checking oil ISUZU AXIOM 2002 Service Repair Manual

0B±5 MAINTENANCE AND LUBRICATION
Explanation of Complete Vehicle
Maintenance Schedule
Brief explanations of the services listed in the preceding
Maintenance Schedule are presented below.
Replace all questionable parts and note any necessary
repairs as you perform these maintenance procedures.
Front and Rear Axle Lubricant
Replacement
Check the lubricant level after every 7,500 miles (12,000
km) of operation and add lubricant to level of filler hole if
necessary.
Replace the front and rear axle lubricant at 15,000 miles
(24,000 km) and 30,000 miles (48,000 km) and after
every 30,000 miles (48,000 km) of operation thereafter.
Air Cleaner Element Replacement
Replace the air cleaner under normal operating
conditions every 30,000 miles (48,000 km).
Operation of the vehicle in dusty areas will necessitate
more frequent replacement.
Spark Plug Replacement
Replace the plugs at 100,000 miles (160,000 km)
intervals with the type specified at the end of this section.
Cooling System Service
Drain, flush and refill system with new engine coolant.
Refer to
ªRecommended Fluids and Lubricantsº in this
section, or ENGINE COOLING (SEC.6B).
Timing Belt Replacement
Replacement of the timing belt is recommended at every
100,000 miles (160,000 km).
Failure to replace the timing belt may result in serious
damage to the engine.
Valve Clearance Adjustment
Incorrect valve clearance will result in increased engine
noise and reduced engine output.
Retorque the camshaft bracket bolts before checking and
adjusting the valve clearance.
Check and adjust the valve clearance whenever
increased engine noise is heard.
Tire Rotation
Rotate tires every 7,500 miles (12,000 km).
Front Wheel Bearings Lubricant
Replacement (Vehicles Produced Before
July/31/2001)
Clean and repack the front wheel bearings at 30,000
miles (48,000 km) intervals.
Refer to DRIVE SHAFT SYSTEM (SEC. 4C).
Front Wheel Bearings Check (Vehicles
Produced After Aug./1/2001)
Inspect hub unit bearing at every 60,000 miles (96,000
km).
If there is abnormal condition, replace hub unit bearing.
Radiator Core and Air Conditioning
Condenser Cleaning
Clean the front of the radiator core and air conditioning
condenser, at 60,000 miles (96,000 km) intervals.
Fluid Level Check
A fluid loss in any system (except windshield
washer) may indicate a problem. Repair the system
at once.
Engine oil level
Check level and add if necessary. The best time to check
the engine oil level is when the oil is warm. After stopping
the engine with the vehicle on a level surface, wait a few
minutes for the oil to drain back to the oil pan. Pull out the
oil level indicator (dipstick). Wipe it clean and push the oil
level indicator back down all the way. Pull out the oil level
indicator, keeping the tip down, and look at the oil level on
it.
Add oil, if needed, to keep the oil level above the ªADDº
mark and between the ªADDº and ªFULLº marks in the
operating range area. Avoid overfilling the engine since
this may cause engine damage. Push the oil level
indicator back down all the way after taking the reading.
If you check the oil level when the oil is cold, do not run the
engine first. The cold oil will not drain back to the pan fast
enough to give a true oil level.
Engine coolant level and condition
Check engine coolant level in the coolant reservoir and
add engine coolant if necessary. Inspect the engine
coolant and replace it if dirty or rusty.
Windshield washer fluid level
Check washer fluid level in the reservoir and add if
necessary.
Power steering system reservoir level
Check and keep at the proper level.
Brake master cylinder reservoir level
Check fluid. Keep fluid at proper level. A low fluid level can
indicate worn disc brake pads which may need to be
serviced.
Hydraulic clutch system
Check fluid level in the reservoir. Add fluid as required.
Battery fluid level
Check fluid level in the battery.
Fluid Leak Check
Check for fuel, water, oil or other fluid leaks by looking at
the surface beneath the vehicle after it has been parked
for a while. Water dripping from the air conditioning
system after use is normal. If you notice gasoline fumes or
fluid at any time, locate the source and correct it at once.
Engine Oil and Oil Filter Replacement
Always use API SE, SF, SG, SH or ILSAC GF±1 quality
oils of the proper viscosity.
When choosing an oil, consider the range of
temperatures the car will be operated in before the next oil
change. Then, select the recommended oil viscosity from
the chart.

