switch ISUZU TF SERIES 2004 Workshop Manual

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-11

Comparison of mode
1. The normal drive mode is set at the normal shift
points.
2. The shift points of the power drive mode are shifted
to the higher speed side, compared to the normal
drive mode.
3. The 3rd start mode is a special mode used
exclusively for starting in third gear.
3rd start Mode
1. The 3rd start switch will operate when switched on
after all of the following conditions are present:
a. The gear select position is “D" range only.
b. Vehicle speed is 11 km/h (7 mph) or less.
c. Transmission oil temperature is 120

C (248

F)
or less.
d. Accelerator opening is at 8% or less.
2. Cancel Release
1. Cancellation by driver
a. Turning off the 3rd start mode switch
b. Shifting select position to “3", “2", or “L" (3rd
start mode is not canceled by selecting “N",
“ R", or “P")
c. Ignition key is turned off.
2. Automatic cancellation
a. When vehicle runs at 34 km/h (21mph) o
r
more for 1 second or more
b. When transmission oil temperature reaches 120

C (284

F) or above
NOTE: The mode returns to normal drive mode o
r
power drive mode after the 3rd start mode is canceled.
Backup Mode
If a major system failure occurs which could affect
safety or damage the transmission under normal
vehicle operation, the diagnostic system detects the
fault and overrides the Transmission Control Module
(TCM).
The “CHECK TRANS" light flashes to alert the driver,
and the transmission must be manually shifted as
follows:


Select lever position Gear Ratio Selected
D 4 (Fourth)
Manual 3 4 (Fourth)
Manual 2 3 (Third)
Manual L 3 (Third)
R Reverse
Shifts are firmer to prevent clutch slip and consequent
wear. The fault should be corrected as soon as
possible.

7A2-12 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

Functions of Input / Output Components
Component Function
Transfer low signal Detects the transfer High/Low position.
OD Cancel signal Detects whether the cruise control unit is judged OD cancel mode.
Output revolution sensor
(Transmission) Detects the vehicle speed.
Input revolution sensor
(Transmission) Detects the input revolution (OD direct clutch drum revolution).
Engine revolution sensor Detects the engine revolution with CAN.
Throttle position signal Detects the throttle opening rate with CAN.
Neutral start switch Detects the select lever position.
Pattern select switch Detects whether the driver has selected "NORMAL" or "POWER" mode.
Brake lamp switch Detects whether the driver has pressed the brake pedal or not.
Oil temperature sensor Detects the oil temperature.




I
n
p
u t
Diagnostic start switch Starts self-diagnosis and displays a code for faulty part if any.
I
n
p
u t
/
O
u t
p
u t Data link connector When connected with Tech2 or tester, can communicate the data for function
check, etc.
Shift solenoid S1, S2 Selects shift point and gear position suited to the vehicle running condition on the
basis of TCM output.
Lock-up control solenoid SL Control the lock-up clutch suited to the vehicle running condition on the basis of TCM output.
Pressure control solenoid
STH Adjusts throttle pressure by energizing current of linear pressure control solenoid
to prevent the shift shock and to obtain shift smoothly.
"CHECK TRANS" lamp When trouble has occurred to throttle position sensor, vehicle speed sensor, or
solenoid, "CHECK TRANS" lamp is blinked to warn the driver. If also displays the
trouble code.
A/T OIL TEMP warning
lamp Lights when ATF oil temperature rises. (Turned on at greater than 146


C
(295

F). Turned off at less than 132

C (270

F).
POWER lamp Lights when POWER MODE detected.



O
u
t
p
u
t
3rd Start lamp Lights when 3rd Start MODE detected.
C
o
m
p
u t
e r Transmission Control
Module (TCM) Based on the signal from each switch and sensors, judges necessary shift point
and lock-up operation, and send signal to each solenoid.

