to Step 8
Go to Fuel
System
Diagnosis
8Turn the fuel pump ªOFFº.
Does the fuel pressure remain constant?
ÐGo to Step 9
Go to Fuel
System
Diagnosis

6E±72
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Injector Coil Test Procedure (Steps 1-6) and Injector Balance Test Procedure
(Steps 7-11)

 
StepNo Ye s Value(s) Action
91. Connect the J 39021-5V Fuel Injector Tester and J
39021-90 Injector Switch Box the fuel injector
harness connector.
2. Set the amperage supply selector switch on the fuel
injector tester to the ªBalance Testº 0.5±2.5 amp
position.
3. Using the Tech 2 turn the fuel pump ªONº then
ªOFFº in order to pressurize the fuel system.
4. Record the fuel pressure indicated by the fuel
pressure gauge after the fuel pressure stabilizes.
This is the first pressure reading.
5. Energize the fuel injector by depressing the ªPush
to Start Testº button on the fuel injector tester.
6. Record the fuel pressure indicated by the fuel
pressure gauge after the fuel pressure gauge
needle has stopped moving. This is the second
pressure reading.
7. Repeat steps 1 through 6 for each fuel injector.
8. Subtract the second pressure reading from the first
pressure reading for one fuel injector. The result is
the pressure drop value.
9. Obtain a pressure drop value for each fuel injector.
10.Add all of the individual pressure drop values. This
is the total pressure drop.
11. Divide the total pressure drop by the number of fuel
injectors. This is the average pressure drop.
Does any fuel injector have a pressure drop value that
is either higher than the average pressure drop or lower
than the average pressure drop by the specified value?
10 kPa
(1.5 psi)
Go to Step 10
Go to OBD
System
Check
10Re-test any fuel injector that does not meet the
specification. Refer to the procedure in step 9.
NOTE: Do not repeat any portion of this test before
running the engine in order to prevent the engine from
flooding.
Does any fuel injector still have a pressure drop value
that is either higher than the average pressure drop or
lower than the average pressure drop by the specified
value?
10 kPa
(1.5 psi)
Go to Step 11
Go to
Symptoms
11Replace the faulty fuel injector(s). Refer to Fuel
Injector.
Is the action complete?ÐVerify repairÐ

6E±73
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Powertrain Control Module (PCM)
Diagnosis
To read and clear diagnostic trouble codes, use a Tech 2.
IMPORTANT:Use of a Tech 2 is recommended to clear
diagnostic trouble codes from the PCM memory.
Diagnostic trouble codes can also be cleared by turning
the ignition ªOFFº and disconnecting the battery power
from the PCM for 30 seconds. Turning off the ignition and
disconnecting the battery power from the PCM will cause
all diagnostic information in the PCM memory to be
cleared. Therefore, all the diagnostic tests will have to be
re-run.
Since the PCM can have a failure which may affect only
one circuit, following the diagnostic procedures in this
section will determine which circuit has a problem and
where it is.
If a diagnostic chart indicates that the PCM connections
or the PCM is the cause of a problem, and the PCM is
replaced, but this does not correct the problem, one of the
following may be the reason:

There is a problem with the PCM terminal
connections. The terminals may have to be removed
from the connector in order to check them properly.

EEPROM program is not correct for the application.
Incorrect components or reprogramming the PCM
with the wrong EEPROM program may cause a
malfunction and may or may not set a DTC.

The problem is intermittent. This means that the
problem is not present at the time the system is being
checked. In this case, refer to the
Symptoms portion
of the manual and make a careful physical inspection
of all component and wiring associated with the
affected system.