1A±2
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
Compressor 1A±53. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Precaution 1A±53. . . . . . . . . . . . . . . . . . . .
General Description 1A±53. . . . . . . . . . . . . . . . . . . . . .
Diagnosis 1A±54. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Magnetic Clutch Assembly (DKV-14G Type) 1A±55
Parts Location View 1A±55. . . . . . . . . . . . . . . . . . . .
Removal 1A±55. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 1A±57. . . . . . . . . . . . . . . . . .
Installation 1A±57. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compressor Oil 1A±59. . . . . . . . . . . . . . . . . . . . . . . . .
Oil Specification 1A±59. . . . . . . . . . . . . . . . . . . . . . .
Handling of Oil 1A±59. . . . . . . . . . . . . . . . . . . . . . . .
Compressor Oil Check 1A±59. . . . . . . . . . . . . . . . .
Checking and Adjusting Oil Quantity for
Used Compressor 1A±59. . . . . . . . . . . . . . . . . . . . .
Checking and Adjusting for Compressor
Replacement 1A±60. . . . . . . . . . . . . . . . . . . . . . . . .
Contamination of Compressor Oil 1A±60. . . . . . . .
Oil Return Operation 1A±60. . . . . . . . . . . . . . . . . . .
Replacement of Component Parts 1A±60. . . . . . .
Main Data and Specifications 1A±61. . . . . . . . . . . . .
Special Tools 1A±63. . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Air Conditioning System 1A±64. . . . . . . .
General Description 1A±64. . . . . . . . . . . . . . . . . . . . . .
Automatic Air Conditioner Parts
Configuration 1A±64. . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Diagram 1A±65. . . . . . . . . . . . . . . . . . . . . . .
Functions and Features 1A±70. . . . . . . . . . . . . . . .
Automatic Air Conditioner Block Diagram 1A±71.
Control Panel Layout 1A±72. . . . . . . . . . . . . . . . . . .
Air Control Functions 1A±73. . . . . . . . . . . . . . . . . . .
Control Panel Switch Operation 1A±74. . . . . . . . .
Overview of Construction, Movement and
Control of Major Parts of Automatic Air
Conditioner System 1A±77. . . . . . . . . . . . . . . . . . .
Overview of Automatic Control of Automatic
Air Conditioner 1A±81. . . . . . . . . . . . . . . . . . . . . . .
Automatic Air Conditioning System 1A±82. . . . . .
Troubleshooting 1A±86. . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting, Its Overview and
Procedures 1A±86. . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Air Conditioner Control Unit Power
Supply Diagnosis 1A±87. . . . . . . . . . . . . . . . . . . . . Performance and Movement checklist for
Automatic Air Conditioner Related Parts 1A±89.
Troubleshooting With Self-Diagnosis
Function 1A±91. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection By Failed Location 1A±97. . . . . . . . . . . . .
Inspection of the Sensors 1A±97. . . . . . . . . . . . . . .
Inspection of the Intake Actuator System 1A±101.
Inspection of the Mix Actuator System 1A±104. . . .
Inspection of the Mode Actuator System 1A±107. .
Inspection of the Fan Motor System 1A±110. . . . . .
Inspection of the Magnetic Clutch System 1A±115
Individual Inspection 1A±118. . . . . . . . . . . . . . . . . . .
On-Vehicle Service 1A±121. . . . . . . . . . . . . . . . . . . . . .
Power Transistor 1A±121. . . . . . . . . . . . . . . . . . . . . .
Removal 1A±121. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 1A±121. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Heater/Air Conditioner Control
Unit 1A±121. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 1A±121. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 1A±121. . . . . . . . . . . . . . . . . . . . . . . . . . . .
In Car Sensor 1A±122. . . . . . . . . . . . . . . . . . . . . . . . .
Removal 1A±122. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 1A±122. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ambient Sensor 1A±122. . . . . . . . . . . . . . . . . . . . . . .
Removal 1A±122. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 1A±122. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sun Sensor 1A±123. . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 1A±123. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 1A±123. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Duct Sensor 1A±123. . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 1A±123. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 1A±123. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode Actuator 1A±124. . . . . . . . . . . . . . . . . . . . . . . .
Removal 1A±124. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 1A±124. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mix Actuator 1A±124. . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 1A±124. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 1A±124. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intake Actuator 1A±125. . . . . . . . . . . . . . . . . . . . . . . .
Removal 1A±125. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 1A±125. . . . . . . . . . . . . . . . . . . . . . . . . . . .

