Transmission ISUZU TF SERIES 2004 Workshop Manual

ON-VEHICLE SERVICE (AW30–40LE) 7A3-1
TRANSMISSION
ON-VEHICLE SERVICE (AW30–40LE)
CONTENTS

Service Precaution .................................................
7A3-2
Location of Clutch, Brake, One-Way Clutch
and Solenoid ........................................................
7A3-3
Operation of Clutch, Brake and One-Way
Clutch ....................................................................
7A3-4
Trnasmission Indentification ..............................
7A3-4
Speed Change and Lock-Up Pattern ...............
7A3-5
Overdrive and Lock-Up Operating
Conditions ............................................................
7A3-5
Diagnosis .................................................................
7A3-6
Basic Troubleshooting ........................................
7A3-6
Manual Shifting Test ...........................................
7A3-12
Stall Test ..............................................................
7A3-12
Time Lag Test .....................................................
7A3-13
Hydraulic Test ......................................................
7A3-14
Road Test .............................................................
7A3-15
Shift Pont Chart and Lock-Up Point Chart ..........
7A3-19
Shift Pont Chart ...................................................
7A3-19
Lock-Up Point Chart ...........................................
7A3-20
Transmission Fluid Level and Condition .............
7A3-21
Inspection .............................................................
7A3-21
ATF Replacement ..................................................
7A3-22
Inspection .............................................................
7A3-22
Neutral Start Switch (Mode Switch) .....................
7A3-23
Inspection .............................................................
7A3-23
Removal ...............................................................
7A3-23
Installation ............................................................
7A3-23
Brake Signal ............................................................
7A3-24
Inspection .............................................................
7A3-24
Input and Output Revolution Sensor ....................
7A3-25
Inspection .............................................................
7A3-25
Pattern Select Switch .............................................
7A3-25
Inspection .............................................................
7A3-25
Solenoid ...................................................................
7A3-26
Inspection .............................................................
7A3-26

ATF Temperature Sensor ......................................
7A3-27
Inspection .............................................................
7A3-27
Select Lever ....................................................... 7A3-28 Remove or Disconnect .......................................
7A3-28
Install or Connect .................................................
7A3-29
Shift Cable ......................................................... 7A3-31
Remove or Disconnect .......................................
7A3-31
Install or Connect .................................................
7A3-32
Torque specifications ..........................................
7A3-33
Transmission Control Module (TCM) ...................
7A3-34
Removal ................................................................
7A3-34
Installation .............................................................
7A3-34
Shift Solenoid and Lock-Up Solenoid ...................
7A3-35
Removal ................................................................
7A3-35
Installation .............................................................
7A3-36
Valve Body Assembly and Pressure Control Solenoid .................................................
7A3-37
Removal ................................................................
7A3-37
Installation .............................................................
7A3-39
Rear Oil Seal (Adapter Housing, 4

4) .................
7A3-40
Removal ................................................................
7A3-40
Installation .............................................................
7A3-40
Rear Oil Seal (Extension Housing, 4
2) ..............
7A3-41
Removal ................................................................
7A3-41
Installation .............................................................
7A3-41
Transmission Assembly .........................................
7A3-42
Transmission and Associated Parts .................
7A3-42
Removal ................................................................
7A3-43
Installation .............................................................
7A3-46
Major Components ..............................................
7A3-50

7A3-4 ON-VEHICLE SERVICE (AW30 –40LE)

Operation of Clutch, Brake and One-Way Clutch




Transmission Identification


RUW37ASH004301
Legend
(1)
Transmission Model Number
(2)
Production Serial Number


The identification plate is located on the right rear side
of the transmission.

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-5

Speed Change and Lock-Up Pattern
If you select a speed as shown below by specifying
respective positions of transmission shift lever, transfe
r
switch and pattern select switch, the transmission
control computer controls speed change and lock-up
operations based on the specified pattern in accordance
with the degree of throttle opening and vehicle speed.
Pattern select sw. position Transmission shift position


D 3 2 L
NORMAL, POWER 1st 
[2nd] 
[3rd] 
[O/D] 1st 
[2nd] 
[3rd] 1st 
2nd
(3rd) 1st
(2nd)
3rd START 3rd fixing — —

[ ]: The lock-up operation is available.
( ): Transmission is shifted at high speed to prevent overrun.


Overdrive and Lock-Up Operating Conditions
The overdrive and lock-up clutch operate if the following
conditions are satisfied.
Overdrive Lock-up clutch
Shift pattern position
NORMAL NORMAL
Transmission shift position
D range 
Brake lamp switch
— OFF
Throttle opening
Fully closed Except fully closed
Accelerator About 52 km/h (32 mph) or more 2nd: About 76 km/h (47 mph) or
more
Vehicle speed Deceleration About 42 km/h (26 mph) or more 3rd: About 56 km/h (35 mph) or more
O/D: About 67 km/h (42 mph) or
more

7A3-6 ON-VEHICLE SERVICE (AW30 –40LE)

Diagnosis
Basic Troubleshooting
AW30
–40LE transmission, with Transmission Control
Module (TCM), differs from the Mechanical – Hydraulic
control type transmissions. Accordingly, its
troubleshooting procedure differs also.
Before troubleshooting an TCM, first determine whethe
r
the problem is electrical or mechanical. To do this, just
refer to the basic troubleshooting flowchart provided
below.