There is a shorted solenoid, relay coil, or harness.
Solenoids and relays are turned ªONº and ªOFFº by
the PCM using internal electronic switches called
drivers. A shorted solenoid, relay coil, or harness will
not damage the PCM but will cause the solenoid or
relay to be inoperative.
Multiple PCM Information Sensor
DTCs Set
Circuit Description
The powertrain control module (PCM) monitors various
sensors to determine the engine operating conditions.
The PCM controls fuel delivery, spark advance,
transmission operation, and emission control device
operation based on the sensor inputs.
The PCM provides a sensor ground to all of the sensors.
The PCM applies 5 volts through a pull±up resistor, and
determines the status of the following sensors by
monitoring the voltage present between the 5±volt supply
and the resistor:

The engine coolant temperature (ECT) sensor

The intake air temperature (IAT) sensor

The transmission fluid temperature (TFT) sensorThe PCM provides the following sensors with a 5±volt
reference and a sensor ground signal:
1

The exhaust gas recirculating (EGR) pintle position
sensor

The manifold absolute pressure (MAP) sensor

The throttle position (TP) sensor 1

The acceleration position (AP) sensor 1

The acceleration position (AP) sensor 3

The Vapor Pressure Sensor
2

The Crank position (CKP) sensor

The throttle position (TP) sensor 2

The acceleration position (AP) sensor 2
The PCM monitors the separate feedback signals from
these sensors in order to determine their operating
status.
Diagnostic Aids
IMPORTANT:Be sure to inspect PCM and engine
grounds for being secure and clean.
A short to voltage in one of the sensor input circuits may
cause one or more of the following DTCs to be set:

P0425

P0108, P1106

P0406

P1120, P1515, P1221, P1516, P1635

P1275, P1639, P1271, P1273

P1285, P1272, P1273

P0336, P0337

P1220, P1515, P1221, P1515, P1516

P1280, P1271, P1272
IMPORTANT:If a sensor input circuit has been shorted
to voltage, ensure that the sensor is not damaged. A
damaged sensor will continue to indicate a high or low
voltage after the affected circuit has been repaired. If the
sensor has been damaged, replace it.
An open in the sensor ground circuit between the PCM
and the splice will cause one or more of the following
DTCs to be set:

P0425

P0108, P1106

P0406

P1120, P1515, P1221, P1516, P1635

P1275, P1639, P1271, P1273

P1285, P1272, P1273

P0336, P0337

P1220, P1515, P1221, P1515, P1516

P1280, P1271, P1272
A short to ground in the 5±volt reference A or B circuit will
cause one or more of the following DTCs to be set:

P0453

P0106, P0107, P1107

P0401, P1404, P0405

P1120, P1515, P1221, P1516, P1635

6E±74
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS

P1275, P1639, P1271, P1273

P1285, P1272, P1273

P0336, P0337

P1220, P1515, P1221, P1515, P1516

P1280, P1271, P1272
Check for the following conditions:

Poor connection at PCM. Inspect the harness
connectors for backed±out terminals, improper
mating, broken locks, improperly formed or damage
terminals, and a poor terminal±to±wire connection.
Damaged harness. Inspect the wiring harness for
damage. If the harness is not damaged, observe an
affected sensor fs displayed value on the Tech 2 with
the ignition ªONº and the engine ªOFFº while you
move the connectors and the wiring harnesses
related to the following sensors:

Vapor Pressure (Fuel Tank Pressure) Sensor

MAP Sensor

EGR

TPS1/TPS2

APS1/APS2/APS3

CKP
Multiple PCM Information Sensor DTCs Set

StepActionValue(s)Ye sNo
1Was the ªOn-Board (OBD) System Checkº performed?
ÐGo to Step 2
Go to OBD
System
Check
21. Turn the ignition ªOFFº, disconnect the PCM.
2. Turn the ignition ªONº, check the 5 volt reference 1
and 2 circuit for the following conditions:

A poor connection at the PCM.

An open between the PCM connector and the
splice.

A short to ground.

A short to voltage.
Is there an open or short?
ÐGo to Step 3Go to Step 4
3Repair the open or short.
Is the action complete?
ÐVerify repairÐ
4Check the sensor ground circuit for the following
conditions:

A poor connection at the PCM or the affected
sensors.