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±33
Leak Check
Inspection of refrigerant leak
Refrigerant leak may cause an adverse effect not only on
the performance and durability of each component of the
air±conditioner, but also on the global atmosphere.
Therefore, it is most important to repair refrigerant leak
when there is any leak found.
Inspection flow of refrigerant leak
StepActionYe sNo
11. Evacuate the refrigerant system.
2. Charge the refrigerant.
Is there any refrigerant leak?
Repair refrigerant
system.
Go to Step 2
21. Operate the compressor for more than 5 minutes to raise the
pressure on the high pressure side.
Is there any refrigerant leak at high pressure components?
Repair refrigerant
system.
Compressor
operation to be
confirmed.
Inspection Steps
Check the components of air±conditioner to see if there
occurs any refrigerant leak along the flow of refrigerant.
NOTE:

To avoid refrigerant leak detection error, avoid
refrigerant vapor and cigarette smoke presence when
performing the inspection. Also, select a location that
is not susceptible to wind, in case refrigerant vapor is
found it will not be blown off.

Inspection should be conducted chiefly on the pipe
connections and sections where a marked oil
contamination is found. When refrigerant is leaking,
oil inside is also leaking at the same time.

It is possible to visually check the leak from inside the
cooling unit. Follow the method below when
performing the inspection. Remove the drain hose or
resistor of the cooling unit, and insert a leak detector
to see if there are signs of leakage.
High Pressure Side
1. Discharger section of compressor.
2. Inlet/outlet section of condenser.
3. Inlet/outlet section of receiver driver.
4. Inlet section of cooling unit.
Low Pressure Side
1. Outlet section of cooling unit.
2. Intake section of compressor.
Major Checking Points of Refrigerant Leak
Compressor

Pipe connection

Sealing section of shaft

Mating section or cylinder
Condenser

Pipe connection

Welds of condenser bodyReceiver driver

Pipe connection

Attaching section of pressure switch

Section around the sight glass
Evaporator unit (cooling unit)

Pipe connections

Connections of expansion valve

Brazed sections of evaporator
NOTE:

The evaporator and expansion valve are contained in
the case. Remove the drain hose or the resistor of the
cooling unit and insert a leak detector when checking
for any leak.
Flexible hose

Pipe connection

Caulking section of the hose

Hose (cracks, pinholes, flaws)
Pipe

Pipe connection

Pipe (cracks, flaws)
Charge valve
NOTE:

The charge valve, which is used to connect the gauge
manifold, is normally provided with a resin cap. When
the valve inside gets deteriorated, refrigerant will leak
out.Leak at Refrigerant Line Connections
1. Check the torque on the refrigerant line fitting and, if
too loose, tighten to the specified torque.

Use two wrenches to prevent twisting and damage
to the line.

Do not over tighten.
2. Perform a leak test on the refrigerant line fitting.

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±59
Compressor Oil
Oil Specification

The HFC-134a system requires a synthetic (PAG)
compressor oil whereas the R-12 system requires a
mineral compressor oil. The two oils must never be
mixed.

