front axle shaft ISUZU AXIOM 2002 Service Repair Manual

SECTION TABLE OF CONTENTS
GENERAL INFORMATION
0AGeneral Information
0BMaintenance and Lubrication
WORKSHOP MANUAL
HEATING, VENTILATION AND AIR
CONDITIONING
1AHVAC System
STEERING
2APower-Assisted System
AXIOM
(UPR/S)SUSPENSION
3CFront Suspension
3DRear Suspension
3EWheel and Tire System
3FIntelligent Suspension System
DRIVELINE/AXLE
4A1Differential (Front)
4A2Differential (Rear)
4B1Driveline Control System
4B2Driveline Control System (TOD)
4CDrive Shaft System
4D2Transfer Case (TOD)
FOREWORD
This manual includes special notes, impor tant points, service data,
precautions, etc. That are needed for the maintenance, adjustments,
service, removal and installation of vehicle components.
All information, illustrations and specifications contained in this manual
are based on the latest product information available at the time of
publication.
All rights are reserved to make changes at any time without notice.
Arrangement of the material is shown in the table of contents on the
right-hand side of this page. A black spot on the first page of each
section can be seen on the edge of the book below each section title.
These point to a more detailed table of contents preceding each
section.BRAKE
5ABrake Control System
5BAnti-Lock Brake System
5CPower-Assisted Brake System
5D1Parking Brake System (4´4 model)
5D2Parking Brake System (4´2 model)
ENGINE
6AEngine Mechanical
6BEngine Cooling
6CEngine Fuel
6D1Engine Electrical
6D2Ignition System
6D3Starting and Charging System
6EDriveability and Emissions
6FEngine Exhaust
6GEngine Lubrication
6HEngine Speed Control System
6JInduction
TRANSMISSION
7AAutomatic Transmission
7A1Transmission Control System
BODY AND ACCESSORIES
8ALighting System
8BWiper/Washer System
This manual applies to 2002 models.8CEnter tainment
8DWiring System
8EMeter and Gauge
8FBody Structure
8GSeats
8HSecurity and Locks
8ISun Roof/Convertible Top
8JExterior/Interior Trim
RESTRAINTS
9ASeat Belt System
9JSupplemental Restraint System (Air Bag System)
9J1Restraint Control System
CONTROL SYSTEM
10ACruise Control System

0A±12
GENERAL INFORMATION
Abbreviations Charts
List of automotive abbreviations which may be used
in this manual
A Ð Ampere(s)
ABS Ð Antilock Brake System
AC Ð Alternating Current
A/C Ð Air Conditioning
ACCEL Ð Accelerator
ACC Ð Accessory
ACL Ð Air Cleaner
Adj Ð Adjust
A/F Ð Air Fuel Ratio
AIR Ð Secondary Air Injection System
Alt Ð Altitude
AMP Ð Ampere(s)
ANT Ð Antenna
ASM Ð Assembly
A/T Ð Automatic Transmission/Transaxle
ATDC Ð After Top Dead Center
ATF Ð Automatic Transmission Fluid
Auth Ð Authority
Auto Ð Automatic
BARO Ð Barometric Pressure
Bat Ð Battery
B+ Ð Battery Positive Voltage
Bbl Ð Barrel
BHP Ð Brake Horsepower
BPT Ð Backpressure Transducer
BTDC Ð Before Top Dead Center