An open between the PCM connector and the
affected sensors.
Is there an open or a poor connection?
ÐGo to Step 5Go to Step 6
5Repair the open or the poor connection.
Is the action complete?
ÐVerify repairÐ
6Following below the DTCs stored:
P1635, P1639
Ð
Go to
applicable
DTC table
Go to Step 7
7 Measure the resistance below the items:

Between EGR sensor supply circuit and Vapor
Pressure Sensor supply circuit.

Between MAP sensor supply circuit and Vapor
Pressure Sensor supply circuit.

Between Vapor Pressure Sensor supply circuit
and PCM harness connector. (5Volt supply
circuit)
Is the resistance near the specified value?
ÐGo to Step 9Go to Step 8

6E±76
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Exhaust Gas Recirculation (EGR)
Diagnosis
An EGR flow check diagnosis of the linear EGR system is
covered by DTC P0401. Pintle position error diagnosis is
covered by DTC P0402, P0404, P1404, P0405, P0406. If
EGR diagnostic trouble codes P0401 and/or P0402,
P0404, P1404, P0405, P0406 are encountered, refer to
the DTC charts.
Engine Tech 2 Data Definitions and
Ranges
A/C CLUTCH ± Tech 2 Displays ON or OFF ±
Indicates whether the PCM has commanded the A/C
clutch ON. Used in A/C system diagnostic.
A/C REQUEST Ð Tech 2 Displays YES or NO Ð
Indicates the state of the A/C request input circuit from the
HVAC controls. The PCM uses the A/C request signal to
determine whether A/C compressor operation is being
requested.
AIR/FUEL RATIO Ð Tech 2 Range 0.0-25.5 Ð
Air/fuel ratio indicates the PCM commanded value. In
closed loop, the air/fuel ratio should normally be
displayed around ª14.2-14.7º. A lower air/fuel ratio
indicates a richer commanded mixture, which may be
seen during power enrichment or TWC protection modes.
A higher air/fuel ratio indicates a leaner commanded
mixture. This can be seen during deceleration fuel mode.
AP1 ÐTech 2 Range 0%-100% Ð
AP (accelerator pedal) angle is computed by the PCM
from the AP sensor voltage. AP angle should display
ª13%º at idle and ª85-89%º at wide open throttle.
AP2 ÐTech 2 Range 0%-100% Ð
AP (accelerator pedal) angle is computed by the PCM
from the AP sensor voltage. AP angle should display
ª85-89%º at idle and ª11-15%º at wide open throttle.
AP3 ÐTech 2 Range 0%-100% Ð
AP (accelerator pedal) angle is computed by the PCM
from the AP sensor voltage. AP angle should display
ª85-89%º at idle and ª32-36%º at wide open throttle.
BAROMETRIC PRESSURE Ð Tech 2 Range 10-105
kPa/0.00-5.00 Volts Ð
The barometric pressure reading is determined from the
MAP sensor signal monitored during key up and wide
open throttle (WOT) conditions. The barometric pressure
is used to compensate for altitude differences and is
normally displayed around ª61-104º depending on
altitude and barometric pressure.
CHECK TRANS LAMP Ð AUTO TRANSMISSION Ð
Indicates the need to check for a DTC with the Tech 2
when the lamp is flashing 0.2 seconds ON and 0.2
seconds OFF.
DESIRED EGR POS. Ð Tech 2 Range 0%-100% Ð
Represents the EGR pintle position that the PCM is
commanding.
DESIRED IDLE Ð Tech 2 Range 0-3187 RPM Ð
The idle speed that the PCM is commanding. The PCM
will compensate for various engine loads based on engine
coolant temperature, to keep the engine at the desired
speed.ECT Ð (Engine Coolant Temperature) Tech 2
Range ±40
C to 151
C (±40
F to 304
F) Ð
The engine coolant temperature (ECT) is mounted in the
coolant stream and sends engine temperature
information to the PCM. The PCM applies 5 volts to the
ECT sensor circuit. The sensor is a thermistor which
changes internal resistance as temperature changes.
When the sensor is cold (high resistance), the PCM
monitors a high signal voltage and interprets that as a cold
engine. As the sensor warms (decreasing resistance),
the voltage signal will decrease and the PCM will interpret
the lower voltage as a warm engine.
EGR DUTY CYCLE Ð Tech 2 Range 0%-100% Ð
Represents the EGR valve driver PWM signal from the
PCM. A duty cycle of 0% indicates that no EGR flow is
being commanded; a 100% duty cycle indicates
maximum EGR flow commanded.
EGR FEEDBACK Ð Tech 2 Range 0.00-5.00 Volts Ð
Indicates the EGR pintle position sensor signal voltage
being monitored by the PCM. A low voltage indicates a
fully extended pintle (closed valve); a voltage near 5 volts
indicates a retracted pintle (open valve).
ENGINE LOAD Ð Tech 2 Range 0%-100% Ð
Engine load is calculated by the PCM from engine speed
and MAF sensor readings. Engine load should increase
with an increase in RPM or air flow.
ENGINE RUN TIME Ð Tech 2 Range
00:00:00-99:99:99 Hrs:Min:Sec Ð
Indicates the time elapsed since the engine was started.
If the engine is stopped, engine run time will be reset to
00:00:00.
ENGINE SPEED Ð Range 0-9999 RPM Ð
Engine speed is computed by the PCM from the 58X
reference input. It should remain close to desired idle
under various engine loads with engine idling.
EVAP PURGE PWM Ð Tech 2 Range 0%-100% Ð
Represents the PCM commanded PWM duty cycle of the
EVAP purge solenoid valve. ª0%º displayed indicates no
purge; ª100%º displayed indicates full purge.
FUEL PUMP Ð Tech 2 Displays ON or OFF Ð
Indicates the PCM commanded state of the fuel pump
relay driver circuit.
HO2S BANK 1, SEN. 1
Ð Tech 2 Range 0-1132 mV Ð
Represents the fuel control exhaust oxygen sensor
output voltage. Should fluctuate constantly within a range
between 10 mV (lean exhaust) and 1000 mV (rich
exhaust) while operating in closed loop.
HO2S BANK 1, SEN. 2
Ð Tech 2 Range 0-1000mV Ð
Monitors the exhaust oxygen sensor output voltage. The
PCM monitors the operating efficiency of catalytic
converter by comparing the output voltages of sensor 1
and sensor 2 in this bank. If the catalytic converter is
operating efficiently, the output voltage of sensor 1 will
give a greater fluctuation than that of sensor 2. If the
PCM detects an abnormal level of voltage fluctuation
from sensor 2, a DTC P0420 will be set, indicating that the
catalytic converter for this bank is no longer operating
efficiently.