Compressor (PAG) oil varies according to
compressor model. Be sure to use oil specified for the
model of compressor.

Always use HFC-134a Vane Rotary Type
Compressor Oil (AIPDN Part No.2-90188-301-0)
Handling of Oil

The oil should be free from moisture, dust, metal
powder, etc.

Do not mix with other oil.

The water content in the oil increases when exposed
to the air. After use, seal oil from air immediately.
(HFC-134a Vane Rotary Compressor Oil absorbs
moisture very easily.)

The compressor oil must be stored in steel
containers, not in plastic containers.
Compressor Oil Check
The oil used to lubricate the compressor is circulating with
the refrigerant.
Whenever replacing any component of the system or a
large amount of gas leakage occurs, add oil to maintain
the original amount of oil.
Oil Capacity
Capacity total in system: 150cc (5.0 fl.oz)
Compressor (Service parts) charging amount:
150 cc (5.0 fl.oz)
Checking and Adjusting Oil Quantity
for Used Compressor
1. Perform oil return operation. Refer to Oil Return
Operation in this section.
2. Discharge and recover refrigerant and remove the
compressor.
3. Drain the compressor oil and measure the extracted
oil with a measuring cylinder.
4. If the amount of oil drained is much less than 90 cc
(3.0 fl. oz.), some refrigerant may have leaked out.
Conduct a leak tests on the connections of each
system, and if necessary, repair or replace faulty
parts.
5. Check the compressor oil contamination. (Refer to
Contamination of Compressor Oil in this section.)
6. Adjust the oil level following the next procedure
below.(Charging Amount)
(Collected Amount)
more than 90cc (3.0
fl.oz)same as collected
amount
less than 90 cc (3.0 fl.oz)90cc (3.0 fl.oz)
7. Install the compressor, then evacuate, charge and
perform the oil return operation.
8. Check system operation.
When it is impossible to preform oil return operation,
the compressor oil should be checked in the
following order:
1. Discharge and recover refrigerant and remove the
compressor.
2. Drain the compressor oil and measure the extracted
oil with a measuring cylinder.
3. Check the oil for contamination.
4. If more than 90 cc (3.0 fl. oz.) of oil is extracted from
the compressor, supply the same amount of oil to the
compressor to be installed.
5. If the amount of oil extracted is less than 90 cc (3.0 fl.
oz.), recheck the compressor oil in the following
order.
6. Supply 90 cc (3.0 fl. oz.) of oil to the compressor and
install it onto the vehicle.
7. Evacuate and recharge with the proper amount of
refrigerant.
8. Perform the oil return operation.
9. Remove the compressor and recheck the amount of
oil.
10. Adjust the compressor oil, if necessary.
(Collected Amount)
(Charging Amount)
more than 90 cc (3.0
fl.oz)same as collected
amount
less than 90 cc (3.0 fl.oz)90 cc (3.0 fl.oz)

1A±60
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
Checking and Adjusting for
Compressor Replacement
150 cc (5.0 fl.oz.) of oil is charged in compressor (service
parts). So it is necessary to drain the proper amount of oil
from the new compressor.
1. Perform oil return operation.
2. Discharge and recover the refrigerant and remove the
compressor.
3. Drain the compressor oil and measure the extracted
oil.
4. Check the compressor oil for contamination.
5. Adjust the oil level as required.
(Amount of oil drained
from used compressor)
(Draining amount of oil
from new compressor)
less than 90 cc (3.0 fl.oz)Same as drained
amount
more than 90 cc (3.0
fl.oz)90 cc (3.0 fl.oz)
6. Evacuate, charge and perform the oil return
operation.
7. Check the system operation.
Contamination of Compressor Oil
Unlike engine oil, no cleaning agent is added to the
compressor oil. Even if the compressor runs for a long
period of time (approximately one season), the oil never
becomes contaminated as long as there is nothing wrong
with the compressor or its method of use.
Inspect the extracted oil for any of the following
conditions:

The capacity of the oil has increased.