7A2-22 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

TRANSMISSION DATA
ITEM UNIT ENGIN RUNNING AT IDLE
Current Gear 1 st/2 nd/3 rd/4 th 1 st
Target Gear 1 st/2 nd/3 rd/4 th 1 st
Vehicle Speed km/h 0 km/h
AT Output Speed (Automatic Transmission) RPM 0 RPM
AT Input Speed (Automatic Transmission) RPM 675725 RPM
Engine Speed RPM 675725 RPM
Throttle Position Sensor Signal % 0.007.00%
AT Oil Temperature (Automatic Transmission) C Depends on conditions
TCM Status Transfer Low /Transfer High Transfer HI
Desired PC Solenoid Pressure (STH) kPa 34.397.0 kPa
Desired PC Solenoid Current (STH) mA 8351020 mA
PC Solenoid Actual Current (STH) mA 8351020 mA
Gear Ratio : 1 Depends on uper hood
TCC Slip Speed RPM 0 RPM
Shift Position Actual P/R/N/L/2/3 P
Inhibitor Switch P/R/N/L/2/3 P
Transmission Check Light On/Off Off
AT Oil Temperature Lamp (Automatic
Transmission) On/Off Off
3 rd Start Lamp On/Off Off
Power Lamp On/Off Off
Shift Solenoid S1 On/Off On
Shift Solenoid S2 On/Off On
Shift Solenoid S3 On/Off Off
Diag Switch Condition On/Off Off
Power Switch On/Off Off
Brake Switch On/Off Off
Cruise Switch On/Off Off
4L Signal On/Off Off
3 rd Start Switch On/Off Off
Coolant Temperature C Depends on conditions
Torque Request (timing Retard) CA 0 CA
Garage Shift Mode On/Off Off
CAN TPS % 0.00%
CAN Signal Valid Counter (ECM)
— 0  255
CAN Signal Valid Counter (TCM) — 0  255

7A2-28 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

2.Demand of Data
1.
Connect Tech-2 to the vehicle. When activated by
turning on the power of Tech-2, push the "Enter"
switch.
2.
Turn on the ignition switch (without starting the
engine)
3.
In the main menu of Diagnostic Tester, push "F1:
Service Programming System (SPS)".
4.
Push "F0: Request Info" of Tech-2.

5.
Where vehicle data has been already saved in
Tech-2, the existing data come on display. In this
instance, as Tech-2 starts asking whether to keep
the data or to continue obtaining anew data from
the control unit, choose either of them.





6.
If you select “continue ”, you have to select “Model
Year ”, “Vehicle Type ”, “Controller Type (Engine) ”.
7.
After that. then push button and turn Ignition
switch tuned on, off, on following Tech-2 display.
Tech-2 will read information from controller afte
r
this procedure.
8.
During obtaining information, Tech-2 is receiving
information from the control unit chosen. In
replacing the control unit, please be sure to
undertake "Obtaining Information" from the new
unit. With VIN not being programmed into the new
control unit at the time of shipment, "obtaining
information" is not complete (because the vehicle
model, engine model and model year are specified
from VIN). For the procedure get additional
information on vehicles, instruction will be
provided in dialog form, when TIS2000 is in
operation.
9.
Following instructions by Tech-2, push the "Exit"
switch of Tech-2, turn off the ignition of the vehicle
and turn off the power of Tech-2, thereby
removing from the vehicle.

3.Data Exchange
1.
Connect Tech-2 to P/C, turn on the power and
click the "Next" button of P/C.
2.
Check VIN of the vehicle and choose "Next".
3.
When a lack of data is asked from among the
following menu, enter accordingly.
Select following Menu

Model Year

Model

Engine type

Transmission type

Destination code (vehicles for general
export)*1

Immobiliser
* 1: How to read the destination code
"Destination code can be read from ID Plate affixed on
vehicles, while on VIN plate the destination code is
described at the right-hand edge of Body Type line. In
Fig.-3, the destination code can be read as "EK4"
(Europe).

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-29





4.
After choosing the data, click the "Next" button.
5.
When all the necessary information is entered, the
"details" of software within the database that
match the entered data will appear fo
r
confirmation. Click the "Program" switch and then
download the new software onto Tech-2.
6. "Data Transfer" comes on display. The progress o
f
downloading will be displayed on the screen in the
form of bar graph.
7.
Upon finishing the data transfer, turn off the powe
r
of Tech-2, removing from P/C.


4. Programming of ECM 1.
Check to see if batteries are fully charged, while
ABS connectors shall be removed from the
vehicle.
2.
Connect Tech-2 to Vehicle Diagnostic Connectors.
3.
Turn on the power of Tech-2 and the title screen
comes on display.
4.
Turn on the ignition (without allowing the engine to
start)
5.
On the title screen of Tech-2, push the "Enter"
button.
6.
Choose "F: Service Programming System" on the
main screen and then choose "Fl: Programming".
7.
While data is being transferred, "Downloading"
will be displayed on the Tech-2 screen.
8.
Upon finishing the data transfer, Tech-2 will
display "Reprogramming Successful". Push the
"Exit" button to bring program to completion.

9.
Following "Procedure 2: Demand of Data", try ove
r
again "Information Obtaining" and check to
confirm if the data has been correctly re-loaded.
10. Upon finishing confirmation, turn off the ignition o
f
the vehicle and then turn off the power of Tech-2,
removing from the vehicle.