6E±77
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
HO2S BANK2, SEN. 1 ÐTech 2 Range 0-1132 mVÐ
Represents the fuel control exhaust oxygen sensor
output voltage. Should fluctuate constantly within a range
between 10mV (lean exhaust) and 1000 mV (rich
exhaust) while operating in closed loop.
HO2S BANK 2, SEN. 2ÐTech 2 Range 0-1000 mVÐ
Monitors the exhaust oxygen sensor output voltage. The
PCM monitors the operating efficiency of catalytic
converter by comparing the output voltages of sensor 1
and sensor 2 in this bank. If the catalytic converter is
operating efficiently, the output voltage of sensor 1 will
have a greater fluctuation than that of sensor 2. If the
PCM detects an abnormal level of voltage fluctuation
from sensor 2, a DTC P0430 will be set, indicating that the
catalytic converter for this bank is no longer operating
efficiently.
HO2S BANK 1, SEN. 1ÐTech 2 Displays NOT
READY or READYÐ
Indicates the status of the exhaust oxygen sensor. The
Tech 2 will indicate that the exhaust oxygen sensor is
ready when the PCM detects a fluctuating HO2S voltage
sufficient to allow closed loop operation. This will not
occur unless the exhaust oxygen sensor is warmed up.
HO2S BANK 2, SEN. 1 Ð Tech 2 Displays NOT
READY or READY Ð
Indicates the status of the exhaust oxygen sensor. The
Tech 2 will indicate that the exhaust oxygen sensor is
ready when the PCM detects a fluctuating HO2S voltage
sufficient to allow closed loop operation. This will not
occur unless the exhaust oxygen sensor is warmed up.
HO2S WARM UP TIME BANK 1, SEN. 1/BANK 1,
SEN 2/BANK 2 SEN. 1/BANK 2 SEN. 2 Ð Tech 2
Range 00:00:00-99:99:99 HRS:MIN:SEC Ð
Indicates warm-up time for each HO2S. The HO2S
warm-up time is used for the HO2S heater test. The PCM
will run the heater test only after a cold start (determined
by engine coolant and intake air temperature at the time
of start-up) and only once during an ignition cycle. When
the engine is started the PCM will monitor the HO2S
voltage. When the HO2S voltage indicates a sufficiently
active sensor, the PCM looks at how much time has
elapsed since start-up. If the PCM determines that tool
much time was required for the HO2S to become active,
a DTC will set. If the engine was warm when started,
HO2S warm-up will the display ª00:00:00º.
IAT (INTAKE AIR TEMPERATURE) Ð Tech 2 Range
±40
C to 151
C (±40
F to 304
F) Ð
The PCM converts the resistance of the intake air
temperature sensor to degrees. Intake air temperature
(IAT) is used by the PCM to adjust fuel delivery and spark
timing according to incoming air density.
IGNITION 1 Ð Tech 2 Range 0-25.5 Volts Ð
This represents the system voltage measured by the
PCM at its ignition feed.INJ. PULSE BANK 1/INJ. PULSE BANK 2 Ð Tech 2
Range 0-1000 msec. Ð
Indicates the amount of time the PCM is commanding
each injector ªONº during each engine cycle. A longer
injector pulse width will cause more fuel to be delivered.
Injector pulse width should increase with increased
engine load.
LONG TERM FUEL TRIM BANK 1/BANK 2 Ð
The long term fuel trim is derived from the short term fuel
trim values and represents a long term correction of fuel
delivery for the bank in question. A value of 0% indicates
that fuel delivery requires no compensation to maintain
the PCM commanded air/fuel ratio. A negative value
significantly below 0% indicates that the fuel system is
rich and fuel delivery is being reduced (decreased injector
pulse width). A positive value significantly greater than
0% indicates that a lean condition exists and the PCM is
compensating by adding fuel (increased injector pulse
width). Because long term fuel trim tends to follow short
term fuel trim, a value in the negative range due to
canister purge at idle should not be considered unusual.
Fuel trim values at maximum authority may indicate an
excessively rich or lean system.
Fuel System STATUS Ð Tech 2 Displays OPEN or
CLOSED Ð
ªCLOSEDº indicates that the PCM is controlling fuel
delivery according to oxygen sensor voltage. In ªOPENº
the PCM ignores the oxygen sensor voltage and bases
the amount of fuel to be delivered on TP sensor, engine
coolant, and MAF sensor inputs only.
MAF Ð Tech 2 Range 0.0-512 gm/s Ð
MAF (mass air flow) is the MAF input frequency
converted to grams of air per second. This indicates the
amount of air entering the engine.
MAP
Ð Tech 2 Range 10-105 kPa (0.00-4.97 Volts) Ð
The manifold absolute pressure (MAP) sensor measures
the change in the intake manifold pressure from engine
load, EGR flow, and speed changes. As intake manifold
pressure increases, intake vacuum decreases, resulting
in a higher MAP sensor voltage and kPa reading. The
MAP sensor signal is used to monitor intake manifold
pressure changes during the EGR flow test, to update the
BARO reading, and as an enabling factor for several of
the diagnostics.
MIL Ð Tech 2 Displays ON or OFF Ð
Indicates the PCM commanded state of the malfunction
indicator lamp.
MISFIRE CUR. CYL. #1 /#2 /#3 /#4 / #5 / #6 Ð Tech 2
Range 0-255 Counts Ð
The misfire current counters increase at a rate according
to the number of the possible misfires being detected on
each cylinder. The counters may normally display some
activity, but the activity should be nearly equal for all the
cylinders.