The oil has changed to red.

Foreign substances, metal powder, etc., are present
in the oil.
If any of these conditions exists, the compressor oil
is contaminated. Whenever contaminated
compressor oil is discovered, the receiver/drier must
be replaced.
Oil Return Operation
There is close affinity between the oil and the refrigerant.
During normal operation, part of the oil recirculates with
the refrigerant in the system. When checking the amount
of oil in the system, or replacing any component of the
system, the compressor must be run in advance for oil
return operation. The procedure is as follows:
1. Open all the doors and the engine hood.
2. Start the engine and air conditioning switch to ªONº
and set the fan control knob at its highest position.
3. Run the compressor for more than 20 minutes
between 800 and 1,000 rpm in order to operate the
system.
4. Stop the engine.
Replacement of Component Parts
When replacing the system component parts, supply the
following amount of oil to the component parts to be
installed.
(Component parts to be
installed)
(Amount of Oil)
Evaporator 50 cc (1.7 fl. oz.)
Condenser30 cc (1.0 fl. oz.)
Receiver/dryer30 cc (1.0 fl. oz.)
Refrigerant line (one
piece)10 cc (0.3 fl. oz.)

POWER±ASSISTED STEERING SYSTEM2A±11
4. Bleed the system. Refer to Bleeding the Power
Steering System
in this section.
5. Start the engine and check the fluid level. Add power
steering fluid if required. When the engine is at
normal operating temperature, increase engine
speed to 1500 rpm.
CAUTION: Do not leave shutoff valve fully closed
for more than 5 seconds, as the pump could become
damaged internally.
6. Fully close the shutoff valve. Record the highest
pressures.

If the pressure recorded is within 9300±9800 kPa
(1350±1420 psi), the pump is functioning within its
specifications.

If the pressure recorded is higher than 9800 kPa
(1420 psi), the valve in the pump is defective.

If the pressure recorded is lower than 9300 kPa
(1350 psi), the valve or the rotating group in the
pump is defective.
7. If the pump pressures are within specifications, leave
the valve open and turn (or have someone else turn)
the steering wheel fully in both directions. Record the
highest pressures and compare with the maximum
pump pressure recorded in step 6. If this pressure
cannot be built in either side of the power steering
unit, the power steering unit is leaking internally and
must be replaced.
8. Shut the engine off, remove the testing gauge.
9. Reconnect the pressure hose, check the fluid level
and make the needed repairs.
10. If the problem still exists, the steering and front
suspension must be thoroughly examined.
Maintenance
The hydraulic system should be kept clean and fluid level
in the reservoir should be checked at regular intervals and
fluid added when required. Refer to
Recommended
Fluids and Lubricants in General Information
section for
the type of fluid to be used and the intervals for filling.
If the system contains some dirt, flush it as described in
this section. If it is exceptionally dirty, the pump must be
completely disassembled before further usage. (The
steering unit cannot be disassembled.)
All tubes, hoses, and fittings should be inspected for
leakage at regular intervals. Fittings must be tight. Make
sure the clips, clamps and supporting tubes and hoses
are in place and properly secured.
Power steering hoses and lines must not be twisted,
kinked or tightly bent. Air in the system will cause spongy
action and noisy operation. When a hose is disconnected
or when fluid is lost, for any reason, the system must be
bled after refilling. Refer to
Bleeding the Power Steering
System
in this section.

Inspect belt for tightness.

Inspect pulley for looseness or damage. The pulley
should not wobble with the engine running.

Inspect hoses so they are not touching any other
parts of the vehicle.

