switch ISUZU TF SERIES 2004 Workshop Manual

DIAGNOSIS (JR405E) 7A2-97
No. B2: Poor Acceleration at Starting

Description:

Starting acceleration is poor.

Diagnosis Hints:

In addition to the low engine output, faulty gear shifting of AT or fixing at the 3rd position may be possible.
Therefore, in case of such a trouble that "maximum speed is low, and acceleration is poor", it should be cleared
up whether the trouble is originated from the engine system of AT system by a running test, inspection of stall
revolution, etc.

Possible Cause:

Clogged air cleaner, out of injection timing, dropped compression pressure, etc.

Fixing at 3rd position (fail-safe activated).
Since the gear is fixed at the 3rd position because of the fail-safe function, a trouble that "Maximum
speed is low, and acceleration is poor" is resulted. In this case, the DTC is memorized.
When TCM stops operation because of faulty TCM ground, the gear is fixed at the 3rd position because
of a mechanical reason. In this case, no DTC is memorized.

Disordered inhibitor switch.

Incorrect properties of throttle opening signal (serial communication) of throttle position sensor.
Throttle opening signal (serial communication) of the throttle position sensor does not change in
proportion to the throttle opening. In this case, fixing at the high or low gear results in such a trouble
that "Maximum Speed is Low and Acceleration is Poor".

Slip of clutch (low clutch, high clutch).

If slip of clutch is caused, a DTC (gear ratio error) is stored.

Dropped line pressure.

Trouble in the torque converter system (faulty operation).

Step Action Yes No
1 Test Drive.
Is the gear smoothly shifted in the order of 1st to 2nd, 2nd to 3rd,
3rd to 4th gear and lock up?

Clogged air cleaner,
out of injection
timing, dropped
compression
pressure, etc.

Go to Step 2
2 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 3 Go to Step 3
3 Are any DTCs stored?
Go to DTC Chart Go to Step 4

7A2-98 DIAGNOSIS (JR405E)
Step Action Yes No
4 Are the quantity, contamination and smell normal?
If the ATF level is
low, replenish up to
the specified level.

Go to Step 5

If ATF is extremely
black and
contaminated and
smells burnt, slip of
the clutch is
supposed.
Overhaul the AT
unit.
5 Inspection of inhibitor switch using a Tech 2 or circuit tester.
When the select lever is operated, is the data display in the Tech 2
correct or voltage at each range correct?

Inhibitor SW

TCM
A2 (P)
A17 (3)
B2 (2)
B10 (N)
B11 (D)
B19 (R)
B21 (L)
C95
(2 )
(10)
(11 )
(19)
(21) Y E L /V IO
RED/BLK
BLUBLK/GRN
Starter Relay
C94
(2 )
(3 )
BH22
(1)
(6)
(4)
(7)
(5)
(2) P
2
R
N
D
3
L
Start SW
PNK/BLU
E51
(2)
(4)
(8)
(5)
(1)
(9)
(6)
(3)
(10)
(7)
(38)
(15)
(3)
(37)
H4PNK/BLK
RED/YEL Y E L /V IO
BLK/GRN
PNK/BLK RED/BLK
BLU RED/YEL
PNK/BLU
BLK/WHT
BLK
BLK BLK/WHT Key Switch WHT
WHT
ICU (W/ Immobilis e r)
Ground (W/O Immobilis e r)
TCM terminal
RangeA2 B19 B10 B11 B17 B2 B21
P10 –
14.5V-- - - - -
R-10 –
14.5V-- ---
N--10 –
14.5V----
D - - - 10 –
14.5V---
3----10 –
14.5V--
2-----10 –
14.5V-
L------10 –
14.5V
Go to Step 6
Adjust the inhibitor
switch.

DIAGNOSIS (JR405E) 7A2-101
Step Action Yes No
1 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 2 Go to Step 2
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is
low, replenish up to
the specified level.