C Ð Degrees Celsius
CAC Ð Charge Air Cooler
Calif Ð California
cc Ð Cubic Centimeter
CID Ð Cubic Inch Displacement
CKP Ð Crankshaft Position
CL Ð Closed Loop
CLCC Ð Closed Loop Carburetor Control
CMP Ð Camshaft Position
CO Ð Carbon Monoxide
Coax Ð Coaxial
Conn Ð Connector
Conv Ð Converter
Crank Ð Crankshaft
Cu. In. Ð Cubic Inch
CV Ð Constant Velocity
Cyl Ð Cylinder(s)
DI Ð Distributor Ignition
Diff Ð Differential
Dist Ð Distributor
DLC Ð Data Link Connector
DOHC Ð Double Overhead Camshaft
DTC Ð Diagnostic Trouble Code
DTM Ð Diagnostic Test Mode
DTT Ð Diagnostic Test Terminal
DVM Ð Digital Voltmeter (10 meg.)
DVOM Ð Digital Volt Ohmmeter
EBCM Ð Electronic Brake Control Module
ECM Ð Engine Control Module
ECT Ð Engine Coolant Temperature
EEPROM Ð Electronically Erasable Programmable
Read Only Memory
EGR Ð Exhaust Gas Recirculation
EI Ð Electronic Ignition
ETR Ð Electronically Tuned Receiver
EVAP Ð Evaporation EmissionExh Ð Exhaust

F Ð Degrees Fahrenheit
Fed Ð Federal (All States Except Calif.)
FF Ð Front Drive Front Engine
FL Ð Fusible Link
FLW Ð Fusible Link Wire
FP Ð Fuel Pump
FRT Ð Front
ft Ð Foot
FWD Ð Front Wheel Drive
4WD Ð Four Wheel Drive
4 x 4 Ð Four Wheel Drive
4 A/T Ð Four Speed Automatic Transmission/Transaxle
Gal Ð Gallon
GEN Ð Generator
GND Ð Ground
Gov Ð Governor
g Ð Gram
Harn Ð Harness
HC Ð Hydrocarbons
HD Ð Heavy Duty
Hg Ð Hydrargyrum (Mercury)
HiAlt Ð High Altitude
HO2S Ð Heated Oxygen Sensor
HVAC Ð Heater±Vent±Air±Conditioning
IAC Ð Idle Air Control
IAT Ð Intake Air Temperature
IC Ð Integrated Circuit / Ignition Control
ID Ð Identification / Inside Diameter
IGN Ð Ignition
INJ Ð Injection
IP Ð Instrument Panel
IPC Ð Instrument Panel Cluster
Int Ð Intake
ISC Ð Idle Speed Control
J/B Ð Junction Block
kg Ð Kilograms
km Ð Kilometers
km/h Ð Kilometer per Hour
kPa Ð Kilopascals
kV Ð Kilovolts (thousands of volts)
kW Ð Kilowatts
KS Ð Knock Sensor
L Ð Liter
lb ft Ð Foot Pounds
lb in Ð Inch Pounds
LF Ð Left Front
LH Ð Left Hand
LR ÐLeft Rear
LS Ð Left Side
LWB Ð Long Wheel Base
L±4 Ð In±Line Four Cylinder Engine
MAF Ð Mass Air Flow
MAN Ð Manual
MAP Ð Manifold Absolute Pressure
Max Ð Maximum
MC Ð Mixture Control
MFI Ð Multiport Fuel Injection
MIL Ð Malfunction Indicator Lamp
Min Ð Minimum
mm Ð Millimeter
MPG Ð Miles Per Gallon
MPH Ð Miles Per Hour
M/T Ð Manual Transmission/Transaxle
MV Ð Millivolt