Inspect fluid level and fill to the proper level.
Fluid Level
1. Run the engine until the power steering fluid reaches
normal operating temperature, about 55
C (130
F),
then shut the engine off.
2. Check the level of fluid in the reservoir.
3. If the fluid level is low, add power steering fluid as
specified in General Information to the proper level
and install the receiver cap.
4. When checking the fluid level after the steering
system has been serviced, air must be bled from the
system. Refer to
Bleeding the Power Steering
System
in this section.
Bleeding The Power Steering System
When a power steering pump or unit has been installed,
or an oil line has been disconnected, the air that has
entered the system must be bled out before the vehicle is
operated. If air is allowed to remain in the power steering
fluid system, noisy and unsatisfactory operation of the
system may result.
Bleeding Procedure
When bleeding the system, and any time fluid is added to
the power steering system, be sure to use only power
steering fluid as specified in General Information.
1. Fill the pump fluid reservoir to the proper level and let
the fluid settle for at least two minutes.
2. Start the engine and let it run for a few seconds. Do
not turn the steering wheel. Then turn the engine off.
3. Add fluid if necessary.
4. Repeat the above procedure until the fluid level
remains constant after running the engine.
5. Raise and support the front end of the vehicle so that
the wheels are off the ground.
6. Start the engine. Slowly turn the steering wheel right
and left, lightly contacting the wheel stops.
7. Add power steering fluid if necessary.
8. Lower the vehicle, set the steering wheel at the
straight forward position after turning it to its full steer
positions 2 or 3 times, and stop the engine.
9. Check the fluid level and refill as required.
10. If the fluid is extremely foamy, allow the vehicle to set
a few minutes, then repeat the above procedure.
Flushing The Power Steering System
1. Raise and support the front end of the vehicle off the
ground until the wheels are free to turn.
2. Remove the fluid return line at the pump inlet
connector and plug the connector port on the pump.
Position the line toward a large container to catch the
draining fluid.
3. While running the engine at idle, fill the reservoir with
new power steering fluid. Turn the steering wheel in
both directions. Do not contact or hold the steering
wheel to the wheel stops. This will cause the pump to
go to pressure relief mode, which may cause a
sudden fluid overflow at the reservoir.

DIFFERENTIAL (REAR)4A2±23
Backlash Adjustment
1. Install the differential case assembly and bearing
caps.
2. Rotate the case several times to seat the bearings.
3. Remove the spreader.
4. Install the side bearing cap bolts.
Tighten side bearing cap bolts
Torque: 108 N´m (80 lb ft)
5. Install a dial indicator to the case using a magnetic
base.
6. Place the indicator stem at the heel end of a tooth.

Set the dial indicator so that the stem is in line with
the gear rotation and perpendicular to the tooth
angle.
425RS087
7. Check and record the backlash at three points around
the ring gear.

The pinion must be held stationary when checking
backlash.

The backlash should be the same at each point
within 0.07 mm (0.003 in). If the backlash varies
more than 0.07 mm (0.003 in), check for burrs, a
distorted case flange, or uneven bolting conditions.
8. Backlash at the minimum lash point measured should
be between 0.13 and 0.20 mm (0.005 and 0.008 in)
for all new gear sets.
9. If the backlash is not within specifications, move the
ring gear in or out from the pinion by increasing the
thickness of one shims, and decreasing the thickness
of the other shim by the same amount.
This will maintain the correct rear axls side bearing
preload.

Moving 0.05 mm (0.002 in) worth of shim from one
side of the differential to the other will change the
backlash adjustment by 0.03 mm (0.001 in).
10. After obtaining correct tooth contact described in
later, install ABS speed sensor.11. Install the cover with sealant.
Torque: 40 N´m (30 lb ft)
12. Fill the axle lubricant.
Gear Tooth Pattern Check
Checking the ring gear to pinion tooth pattern is to be
done only after setting up the axle according to the
methods in this section. The pattern check is NEVER to
be used as an initial check, or instead of checking pinion
depth and backlash adjustments.
This check is only to be verify the correct adjustment of
the gear set after set up.
425RS038
Legend
(1) Heel
(2) Toe
(3) Concave Side (Coast)
(4) Convex Side (Drive)
1. Wipe all oil out of the carrier, and carefully clean each
tooth of the ring gear.
2. Use gear marking compound 1052351 or equivalent
and apply this mixture sparingly to all ring gear teeth,
using a medium-stiff brush. When properly used, the
area of pinion tooth contact will be visible when hand
load is applied.
3. Tighten the bearing cap bolts to the specified torque.
4. Expand the brake shoes until a torque of 54 to 68 N´m
(40 to 50 lb ft.) is required to turn the pinion. A test
made without loading the gears will not give a
satisfactory pattern. Turn the pinion flange with a
wrench so that the ring gear rotates one full
revolution, then reverse the rotation so that the ring
gear rotates one revolution in the opposite direction.
5. Observe the pattern on the ring gear teeth and
compare this with figure.