6E±79
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
3.5L V-6 Engine (Automatic and Manual Transmission)
Tech 2
Parameter
Data ListUnits DisplayedTypical Data
Values (IDLE)Typical Data
Values
(2500 RPM)Refer To
A/C Clutch
RelayEngineOn/OffOffOffGeneral Description and
Operation, A/C Clutch
Circuit Operation
A/C RequestEngineYes/NoNoNoGeneral Description and
Operation, A/C Request
Signal
Air/Fuel RatioEngineRatio: _ to 114.714.7General Description and
Operation, Fuel System
Metering Purpose
APP Sensor1EnginePercent11±1335±40General Description and
Operation
APP Sensor2EnginePercent87±8860±65General Description and
Operation
APP Sensor3EnginePercent87±8850±57General Description and
Operation
Barometric
PressureEnginekPa61-104
(depends on
altitude and
barometric
pressure)61-104
(depends on
altitude and
barometric
pressure)General Description and
Operation
Brake Light
SwitchEngineOpen 0V/Closed
12VOpen 0VOpen 0VRefer to Section 5
Check Trans
Lamp (Auto
Trans)EngineOn/OffOffOff4L30-E Automatic
Transmission Diagnosis
Cruise Main
SwitchEngineActive/InactiveInactiveInactiveRefer to Section 10
Cruise Set
SwitchEngineActive/InactiveInactiveInactiveRefer to Section 10
Cruise Cancel
SwitchEngineActive/InactiveInactiveInactiveRefer to Section 10
Cruise
Resume
SwitchEngineActive/InactiveInactiveInactiveRefer to Section 10
Decel Fuel
CutoffEngineActive/InactiveInactiveInactiveGeneral Description and
Operation, Deceleration
Mode
Desired EGR
PositionEnginePercent0%0%General Description and
Operation, EGR Pintle
Position Sensor
Desired Idle
SpeedEngineRPM750800General Description and
Operation
ECT (Engine
Coolant Temp)EngineDegrees C,
Degrees F80-100
C
(176-212
F)80-100
C
(176-212
F)General Description and
Operation, Engine
Coolant Temperature
(ECT) Sensor
EGR Closed
Pintle PositionEngineSteps20-4020-40General Description and
Operation, EGR Pintle
Position Sensor