0A±13
GENERAL INFORMATION
N Ð Newtons
NA Ð Natural Aspirated
NC Ð Normally Closed
N´M Ð Newton Meters
NO Ð Normally Open
NOX Ð Nitrogen, Oxides of
OBD Ð On-Board Diagnostic
OD Ð Outside Diameter
O/D Ð Over Drive
OHC Ð Overhead Camshaft
OL Ð Open Loop
O2 Ð Oxygen
O2S Ð Oxygen Sensor
PAIR Ð Pulsed Secondary Air Injection System
P/B Ð Power Brakes
PCM Ð Powertrain Control Module
PCV Ð Positive Crankcase Ventilation
PRESS Ð Pressure
PROM Ð Programmable Read Only Memory
PNP Ð Park/Neutral Position
P/S Ð Power Steering
PSI Ð Pounds per Square Inch
PSP Ð Power Steering Pressure
Pt. Ð Pint
Pri Ð Primary
PWM Ð Pulse Width Modulate
Qt. Ð Quart
REF Ð Reference
RF Ð Right Front
RFI Ð Radio Frequency Interference
RH Ð Right Hand
RPM Ð Revolutions Per Minute
RPM Sensor Ð Engine Speed Sensor
RPO Ð Regular Production Option
RR Ð Right Rear
RS Ð Right Side
RTV Ð Room Temperature Vulcanizing
RWAL Ð Rear Wheel Antilock Brake
RWD Ð Rear Wheel Drive
SAE Ð Society of Automotive Engineers
Sec Ð Secondary
SFI Ð Sequential Multiport Fuel Injection
SI Ð System International
SIR Ð Supplemental Inflatable Restraint System
SOHC Ð Single Overhead Camshaft
Sol Ð Solenoid
SPEC Ð Specification
Speedo Ð Speedometer
SRS Ð Supplemental Restraint System
ST Ð Start / Scan Tool
Sw Ð Switch
SWB Ð Short Wheel Base
SYN Ð Synchronize
Tach Ð Tachometer
TB Ð Throttle Body
TBI Ð Throttle Body Fuel Injection
TCC Ð Torque Converter Clutch
TCM Ð Transmission Control Module
TDC Ð Top Dead Center
Term Ð Terminal
TEMP Ð Temperature
TODÐ Torque On Demand
TP Ð Throttle Position
TRANS Ð Transmission/Transaxle
TURBO Ð TurbochargerTVRS Ð Television & Radio Suppression
TVV Ð Thermal Vacuum Valve
TWC Ð Three Way Catalytic Converter
3 A/T Ð Three Speed Automatic Transmission/Transaxle
2WD Ð Two Wheel Drive
4 x 2 Ð Two Wheel Drive
U±joint Ð Universal Joint
V Ð Volt(s)
VAC Ð Vacuum
VIN Ð Vehicle Identification Number
VRRRE Ð Vehicle Refrigerant Recovery and Recycling
Equipment
V±ref Ð ECM Reference Voltage
VSS Ð Vehicle Speed Sensor
VSV Ð Vacuum Switch Valve
V±6 Ð Six Cylinder ªVº Engine
V±8 Ð Eight Cylinder ºVº Engine
W Ð Watt(s)
w/ Ð With
w/b Ð Wheel Base
w/o Ð Without
WOT Ð Wide Open Throttle
Service Parts Identification Plate
The Vehicle Information Plate (Service Parts ID plate) is
provided on all vehicle models.
It is located on the center dash wall inside the engine
compartment. The plate lists the VIN (Vehicle
Identification Number), paint information and all
production options and special equipment on the vehicle
when it was shipped from the factory.
905R200002