4B2±1
DRIVE LINE CONTROL SYSTEM (TOD)
AXIOM
DRIVELINE/AXLE
DRIVELINE CONTROL SYSTEM (TOD)
CONTENTS
Service Precaution 4B2±1. . . . . . . . . . . . . . . . . . . . . .
General Description 4B2±2. . . . . . . . . . . . . . . . . . . . .
Transfer Position and Drive Mode 4B2±2. . . . . . . .
TOD Control 4B2±3. . . . . . . . . . . . . . . . . . . . . . . . . .
TOD Indicator Control 4B2±3. . . . . . . . . . . . . . . . . .
Abbreviations 4B2±3. . . . . . . . . . . . . . . . . . . . . . . . .
System Components 4B2±4. . . . . . . . . . . . . . . . . . . .
Parts Location 4B2±4. . . . . . . . . . . . . . . . . . . . . . . .
Front and Rear Speed Sensors 4B2±5. . . . . . . . . .
Electromagnetic Coil 4B2±5. . . . . . . . . . . . . . . . . . .
Multi Plate Disk Clutch Pack 4B2±5. . . . . . . . . . . .
Mechanical Lock Sleeve 4B2±5. . . . . . . . . . . . . . . .
High-Low Planetary Gear Set 4B2±6. . . . . . . . . . .
4H and 4L Switch 4B2±6. . . . . . . . . . . . . . . . . . . . . .
Transfer Connector (12-pin type) 4B2±6. . . . . . . .
Transfer Connector (8-pin type) 4B2±6. . . . . . . . .
TOD Indicator Lamps
(on the instrument panel) 4B2±7. . . . . . . . . . . . . .
Check Lamp 4B2±7. . . . . . . . . . . . . . . . . . . . . . . . . .
TOD ECU 4B2±8. . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-Low Shift Motor 4B2±9. . . . . . . . . . . . . . . . . . .
Motor Position and Encoder Position Code 4B2±10
Encode Position Plate 4B2±10. . . . . . . . . . . . . . . . . .
Shift High Range and Low Range 4B2±10. . . . . . . . Functions of TOD Switch and Indicator
Lamp 4B2±11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOD Switch and Indication of Drive Mode 4B2±11.
Check Lamp 4B2±13. . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis 4B2±14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Information Diagnosis 4B2±14. . . . . . . . . .
Self-diagnosis 4B2±14. . . . . . . . . . . . . . . . . . . . . . . . .
Precautions on Diagnosis 4B2±16. . . . . . . . . . . . . . .
Basic Diagnostic Flow Chart 4B2±18. . . . . . . . . . . . . .
Parts Location 4B2±19. . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Diagram 4B2±20. . . . . . . . . . . . . . . . . . . . . . . . .
Connector List 4B2±24. . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Failed Pin 4B2±26. . . . . . . . . . . . . . . . . . . . .
Connector Pin Assignment 4B2±26. . . . . . . . . . . . . .
Reference 4B2±28. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Failed TOD Control Unit Pin 4B2±30. . . . .
Tech 2 Scan Tool 4B2±32. . . . . . . . . . . . . . . . . . . . . .
Getting Started 4B2±33. . . . . . . . . . . . . . . . . . . . . . . .
Operating Procedure 4B2±33. . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Codes 4B2±35. . . . . . . . . . . . . . . .
Diagnosis from Trouble Codes 4B2±36. . . . . . . . . . . .
Trouble Diagnosis Depending on The Status
of TOD Indicator 4B2±67. . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis from Symptom 4B2±102. . . . . . . . . . . . . . . . .
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.