If the cause is already known, using the basic
troubleshooting chart below along with the
troubleshooting chart should speed the procedure.




F07R200005-X

7A3-12 ON-VEHICLE SERVICE (AW30 –40LE)

Manual Shifting Test
NOTE: With this test, it can be determined whether the
trouble lies within the electrical circuit or is a mechanical
problem in the transmission.
1. Disconnect TCM connector
Inspect manual driving operation
2. Inspect manual driving operation
Check that the shift and gear positions correspond
with the table.
If the “L", “2", “3" and “D" range gear positions are
difficult to distinguish, do perform the following road
test.
While driving, shift through the “L", “2", “3" and “D"
ranges. Check that the gear change corresponds to
the gear position.
If any abnormality is found in the above test, do
perform the stall, time lag or gear change tests.



RUW37ASH004101
3. Connect TCM connector
With the engine off, connect the TCM connector.


Stall Test



RUW37ALH000101
The object of this test is to check the overall
performance of the transmission and engine b
y
measuring the maximum engine speeds at the “D" and
“ R" ranges.
NOTE:
1. Perform the test at normal operation fluid
temperature (50 – 80 
C or 122 – 176 
F).
2. Do not continuously run this test longer than 5 seconds.

7A3-14 ON-VEHICLE SERVICE (AW30 –40LE)

Measure Time Lag
1. Fully apply the parking brake.
2. Start the engine. Check idling speed (A/C OFF).
3. Shift the shift lever from “N" to “D" range. Using a
stopwatch, measure the time it takes from shifting
the lever until the shock is felt.
Time lag: Less than 0.7 seconds
4. In same manner, measure the time lag for “N"


“R".
Time lag: Less than 1.2 seconds
Evaluation
1. If “N" 
“ D" time lag is longer than specified:

Line pressure too low
 Forward clutch malfunction
 No.2 one-way clutch not operating properly
2. If “N" 
“ R" time lag is longer than specified:

Line pressure too low
 Direct clutch malfunction
 No.3 brake malfunction
3. If both time lag is longer than specified:

Line pressure too low

Hydraulic Test



RUW37ALH000201
Preparation

1. Warm up the transmission fluid.
2. Remove the transmission case test plug and mount the hydraulic pressure gauge.
Oil pressure gauge: J –29770 –A
NOTE: Perform the test at normal operation fluid
temperature (50 – 80 
C or 122 – 176 
F).

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-21

Transmission Fluid Level and Condition
Inspection
Park vehicle on level ground and set parking brake.
With the engine idling, move the shift lever through all
positions from “P" to “L", then return to position “P".
Check to see if the level of fluid comes to “HOT" range
of about 80 
 

C (176 
 

F) on the dipstick gauge.
If the level of fluid is too low, replenish to bring it to
maximum level in “HOT" range.
Inspection of fluid condition. If the ATF is black o
r
smells burnt, replace it.



RUW37ASH002501

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-23

Neutral Start Switch (Mode Switch)
Inspection
With a circuit tester, make a continuity test on the
neutral start switch with the moving piece set in each
position.










RTW37BSH000101
Removal
Preparation:
Disconnect negative ( –) battery cable.
1. Remove the rear side ATF cooler pipe from the
transmission elbow.
2. Disconnect neutral start switch connector.
3. Unstake the lock washer, and then remove the shaft
nut.
4. Remove the neutral start switch.
Installation
To install, follow the removal steps in the reverse order,
noting the following points;
If a engine starts at any selector position except “N ” o
r
“ P ”, the neutral start switch (mode switch) should be
adjusted.
1. Loosen the neutral start switch bolt and set the shift
selector to the “N" range.
2. Align the groove and neutral basic line.
3. Hold in position and tighten the bolt and nut.
Torque:
Nut – 7 N 


m (61 Ib in)
Bolt – 13 N 


m (113 Ib in)
4. Lock the nut with the lock washer tubs at two points.



RUW17ASH013601

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-27

ATF Temperature Sensor
Inspection

1. Disconnect the front side ATF cooler pipe from the
elbow and remove the elbow.
2. Remove the ATF temperature sensor from the transmission case.
3. Place the ATF temperature sensor in a container o
f
ATF.



RUW37ASH004001
4. Measure the resistance between each terminals,
while warming ATF.
Resistance: 0.5 – 30 k






(at 0

 

C – 120 
 

C)
5. If either of the measured values exceeds the
specified value, replace the ATF temperature
sensor.
Torque: 15 N 


m (11 Ib ft)

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-31

Shift Cable





RTW47ALF000101
Legend

(5) Bracket
(1) Select lever
(6) Clip
(2) Shift cable retaining pawl
(7) Shift cable
(3) Manual shaft select lever
(8) Select lever base
(4) Adjuster


Remove or Disconnect
1.
Block the wheels.
2.
Disconnect the negative battery cable.
3.
Move the select lever to the “N ” position.
4.
Remove the rear console and front console.
5.
Disconnect the shift cable from the select lever.
6.
Press on the shift cable retaining pawl to remove the
cable from the select lever base.
7.
Disconnect the shift cable from the transmission
side.
8.
Remove the shift cable from the bracket.
9.
Pull the shift cable free from the bottom of the
vehicle.