0B±5 MAINTENANCE AND LUBRICATION
Explanation of Complete Vehicle
Maintenance Schedule
Brief explanations of the services listed in the preceding
Maintenance Schedule are presented below.
Replace all questionable parts and note any necessary
repairs as you perform these maintenance procedures.
Front and Rear Axle Lubricant
Replacement
Check the lubricant level after every 7,500 miles (12,000
km) of operation and add lubricant to level of filler hole if
necessary.
Replace the front and rear axle lubricant at 15,000 miles
(24,000 km) and 30,000 miles (48,000 km) and after
every 30,000 miles (48,000 km) of operation thereafter.
Air Cleaner Element Replacement
Replace the air cleaner under normal operating
conditions every 30,000 miles (48,000 km).
Operation of the vehicle in dusty areas will necessitate
more frequent replacement.
Spark Plug Replacement
Replace the plugs at 100,000 miles (160,000 km)
intervals with the type specified at the end of this section.
Cooling System Service
Drain, flush and refill system with new engine coolant.
Refer to
ªRecommended Fluids and Lubricantsº in this
section, or ENGINE COOLING (SEC.6B).
Timing Belt Replacement
Replacement of the timing belt is recommended at every
100,000 miles (160,000 km).
Failure to replace the timing belt may result in serious
damage to the engine.
Valve Clearance Adjustment
Incorrect valve clearance will result in increased engine
noise and reduced engine output.
Retorque the camshaft bracket bolts before checking and
adjusting the valve clearance.
Check and adjust the valve clearance whenever
increased engine noise is heard.
Tire Rotation
Rotate tires every 7,500 miles (12,000 km).
Front Wheel Bearings Lubricant
Replacement (Vehicles Produced Before
July/31/2001)
Clean and repack the front wheel bearings at 30,000
miles (48,000 km) intervals.
Refer to DRIVE SHAFT SYSTEM (SEC. 4C).
Front Wheel Bearings Check (Vehicles
Produced After Aug./1/2001)
Inspect hub unit bearing at every 60,000 miles (96,000
km).
If there is abnormal condition, replace hub unit bearing.
Radiator Core and Air Conditioning
Condenser Cleaning
Clean the front of the radiator core and air conditioning
condenser, at 60,000 miles (96,000 km) intervals.
Fluid Level Check
A fluid loss in any system (except windshield
washer) may indicate a problem. Repair the system
at once.
Engine oil level
Check level and add if necessary. The best time to check
the engine oil level is when the oil is warm. After stopping
the engine with the vehicle on a level surface, wait a few
minutes for the oil to drain back to the oil pan. Pull out the
oil level indicator (dipstick). Wipe it clean and push the oil
level indicator back down all the way. Pull out the oil level
indicator, keeping the tip down, and look at the oil level on
it.
Add oil, if needed, to keep the oil level above the ªADDº
mark and between the ªADDº and ªFULLº marks in the
operating range area. Avoid overfilling the engine since
this may cause engine damage. Push the oil level
indicator back down all the way after taking the reading.
If you check the oil level when the oil is cold, do not run the
engine first. The cold oil will not drain back to the pan fast
enough to give a true oil level.
Engine coolant level and condition
Check engine coolant level in the coolant reservoir and
add engine coolant if necessary. Inspect the engine
coolant and replace it if dirty or rusty.
Windshield washer fluid level
Check washer fluid level in the reservoir and add if
necessary.
Power steering system reservoir level
Check and keep at the proper level.
Brake master cylinder reservoir level
Check fluid. Keep fluid at proper level. A low fluid level can
indicate worn disc brake pads which may need to be
serviced.
Hydraulic clutch system
Check fluid level in the reservoir. Add fluid as required.
Battery fluid level
Check fluid level in the battery.
Fluid Leak Check
Check for fuel, water, oil or other fluid leaks by looking at
the surface beneath the vehicle after it has been parked
for a while. Water dripping from the air conditioning
system after use is normal. If you notice gasoline fumes or
fluid at any time, locate the source and correct it at once.
Engine Oil and Oil Filter Replacement
Always use API SE, SF, SG, SH or ILSAC GF±1 quality
oils of the proper viscosity.
When choosing an oil, consider the range of
temperatures the car will be operated in before the next oil
change. Then, select the recommended oil viscosity from
the chart.

0B±12MAINTENANCE AND LUBRICATION
Maintenance Service Data
Service Data and Specifications
ENGINEValve clearance (cold)Intake 0.28+0.05 mm (0.011+0.002 in)
Exhaust 0.3+0.05 mm (0.012+0.002 in)
Spark plug typeK16PR-P11/PK16PR11/RC10PYP4
Spark plug gap1.05 mm (0.04 in)
BRAKEBrake pedal free play6±10 mm (0.24±0.39 in)
Parking brake travel6±7 notches
WHEEL ALIGNMENTToe-in (Front)0 to +2 mm (0 to +0.08 in)
Toe-in (Rear)0+5 mm (0+0.2 in)
Camber (Front)0
+30'
Camber (Rear)0
+1