6E±80
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Tech 2
ParameterRefer To Typical Data
Values
(2500 RPM) Typical Data
Values (IDLE) Units Displayed Data List
EGR Duty
CycleEnginePercent0%0%General Description and
Operation, Linear EGR
Operation and Results of
Incorrect Operation
EGR
FeedbackEngineVolts0.45-0.800.45-0.80Ð
EGR
NormalizedEnginePercent0%0%Ð
Engine LoadEnginePercent2.0% - 5.5%8.0% - 16.0%General Description and
Operation, Mass Air Flow
(MAF) Sensor
Time From
StartEngineSecVaries. Resets
at each engine
start.Varies. Resets
at each engine
start.
Ð
Engine SpeedEngineRPMWithin ±50 to
+100 of
ªDesired IdleºActual engine
speed
Ð
EVAP Purge
SolenoidEnginePercent0%0%Diagnosis, EVAP
Emission Canister Purge
Valve Check
EVAP Vent
ValveEngineOn/OffOffOffDiagnosis, EVAP Canister
Purge Solenoid and
EVAP Vacuum Switch
and Visual Check; DTCs:
P1441, P1442
Fuel System
StatusEngineOpen
Loop/Closed
LoopClosed LoopClosed LoopGeneral Description
Fuel LevelEnginePercentÐÐEngine Fuel
Fuel Level
SensorEngineVoltsÐÐEngine Fuel
Fuel Tank
(Vapor)EngineVolts1.02 ± 1.861.02 ± 2.57General Description and
Operation
Pressure
Sensorin. H2OÐÐ
Fuel PumpEngineOn/OffOnOnEngine Fuel
HO2S Bank 1
Sen.1
(millivolts)O2
Sensor
DataMillivolts50-950
changing
quickly50-950, always
changing
quicklyGeneral Description and
Operation, Fuel control
HO2S
HO2S Bank 1
Sen.2
(millivolts)
(Auto Trans)O2
Sensor
DataMillivolts200-700
changing slowly250-650
changing slowlyGeneral Description and
Operation, Fuel Metering
System
HO2S Bank 1
Sen.2
(millivolts)
(Manual
Trans)O2
Sensor
DataMillivolts50-950
changing
quickly50-950
changing
quicklyGeneral Description and
Operation, Fuel Metering
System
HO2S Bank 1
Sen.3
(millivolts)
(Manual
Trans)O2
Sensor
DataMillivolts200-700
changing slowly250-650
changing slowlyGeneral Description and
Operation, Catalyst
Monitor Heated Oxygen
Sensor (Manual Trans)

