radiator ISUZU TF SERIES 2004 Owners Manual

HEATER AND AIR CONDITIONING 1-85

RESULT SYMPTOM TROUBLE CAUSE CORRECTION
Discharge
(High)
pressure
gauge
abnormally
high Reduced or no air flow through
the condenser


Condenser clogged or dirty


Radiator (condenser) fan
does not operate properly

Clean


Check cooling fan
operation
No bubbles in sight glass when
condenser is cooled by water
(Insufficient cooling)




Excessive refrigerant in
system





Check sight glass.
(See “Reading Sight
Glass”)


Discharge and
recover refrigerant.
Recharge to specified
amount
After stopping air conditioning,
pressure drops approx. 196 kPa
(2.0kg/cm
2 / 28 PSI) quickly

Air in system


Evacuate and charge
refrigerant system
Discharge
(High)
pressure
gauge
abnormally
low Insufficient cooling and excessive
bubbles in the sight glass







Insufficient refrigerant in
system







Check sight glass.
(See “Reading Sight
Glass”)

Check for leaks


Discharge and
recover refrigerant.
Recharge to specified
amount
Low pressure gauge indicates
vacuum

Clogged or defective
expansion valve

Replace the
expansion valve
Frost or dew on refrigerant line
before and after receiver/ drier or
expansion valve, and low pres-
sure gauge indicates vacuum
Restriction caused by debris
or moisture in receiver/drier


Check system for
restriction and
replace receiver/drier

After turning off air conditioning,
high and low pressure gauge
balanced quickly


Compressor seal defective


Poor compression due to
defective compressor
gasket

Replace or repair
compressor
Suction
(Low)
pressure
gauge
abnormally
high Low pressure gauge is lowered
after condenser is cooled by
water


Excessive refrigerant in
system



Discharge and
recover refrigerant
Recharge to specified
amount
Low pressure hose temperature
around the compressor refrigerant
line connector is lower than
around evaporator



Unsatisfactory valve
operation due to defective
temperature sensor of
expansion valve


Expansion valve opens too
long

Replace the
expansion valve




After turning off air conditioning,
high and low pressure gauge is
balanced quickly

Compressor gasket is
defective


Replace


Air conditioning turns off before
passenger compartment is
sufficiently
cool
Electronic thermostat
defective

Check the electronic
thermostat and
replace as necessary


* For the charging and discharging operations in the table above, refer to “RECOVERY, RECYCLING,
EVACUATION AND CHARGING” in this section.

1-86 HEATER AND AIR CONDITIONING

RESULT SYMPTOM TROUBLE CAUSE CORRECTION
Suction
(Low)
pres-sure
abnormally
low
Condenser is not hot and
excessive bubble in sight glass







Insufficient refrigerant








Check sight
glass.(See “Reading
Sight Glass”)


Check for leaks


Discharge and
recover refrigerant.
Recharge to specified
amount
Frost on the expansion valve inlet
line

Expansion valve clogged


Replace the
expansion valve

A distinct difference in
temperature between the inlet and
outlet refrigerant lines of the
receiver/drier

Receiver/drier clogged




Replace the receiver/
drier


Expansion valve outlet refrigerant
line is not cold and low-pressure
gauge indicates vacuum



The temperature sensor of
the expansion valve is
defective, and the valve
cannot regulate the correct
flow of the refrigerant

Replace the
expansion valve



Discharge temperature is low and
air flow from vents is restricted

Frozen evaporator core fins


Check electronic
thermostat and
replace as necessary
Low-pressure gauge reading is
low, or a vacuum reading may be
shown

Clogged or blocked
refrigerant line


Replace refrigerant
line
Suction
(Low) and
Discharge
(High)
pressure
abnor-
mally
high
No bubbles in sight glass after
condenser is cooled by water
(Insufficient cooling)





Excessive refrigerant in
system






Check sight
glass.(See “Reading
Sight Glass”)


Discharge and
recover refrigerant.
Recharge to specified
amount
Reduce air flow through con-
denser


Condenser clogged

Radiator (condenser) fan
does not rotate properly

Clean

Check cooling fan
operation
Suction (Low) pressure hose is
not cold

Air in system

Evacuate and charge
refrigerant
Suction
(Low) and
Discharge
(High)
pres-sure
abnor-
mally
low
Insufficient cooling and excessive
bubbles in the sight glass

Insufficient refrigerant in
system


Check sight glass.
(See “Reading Sight
Glass”)


Check for leaks

Discharge and
recover refrigerant.
Recharge to specified
amount

7A1-4 CONSTRUCTION AND FUNCTION
MAIN DATA AND SPECIFICATION
Model JR405E
Torque Converter Type Three Elements, One Stage & Two Phase Type
With Lock-up Function
Torque Converter Stall Torque Ratio 1.8
Name ATF DEXRON

Quantity 9.2L-9.6L AT F
Cooling System Water Cooled Type (Radiator)
1st 2.786
2nd 1.546
3rd 1.000
4th (Over Drive) 0.694
Gear Ratio
Reverse 2.273
Low Clutch L/C 7
High Clutch H/C 5
Reverse Clutch R/C 2Number of Disc Clutch
Low One-way Clutch L/O.C 1 Set
Low & Reverse
Brake L&R/B 6
Brake
2-4 Brake 2-4/B 5Number of Disc
Sun Gear 33
Pinion
Gear 21Front Planetary
Ring Gear 75
Sun Gear 42
Pinion
Gear 17
Planetary Gear Unit
Rear Planetary
Ring Gear 75Number of Teeth