Caster (Front)2
30'+45'
Toe±Axis (Rear)+1

PROPELLER SHAFTFlange torque63 N´m (46 lb ft)
WHEEL AND TIRESSizeP235/65R17
Wheel nut torque118 N´m (87 lb ft)
Tire inflation pressure (Front)180 kPa (26 psi)
* Tire inflation pressure (Rear)180 kPa (26 psi)
* Unless otherwise specified on tire information label on the vehicle.
Approximate Capacities
ItemsMetric MeasureU.S. Measure
Fuel tank74 L19.5 Gal.
* CrankcaseOil Change with Filter4.7 L5.0 Qt
Oil Change without Filter4.0 L4.2 Qt
CoolantA/T11.1 L11.7 Qt
TransmissionAutomatic8.6 L9.1 Qt
Transfer1.35 L1.4 Qt
AxleRear1.77 L1.87 Qt
Front1.25 L1.33 Qt
Shift on the fly system0.12 L0.13 Qt
Power steering1.0 L1.1 Qt
Air conditioning (R-134a)0.6 L1.32 Qt
*Crankcase capacities shown are approximate refill capacities. After refill, recheck oil level.

3C±16FRONT SUSPENSION
Lower Control Arm
Lower Control Arm and Associated Parts
450R200003
Legend
(1) Nut, Front
(2) Bush, Front
(3) Bolt, Front
(4) Nut, Rear
(5) Bush, Rear
(6) Bolt, Rear
(7) Bolt, Lower Ball Joint(8) Bolt, Torsion Bar Arm
(9) Torsion Bar Arm Bracket and Nut
(10) Torsion Bar
(11) Lower Control Arm
(12) Lower Ball Joint and Nut
(13) Shock Absorber
(14) Stabilizer Link
Removal
1. Raise the vehicle and support the frame with suitable
safety stands.
2. Remove wheel and tire assembly. Refer to
Wheel in
this section.
3. Remove the tie-rod end from the knuckle. Refer to
Power Steering Unit in Steering section.
4. Remove the retaining ring from the front axle driving
shaft to release the shaft from hub(Except 2WD
model). Refer to
Front Hub and Disc in Driveline/Axle
section.
5. Support lower control arm with a jack.

FRONT SUSPENSION3C±21
Lower Ball Joint
Lower Ball Joint and Associated Parts
450RW011
Legend
(1) Bolt
(2) Lower Ball Joint(3) Nut
(4) Nut and Cotter Pin
Removal
1. Raise the vehicle and support the frame with suitable
safety stands.
2. Remove wheel and tire assembly. Refer to
Wheel in
this section.
3. Remove the tie-rod end from the knuckle. Refer to
Power Steering Unit in Steering section.
4. Remove the retaining ring from the front axle driving
shaft to release the shaft from hub(Except 2WD
model). Refer to
Front Hub and Disc in Driveline/Axle
section.
5. Support lower control arm with a jack.
6. Remove lower ball joint nut and cotter pin, then use
remover J±29107 to remove the lower ball joint from
the knuckle.
CAUTION: Be careful not to damage the ball joint
boot.
901RW163

4A1±1 DIFFERENTIAL (FRONT)
AXIOM
DRIVELINE/AXLE
CONTENTS
Differential (Front) 4A1. . . . . . . . . . . . . . . . . . . . . . .
Differential (Rear) 4A2. . . . . . . . . . . . . . . . . . . . . . .
Driveline Control System 4B1. . . . . . . . . . . . . . . . . Driveline Control System (TOD) 4B2. . . . . . . . . . .
Drive Shaft System 4C. . . . . . . . . . . . . . . . . . . . . .
Transfer Case (TOD) 4D2. . . . . . . . . . . . . . . . . . . .
Differential (Front)
CONTENTS
Service Precaution 4A1±1. . . . . . . . . . . . . . . . . . . . . .
Front Drive Axle 4A1±2. . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis 4A1±2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pinion Shaft Oil Seal 4A1±3. . . . . . . . . . . . . . . . . . . . .
Pinion Shaft Oil Seal and Associated Parts 4A1±3
Removal 4A1±3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 4A1±4. . . . . . . . . . . . . . . . . .
Installation 4A1±4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Drive Axle Assembly 4A1±5. . . . . . . . . . . . . . .
Front Drive Axle Assembly and
Associated Parts 4A1±5. . . . . . . . . . . . . . . . . . . . . .
Removal 4A1±6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 4A1±6. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential Assembly 4A1±8. . . . . . . . . . . . . . . . . . . .
Disassembled View 4A1±8. . . . . . . . . . . . . . . . . . . .
Disassembly 4A1±9. . . . . . . . . . . . . . . . . . . . . . . . . .
Reassembly 4A1±11. . . . . . . . . . . . . . . . . . . . . . . . . .
Differential Cage Assembly 4A1±20. . . . . . . . . . . . . . .
Disassembled View 4A1±20. . . . . . . . . . . . . . . . . . . .
Disassembly 4A1±20. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 4A1±21. . . . . . . . . . . . . . . . . .
Reassembly 4A1±21. . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications 4A1±23. . . . . . . . . . .
Special Tools 4A1±25. . . . . . . . . . . . . . . . . . . . . . . . . .
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM(SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE REFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFOMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED , do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally,such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specification. Following these
instructions can help you avoid damage to parts and
systems.

