brake ISUZU TF SERIES 2004 Workshop Manual

CLUTCH 7C-37
REASSEMBLY



Reassembly Steps


1. Cylinder body
2. Spring


3. Piston and piston cup


4. Push rod
5. Boot







Important Operations
1. Cylinder Body
1) Clean the cylinder body.
2) Apply brake fluid to the cylinder bore.


3. Piston and piston Cup
1) Apply brake fluid to the piston and piston cup.
2) Install the cups to the piston.
Note the installation direction of the piston cups in the
illustration.
3) Install the piston and piston cup to the cylinder body.

ELECTRICAL-BODY AND CHASSIS 8A-3
PAGE
Power Window ........................................................................................................... 8A- 310
Audio, Clock and Cigarette Lighter .......................................................................... 8A- 329
Power Door Mirror ...................................................................................................... 8A- 337
Rear Defogger ............................................................................................................ 8A- 349
SRS-Air Bag ................................................................................................................ 8A- 358
Transfer Case Control Module .................................................................................. 8A- 361
Anti-Lock Brake System ............................................................................................ 8A- 373
Immobilizer ................................................................................................................. 8A- 376
Keyless Entry ............................................................................................................. 8A- 385
Anti Theft ....................................................................................................................8A- 400
Auto Cruise ................................................................................................................. 8A- 412
Trailer Hitch ................................................................................................................ 8A- 415
Connector List ................................................................................................................8A- 418

8A-12 ELECTRICAL-BODY AND CHASSIS
ABBREVIATIONS
Abbreviation Meaning of abbreviation Abbreviation Meaning of abbreviation
A Ampere (S) LH Left hand
ABS Anti-lock brake system LWB Long wheel base
ASM Assembly MPI Multipart fuel injection
AC Alternating current M/T Manual transmission
A/C Air conditioner QOS Quick On Start system
ACC Accessories RH Right hand
CARB Carburetor RR Rear
C/B Circuit breaker RWAL Rear wheel anti-lock brake system
CSD Cold start device SRS Supplemental restraint system
DIS Direct ignition system ST Start
EBCM Electronic brake control module STD Standard
ECGI Electronic control gasoline injection SW Switch
ECM Engine control module SWB Short wheel base
ECU Electronic control unit TCM Transmission control module
EFE Early fuel evaporation V Volt
42 Two-wheel drive VSV Vacuum switching valve
44 Four-wheel drive W Watt (S)
FL Fusible link WOT Wide open throttle
FRT Front W/ With
H/L Headlight W/O Without
IC Integrated circuit
IG Ignition
kW Kilowatt

8A-20 ELECTRICAL-BODY AND CHASSIS

Caution:
Never push or tow the vehicle in an attempt to start it.
Extensive damage to the emission system and other
vehicle parts will result.
(Only catalytic converter vehicle)
Treat both the discharged battery and the booster battery
with great care when using jumper cables.
Carefully follow the procedure outlined below.
Always be aware of the dangers of sparking.
Failure to follow the following procedure can result in:
a. Serious personal injury, specially to your eyes.
b. Extensive property damage from a battery explosion,
battery acid discharge, or electrical file.
c. Extensive damage to the electronic components o
f
both vehicles.
Do not use a 24 volt booster battery.
Serious damage to the vehicle's electrical system and
electronic components will result.

Jump Starting Procedure
1. Set the parking brake on both vehicles.
2. If one or both vehicles is equipped with a manual
transmission, place the gear shift in the "NEUTRAL"
position.
3. Turn off the ignition on both vehicles.
4. Turn off all vehicle lights and accessories.
5 Be sure that the two vehicles are not touching.

Attach the end of one jumper cable to the booster battery
positive terminal.
6
Attach the other end of the same cable to the discharged
battery positive terminal.
7. Once again, check that the booster battery has a 12 vol
t
rating.
8.
Attach one end of the remaining booster cable to the
booster battery negative terminal.
9.
Attach the other end of the booster cable to a solid ground
(such as the air conditioner compressor mounting bracke
t
or the alternator mounting bracket) in the engine room o
f
the vehicle with the discharged battery.
Be sure that the ground connection is at least 500 mm (20
in) from the discharged battery.

ELECTRICAL-BODY AND CHASSIS 8A-25
Light Name Rated Power
V-W Number of
Bulbs Lens
Color Remarks
W/O Tacho 5Illumination light 14-2
W/ Tacho 7White
Turn Signal 14-1.12 2 Green
High Beam 14-1.12 1 Blue
Low Fuel 14-1.12 1 Amber
A/T Oil Temp 14-1.12 1 Red
Brake system 14-1.12 1 Red
4WD 14-1.12 1 Green
Seat belt 14-1.12 1 Red
Oil pressure 14-1.12 1 Red
ABS 14-1.12 1 Amber
SEDIMENTER 14-1.12 1 Red
AIR BAG 14-1.12 1 Red
Brake 14-1.12 1 Red
Charge 14-1.12 1 Red
Check Trans 14-1.12 1 Red
Check 4WD 14-1.12 1 Red
Power drive 14-1.12 1 Amber
3rd start 14-1.12 1 Green
4L 14-1.12 1 Green
Cruise Set 14-1.12 1 Green
Check Engine 14-1.12 1 Amber
Front Fog 14-1.12 1 Green
Rear foglight 14-1. 12 1 Amber
Glow 14-1.12 1 Amber
P LED 1 Green
R LED 1 Green
N LED 1 Green
D LED 1 Green
3 LED 1 Green
2 LED 1 Green