5A±33
BRAKE CONTROL SYSTEM
Chart A-5, TA-5 Braking Sound (From EHCU) Is Heard While Not Braking
StepActionYe sNo
1Is this the first vehicle start after engine start?Normal.
(It is self
checking sound.)
Go to Step 2
2Is vehicle speed under 10 km/h (6 mph)?Normal.
(It is self
checking sound.)
Go to Step 3
3Check for the following condition:

At the time of shift down or clutch operation.

At the time of low road friction drive (ice or snow road) or rough
road drive.

At the time of high-speed turn.

At the time of passing curb.

At the time of operating electrical equipment switches.

At the time of racing the engine (over 5000 rpm).
Did it occur under any one condition above?
ABS may
sometimes be
actuated even
when brake pedal
is not applied.
Go to Step 4
4Is there play in each or any sensor/wheel speed sensor rings?Repair.
Go to
Step 7Go to Step 5
5Damage or powdered iron sticking to each or any sensor/wheel
speed sensor ring?Repair.
Go to
Step 7Go to Step 6
6Is each sensor output normal? (Refer to Chart C-1 or TC-1).Check harness/
connector for
suspected
disconnection
If no
disconnection is
found, replace
Coil integrated
module.
Go to
Step 7
Repair.
Go to
Step 7
7Reconnect all components, ensure all components are properly
mounted.
Was this step finished?Repeat the ªBasic
diagnostic flow
chartº
Go to Step 7

5C±23 POWER±ASSISTED BRAKE SYSTEM
Functional Inspection of Master Cylinder
Piston
Push the primary piston (1) with your fingers to check that
it travels smoothly. If the motion is questionable, replace
the master cylinder as a complete assembly.
330RW007
Functional Inspection of Master Cylinder
Inspect the master cylinder for functionality described
below. Replace if necessary.
Install the primary piston holder (3) J±39242 (including
the master cylinder attachment (5) and master cylinder
plug (7)) onto the master cylinder (4). Make sure the
spacer (2) (2 bolts) with its adjusting bolt is screwed in up
to the ª0º line
330RW008Connect the master cylinder attachment (5) J±39242 with
the end of the radiator cap tester (6) J±24460±01, and
apply air pressure with the cap tester. Make sure there is
no rise in pressure while adjusting the bolt to the ª5º line.
There should be a pressure increase of 0.5 kg/cm
2 or
more.
330RW009
NOTE: When checking the front (or primary) side, be
sure to mount the master cylinder plug in the rear (or
secondary) port.
ª0º Lineª5º Line
Apply air
pressure to the
front and rear
portsNo pressure
rise.Pressure
increase of 0.5
kg/cm
2 or more
RemarksChecks port
into the
atmospheric
pressure
chamberChecks air
tightness of the
pressure cham-
ber
NOTE:
1. Do not use an air compressor, as the air from the
compressor is mixed with compressor oil.
2. When installing the master cylinder onto the vacuum
booster, always adjust the vacuum booster push rod.
(Refer to
Vacuum Booster in this section).
3. After the master cylinder is installed onto the vehicle,
check for leakage, pedal travel and pedal free play.
Installation
1. Install spacer and the 2 gaskets.
2. Install master cylinder.
When replacing the master cylinder or vacuum
booster or both, always measure the vacuum booster
push rod protrusion and adjust it as necessary (Refer
to
Vacuum Booster in section).
3. Install P&B valve and bracket.
4. Install 2 attaching nuts and tighten the attaching nuts
to the specified torque.
Torque: 13 N´m (113 lb in)