DIFFERENTIAL (FRONT) 4A1±2
Front Drive Axle
Diagnosis
ConditionPossible causeCorrection
Oil Leak At Front AxleWorn or defective oil seal.Replace the oil seal.
Front axle housing cracked.Repair or replace.
Oil Leak At Pinion ShaftToo much gear oil.Correct the oil level.
Oil seal worn or defective.Replace the oil seal.
Pinion flange loose or damaged.Tighten or replace.
Noises In Front Axle Drive Shaft
JointBroken or worn drive shaft joints and
bellows (BJ and DOJ).Replace the drive shaft joints and
bellows.
ªClankº When Accelerating From
ªCoastºLoose drive shaft joint to output shaft
bolts.Tighten.
Damaged inner drive shaft joint.Replace.
Shudder or Vibration During
Acceleration
Excessive drive shaft joint angle.Repair.
AccelerationWorn or damaged drive shaft joints.Replace.
Sticking spider assembly (inner drive
shaft joint).Lubricate or replace.
Sticking joint assembly (outer drive
shaft joint).Lubricate or replace.
Vibration At Highway SpeedsOut of balance or out of round tires.Balance or replace.
Front end out of alignment.Align.
Noises in Front AxleInsufficient gear oil.Replenish the gear oil.
Wrong or poor grade gear oil.Replace the gear oil.
Drive pinion to ring gear backlash
incorrect.Adjust the backlash.
Worn or chipped ring gear, pinion
gear or side gear.Replace the ring gear, pinion gear or
side gear.
Pinion shaft bearing worn.Replace the pinion shaft bearing.
Wheel bearing worn.Replace the wheel bearing.
Differential bearing loose or worn.Tighten or replace.
Wanders and PullsWheel bearing preload too tight.Adjust the wheel bearing preload.
Incorrect front alignment.Adjust the front alignment.
Steering unit loose or worn.Tighten or replace.
Tire worn or improperly inflated.Adjust the inflation or replace.
Front or rear suspension parts loose
or broken.Tighten or replace.
Front Wheel ShimmyWheel bearing worn or improperly
adjusted.Adjust or replace.
Incorrect front alignment.Adjust the front alignment.
Worn ball joint or bush.Replace the ball joint or bush.
Steering unit loose or worn.Tighten or replace.
Tire worn or improperly inflated.Replace or adjust the inflation.
Shock absorber worn.Replace the shock absorber.

4A1±3 DIFFERENTIAL (FRONT)
Pinion Shaft Oil Seal
Pinion Shaft Oil Seal and Associated Parts
415R200001
Legend
(1) Flange Nut
(2) Flange(3) Oil Seal
(4) Outer Bearing
(5) Collapsible Spacer
Removal
1. Raise the vehicle and support it at the frame.
The hoist must remain under the front axle housing.
2. Drain the front axle oil by loosening the drain plug(1).
412RS001