Go to Step 4

If ATF is extremely
black and
contaminated and
smells burnt, slip of
the clutch is
supposed.
Overhaul the AT
unit.
4 Are the engine speed and other engine system correct?
Go to Step 5
Repair the defect or
replace.
5 Inspection of electrical or mechanical fault
Is the signal from each pressure switch changed synchronously?
Control Valve

TCM
B1
B12
B20 RED/YEL
WHT/BLK 2-4 Brake Pressure SW
Terminal
Assembly
YEL
E54
(7)
(12)
(1)H23
(12)
(10)C95
(1)
(12)
(20) RED/YEL
YEL
WHT/BLK
L&R Brake Pressure SW
High Clutch Pressure SWH22
(8)
Range TCM terminal
GearB20
(High clutch
pressure SW)B1
(2-4 brake pressure
SW)B12 (Low & reverse
brake pressu re SW)
P - More than 10V More than 10V More than 10VR Reverse More than 10V More than 10V -N - More than 10V More than 10V More than 10VD, 3, 2 1st More than 10V More than 10V More than 10V2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VL 1st More than 10V More than 10V -2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VGo to Step 6
Repair the defect or
replace.

DIAGNOSIS (JR405E) 7A2-103
No. B4: Large Shock When Shift Lever is Changed to N to D
Range or N to R Range

Description:

Large shock is felt when selecting D or R range from N range during the idling after warming up.

Diagnosis Hints:

Check the entire condition of the vehicle for unusual other than AT including faulty engine mount, exhaust
hanger, etc.

When the fail-safe operation, select shock may grow worse. In such a case, check for the DTC. If no DTC is
issued, shock due to faulty operation of the control valve or burnt clutch is considered.

Possible Cause:

High engine idling.

Dislocated select lever, improper inhibitor switch adjusting point.

Faulty or insufficient tightening of engine mount, exhaust mount.

Play of suspension.

Burnt clutch.

Too low or high line pressure.

Faulty input signal system.

Faulty control valve. (faulty operation or sticking of accumulator)

7A2-106 DIAGNOSIS (JR405E)
No. B6: Engine Starter Does Not Run in P or N Range
No. B7: Engine Starter Runs Except in P or N Range

Description:

The engine starter does not run though the P or N range is selected.

The engine starter runs though the R or D, 3, 2or L range is selected.

Possible Cause:

Disordered select cable.

Disordered Inhibitor switch, disconnection or short-circuit of inhibitor switch.


No. B8: Extended Time Lag When Shift Lever is Changed to N to D

Description:

The shift time lag is longer than standard value when shift lever is changed to N to D.

Possible Cause:

Forward range line pressure is low.

Slip of low & reverse clutch.

Slip of low one-way clutch.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).

Faulty low clutch duty solenoid operation.

Shortage or faulty quality of ATF.


No. B9: Extended Time Lag When Shift Lever is Changed to N to R

Description:

The shift time lag is longer than standard value when shift lever is changed to N to R.

Possible Cause:

Reverse range line pressure is low.

Slip of low & reverse brake.

Slip of reverse clutch.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).

Faulty low & reverse brake duty solenoid operation.

Shortage or faulty quality of ATF.

DIAGNOSIS (JR405E) 7A2-109
Step Action Yes No
1 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 2 Go to Step 2
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is
low, replenish up to
the specified level.

Go to Step 4
If ATF is extremely
black and
contaminated and
smells burnt, slip of
the clutch is
supposed.
Overhaul the AT
unit.
4 Are the engine speed and other engine system correct?
Go to Step 5
Repair the defect or
replace.
5 Inspection of electrical or mechanical fault
Is the signal from each pressure switch changed synchronously?
Control Valve

TCM
B1
B12
B20 RED/YEL
WHT/BLK 2-4 Brake Pressure SW
Terminal
Assembly
YEL
E54
(7)
(12)
(1)H23
(12)
(10)C95
(1)
(12)
(20) RED/YEL
YEL
WHT/BLK
L&R Brake Pressure SW
High Clutch Pressure SWH22
(8)
Range TCM terminal
GearB20
(High clutch
pressure SW)B1
(2-4 brake pressure
SW)B12 (Low & reverse
brake pressu re SW)
P - More than 10V More than 10V More than 10VR Reverse More than 10V More than 10V -N - More than 10V More than 10V More than 10VD, 3, 2 1st More than 10V More than 10V More than 10V2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VL 1st More than 10V More than 10V -2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10V
Go to Step 6
Repair the defect or
replace.