6E±82
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Tech 2
ParameterRefer To Typical Data
Values
(2500 RPM) Typical Data
Values (IDLE) Units Displayed Data List
Long Term FT
Bank 2 (Long
Term Fuel
Trim)MisfireCounts and
Percentage100 to 150
counts, ±22%
to +17%100 to 150
counts, ±22%
to +17%Diagnosis, Fuel Trim
System Monitor; DTCs:
P0171
MAF (Mass Air
Flow)EngineGrams per
second2.85-6.659.5-16.5General Description and
Operation, MAF; DTCs:
P101, P0102, P0103
MAP kPa
(Manifold
Absolute
EngineKilopascals23-4019-32General Description and
Operation, Manifold
Absolute Pressure (MAP)Absolute
Pressure)Volts0.65-1.320.46-1.10Absolute Pressure (MAP)
Sensor; DTCs: P0106,
P0107, P0108
MILEngineOn/OffOffOffOn-Board Diagnostic
System Check
Misfire Cur. Cyl
#1MisfireCounts0-20-2DTC P0300
Misfire Cur. Cyl
#2MisfireCounts0-20-2DTC P0300
Misfire Cur. Cyl
#3MisfireCounts0-20-2DTC P0300
Misfire Cur. Cyl
#4MisfireCounts0-20-2DTC P0300
Misfire Cur. Cyl
#5MisfireCounts0-20-2DTC P0300
Misfire Cur. Cyl
#6MisfireCounts0-20-2DTC P0300
Misfire Hist.
Cyl #1MisfireCounts00DTC P0300
Misfire Hist.
Cyl #2MisfireCounts00DTC P0300
Misfire Hist.
Cyl #3MisfireCounts00DTC P0300
Misfire Hist.
Cyl #4MisfireCounts00DTC P0300
Misfire Hist.
Cyl #5MisfireCounts00DTC P0300
Misfire Hist.
Cyl #6MisfireCounts00DTC P0300
Misfire Failures
Since First FailMisfireCounts00DTC P0300
Misfire Passes
Since First FailMisfireCounts00DTC P0300
PNP
(Park/Neutral
Position)EngineP-N /
R-D-3-2-LP-NP-N4L30-E Automatic
Transmission Diagnosis
Power
EnrichmentEngineNO/YESNONOGeneral Description and
Operation, Acceleration
Mode
PSP Switch
(Power
Steering
Pressure)EngineNormal/HiNormal
PressureNormal
PressureRefer to 2A Section