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-31

16 – Terminal Data Link Connector (DLC)
OBD standardizes Data Link Connector (DLC)
configurations. The DLC, formerly referred to as the
ALDL, will be a 16 –terminal connector found on the
lower right side of the driver's side instrument panel. All
manufacturers must conform to this 16 –terminal
standard.






060R300015






810RT022




PIN 1 – uart
PIN 2 – J1850 Bus + L line on 2–wire systems, or single wire (ECM)
PIN 3 – (Not used)
PIN 4 – Chassis ground pin
PIN 5 – Chassis ground pin
PIN 6 – ECM diagnostic enable
PIN 7 – KW2000
PIN 8 – (Not used)
PIN 9 – Primary UART
PIN 10 – (Not used)
PIN 11 – TCM diagnostic enable
PIN 12 – ABS diagnostic or CCM diagnostic enable
PIN 13 – SIR diagnostic enable
PIN 14 – (Not used)
PIN 15 – (Not used)
PIN 16 – Battery power from vehicle unswitched (4 AMP MAX.)

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-39

DTC P0705 (FLASHING CODE 17) Transmission Range Sensor Circuit
Malfunction


RTW37ALF000501

Circuit Description
The neutral start switch gives the signals related to the
selector lever position (PRND32L) to the Transmission
Control Module (TCM). The neutral start switch turns on
when the select lever is shifted to the P, R, N, D, 3, 2 o
r
L range. The neutral start switch, which is connected to
the starter switch circuit, is available only when the
select lever is in the P or N range (Engine run).
The neutral start switch is connected to the
transmission manual shaft and installed in the
transmission case.

Condition for setting the DTC

The TCM detects following "Condition 1" for 30 sec
continuously.
 The TCM detects following "Condition 2" for 10 sec
continuously.
Condition 1("Open"):
When the TCM detects no signal of range senso
r
more than 2.0 sec at following conditions.

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-41

DTC P0705 (FLASHING CODE 17) Transmission Range Sensor Circuit
Malfunction


Step Action Value(s) YES NO
1
Was the powertrain On-Board Diagnostics (OBD)
System check performed ? — Go to Step 2 Go to OBD
System Check
2

1. Install the scan tool.

2. Key “ON"

3. Review and record scan tool data.
4. Operate the vehicle with in scan tool data.
Does the scan tool indicate DTC P0705 ? — Go to Step 3 Refer to
Diagnostic Aids
3 Measure the voltage shifting the select lever every
position, between TCM connector terminals and
ground which performed selecting to every position.

1. Key “OFF"
2. Disconnect the TCM connector.

3. Key “ON"

4. Connect the DMM to the TCM connector terminal
and ground.
Is the displayed voltage at every position normal ? 7—16V Go to Step 7 Go to Step 4
4 Measure the voltage between terminal the neutral
start switch and ground.

1. Key“OFF"
2. Disconnect the neutral start switch connector.

3. Key“ON"

4. Connect the J39200 DMM to the each terminal of
the neutral start switch connector E79-3 and
ground.
If the problem found repair as necessary.
Was the problem found? 7—16V Verify repair Go to Step 5
5 Measure the resistance shifting the select lever to
every position, between terminal neutral start switch
connector E79-3 and E79other terminal.

1. Key“OFF"

2. Disconnect the neutral start switch connector.
3. Key“ON"

4. Connect the DMM to the each terminal of the
neutral start switch connector E79-3 and E79-5 or
E79-2 or E79-6 E79-8 or E79-7 or E79-9 or E79-
10.
If the problem found repair as necessary.
Was the problem found? Less than
1


Verify repair Go to Step 6

7A2-42 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

Step Action Value(s) YES NO
6 Check the wire between terminal C-95 and E-79 for
open.

1. Connect the J39200 DMM to the each terminal of
the TCM connector and neutral start switch.
If the problem found repair as necessary.
Was the problem found? Verify repair —
7 Replace the TCM.
IMPORTANT; The replacement TCM must be
programmed. (Refer to SPS for procedure.)
Is the action complete? — Verify repair —

7A2-68 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)


 Engine REV is 7000 rpm.

Coolant tempreature is 80

C.

No detect DTC P0712, 0713.
 No detect DTC P0560.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring. Inspect
for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.

Inspect the wiring for EMI (Erectro-Magnetic
Interference). Check that all wires are properly
routed away from coil, and generator. Also check fo
r
improperly installed electrical options. When this test
is performed, turn “OFF" on electronic autoparts
switches to improperly for a noise preventing.