7A2-112 DIAGNOSIS (JR405E)
Step Action Yes No
1
Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 2 Go to Step 2
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is
low, replenish up to
the specified level.

Go to Step 4
If ATF is extremely
black and
contaminated and
smells burnt, slip of
the clutch is
supposed.
Overhaul the AT
unit.
4 Are the engine speed and other engine system correct?
Go to Step 5
Repair the defect or
replace.
5 Inspection of electrical or mechanical fault
Is the signal from each pressure switch changed synchronously?
Control Valve

TCM
B1
B12
B20 RED/YEL
WHT/BLK 2-4 Brake Pressure SW
Te r m i n a l
Assembly
YEL
E54
(7)
(12)
(1)H23
(12)
(10)C95
(1)
(12)
(20) RED/YEL
YEL
WHT/BLK
L&R Brake Pressure SW
High Clutch Pressure SWH22
(8)
Range TCM terminal
GearB20
(High clutch
pressure SW)B1
(2-4 brake pressure
SW)B12 (Low & reverse
brake pressure SW)
P - More than 10V More than 10V More than 10VR Reverse More than 10V More than 10V -N - More than 10V More than 10V More than 10VD, 3, 2 1st More than 10V More than 10V More than 10V2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VL 1st More than 10V More than 10V -2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VGo to Step 6
Repair the defect or
replace.

DIAGNOSIS (JR405E) 7A2-115
No. D1: Faulty Gear Shifting (Different from Shift Pattern)

Description:

Gear is shifted, different from the specified shift pattern.

Diagnosis Hints:

When inspecting faulty gear shifting, it is important to distinguish between the fault of electric system and
mechanical system (AT main unit).

Fault of electric system.
Monitor the output signal (each solenoid driving signal) using with Tech 2. If a trouble signal is sent to the solenoid synchronously with the faulty gear shifting, the fault is originated in the electric system.
Monitor the input signal (signal from each sensor) using with Tech 2 and find an input signal by which the output signal (each solenoid driving signal) is subjected to fault.
Fault of the electric system may be derived from temperature or vibration. For instance, though the engine is normal while it is cold, fault may occur when the engine is warmed up or vehicle is running.

Fault of mechanical system.
If the gear is incorrectly shifted irrespective of operating signal (ON-OFF) of each solenoid, the faulty is originated from the machine system (AT).
If the clutch slips, ATF smells burnt, contaminated to be black or the stall speed increases.

Possible Cause:

Disordered select cable.

Disordered inhibitor switch.

Slip of clutch.
If slip of clutch is caused, a DTC (gear ratio error) is stored.

Fixing at 3rd position (fail-safe activated)
Since the gear is fixed at the 3rd position because of the fail-safe function, a trouble that "Faulty gear shifting" is resulted. In this case, the DTC is memorized.
When TCM stops operation because of faulty TCM ground, the gear is fixed at the 3rd position because
of a mechanical reason. In this case, no DTC is memorized.







Incorrect properties of throttle opening signal (serial communication) of throttle position sensor.
The throttle opening signal which is sent by serial communication from ECM and TCM is an important
signal for gear shifting. In case of ECM fault or when the throttle position sensor does not issue voltage
signal according to the throttle opening, the gear is not shifted by stepping over the accelerator.
If the output voltage of the throttle position sensor changes freely even though the throttle opening is
constant, the gear is shifted incorrectly.




Faulty speed sensor.

DIAGNOSIS (JR405E) 7A2-117
Step Action Yes No
5 Inspection of electrical or mechanical fault
Is signal to each solenoid and pressure switch changed
synchronously to the faulty gear shift?