Indicator/
Warning
light
A/T shift
indicator
L LED 1 Green

8A-166 ELECTRICAL-BODY AND CHASSIS
TROUBLESHOOTING
STOPLIGHT AND HIGH MOUNTED STOPLIGHT
1. One side of stoplight does not light

Checkpoint Trouble Cause Countermeasure


Replace the bulb or repair
connector contact

Burned out bulb or poor
connector contact
NG

Repair open circuit or
connector contact


Repair open circuit or
connector contact


Open circuit or poor connector
contact


Continuity between
9
H-9 - 2 F-6 (LH) (or
2
F-5 (RH))


Open circuit or poor connector
contact

Continuity between

C-109 - 4 F-6 (LH) (or
4
F-5 (RH)) NG NG OK
OK

Stoplight bulb continuity




2. Both sides of stoplight do not light



Adjust the switch installation
position

Stop light switch (or brake
switch) function

Incorrect the switch installation
or adjustment
NG

Repair open circuit or
connector contact
Voltage between 2 F-6
ground or 2
F-5 - ground
with brake pedal depressed
(Should be battery voltage
present)
Open circuit or poor connector
contact between stoplight
switch (or brake switch) and
stoplight NG OK

Reinstall or replace fuse No.
SBF-9 (50A)
or 1
C-108 - 4
C-107
Fuse No. C-18 (15A)


Fuse No. SBF-9 (50A, Fuse
and Relay box)
or 1
C-108 - 4
C-107
Fuse No. C-18 (15A)


Poor fuse contact or blown
NG
OK

ELECTRICAL-BODY AND CHASSIS 8A-167

3. High mounted stoplight does not light

Checkpoint Trouble Cause Countermeasure



Repair or replace the high
mounted stoplight

Continuity between 3
L-5 -
1
L-5


High mounted stoplight
malfunction
NG
Repair an open circuit or
connector contact between
3
L-5 - 8 H-6
Voltage between 1 L-5 -
ground with brake pedal
depressed
(Should be battery voltage
present)
Open circuit or poor connector
contact
NG OK

Repair grounding point contact

C-2


Grounding point
C-2


Poor grounding point contact
NG
OK

8A-260 ELECTRICAL-BODY AND CHASSIS
WARNING AND INCIDATOR LIGHT
1. When the parking brake lever is pulled, the indicator light does not light up

Checkpoint Trouble Cause Countermeasure


Replace or reinstall the bulb

Bulb burned out or loose
contact
NG

Adjust or replace the parking
brake SW.

Parking brake SW. installation
position and function

Incorrect SW. adjustment or
poor SW. point contact


Repair open circuit or
connector contact
Continuity between the
parking brake SW. connector
1
C-39 (Lever: 1 R-4) and
9
B-23

Open circuit or poor connector
contact
NG NG OK
OK

Brake indicator light bulb
continuity


Replace the parking brake
SW.
Continuity between the
parking brake SW. connector
1
C-39 (Lever: 1 R-4) and
the ground when the parking
brake is operated

Parking brake SW.
malfunction
NG OK

ELECTRICAL-BODY AND CHASSIS 8A-261
2. Even when the parking brake lever is pulled, the indicator light does not go off

Checkpoint Trouble Cause Countermeasure

Adjust the SW. installation
position or replace the parking
brake SW. Incorrect the parking brake
SW. adjustment or brake SW.
faulty
NG Thermo unit malfunction
Replace the brake fluid level
SW., or vacuum SW., or
repair a short circuit between
the parking brake SW.
connector 1
C-39
(Lever: 1
R-4) and 9 B-23
or the brake fluid level SW.
connector 2
C-37 and 9
B-23, (or the vacuum SW.
connector 1
C-38 and 9
B-23 : 4JH1-TC ONLY)
Check to see if the indicator
light goes off when the parking
brake SW. connector 1
C-39
(Lever: 1
R-4) is
di t d
Brake fluid level SW. or
vacuum SW. faulty or short
circuit
NG OK

Parking brake SW. installation
position and function




3. Oil pressure warning light does not go off while engine is running


Refer to ENGINE Section

Refer to ENGINE Section
NG Thermo unit malfunction

Repair a short circuit between
1
E-1 and 3 B-24

Check to see the warning light
goes off when the oil pressure
SW. connector
1
E-1 is disconnected


Short circuit


Replace the oil pressure unit
(or the oil pressure SW.)
Continuity between the oil
pressure SW. connector
1
E-1 and the body ground
when the engine is operating


Oil pressure unit (or oil
pressure SW) faulty
NG NG OK
OK

Engine oil pressure

8A-274 ELECTRICAL-BODY AND CHASSIS





Terminal Connector No. B-23
No. C24SE
1
ABS CONT. (BRAKE)
2


3


4


5


6


7


8


9
BRAKE
10
CHARGE
11
TURN (RIGHT)
12


13


14


15


16


17
ILLUMI (-)
18
ILLUMI (+)

Terminal Connector No. B-24
No. C24SE
1


2
4LO
3
OIL PRESSURE
4


5
4WD
6
CHECK 4WD
7


8


9
SPEED (+)
10
4P OUTPUT
11


12
STARTER
13
TEMP
14
FUEL
15
FRONT FOG
16


17
CHECK ENGINE
18
AIR BAG
19
SEAT BELT
20
BEAM (+)
21
TURN (LEFT)
22
BEAM (-)
23
BEAM (+)
24


25


26
POWER GND
27
SPEED (-)
28
GND UNIT
29
+B
30
IGN