Control Valve


TCM


B1





B12





B20 RED/YEL
WHT/BLK 2-4 Brake Pressure SW

Terminal
Assembly
YEL
E54

(7)





(12)





(1) H23

(12)





(10)C95

(1)





(12)





(20) RED/YEL
YEL
WHT/BLK
L&R Brake Pressure SW

High Clutch Pressure SW

H22

(8)
Control Valve

TCM
B6
B7
B8
B9
B22 (GND) BLU/BLK
WHT/BLU L&R Brake Solen oid

Te r m i n a l
Assembly
BLK/YEL
RED
2-4 Brake Solenoid

High Clutch Solenoid

Low Clu tch S olen oid

E54
(5)
(9)
(10)
(3)
(11)H23
(11)
(5)
(7)
(2)
(1)
GRY/REDC95
(6)
(7)
(8)
(9)
(22) BLU/BLK
BLK/YEL
RED
WHT/BLU
GRY/RED
Range TCM terminal
GearB20
(High clutch
pressure SW)B1
(2-4 brake pressure
SW)B12 (Low & reverse
brake pressure SW)P - More than 10V More than 10V More than 10VR Reverse More than 10V More than 10V -N - More than 10V More than 10V More than 10VD, 3, 2 1st More than 10V More than 10V More than 10V2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VL 1st More than 10V More than 10V -2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10V
Range TCM terminal
GearB8
(High clutch
solenoid)B9
(Low clutch
solenoid)B7
(2 -4 b rake
solenoid)B6
(Lo w & reve rs e
brake solenoid)P - Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)Approx. 6.2V
(AC ra ng e)
R Reverse Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)-
N - Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)Approx. 6.8V
(AC ra ng e)
D, 3, 2 1st Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)Approx. 6.8V
(AC ra ng e)
2nd Approx. 6.8V
(AC range)- - Approx. 6.8V
(AC ra ng e)
3rd - - Approx. 6.8V
(AC range)Approx. 6.8V
(AC ra ng e)
4th - Approx. 6.8V
(AC range)- Approx. 6.8V
(AC ra ng e)
L 1st Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)-
2nd Approx. 6.8V
(AC range)- - Approx. 6.8V
(AC ra ng e)
3rd - - Approx. 6.8V
(AC range)Approx. 6.8V
(AC ra ng e)
4th - Approx. 6.8V
(AC range)- Approx. 6.8V
(AC ra ng e)
Go to Step 6
In case of fault in
the machine
system, repair that
portion or replace
the unit.
Slip of clutch or fault
of control valve.

7A2-118 DIAGNOSIS (JR405E)
Step Action Yes No
6 Inspection of inhibitor switch using a Tech 2 or circuit tester.
Inspect the output voltage and throttle opening signal of the
throttle position sensor using a Tech 2 or circuit tester.

Inhibitor SW

TCM
A2 (P)
A17 (3)
B2 (2)
B10 (N)
B11 (D)
B19 (R)
B21 (L)
C95
(2 )
(10)
(11 )
(19)
(21) Y E L /V IO
RED/BLK
BLUBLK/GRN
Starter Relay
C94
(2 )
(3 )
BH22
(1)
(6)
(4)
(7)
(5)
(2) P
2
R
N
D
3
L
Start SW
PNK/BLU
E51
(2)
(4)
(8)
(5)
(1)
(9)
(6)
(3)
(10)
(7)
(38)
(15)
(3)
(37)
H4PNK/BLK
RED/YEL Y E L /V IO
BLK/GRN
PNK/BLK RED/BLK
BLU RED/YEL
PNK/BLU
BLK/WHT
BLK
BLK BLK/WHT Key Switch WHT
WHT
ICU (W/ Immobilis e r)
Ground (W/O Immobilis e r)
TCM terminal
RangeA2 B19 B10 B11 B17 B2 B21
P10 –
14.5V-- - - - -
R-10 –
14.5V-- ---
N--10 –
14.5V----
D - - - 10 –
14.5V---
3----10 –
14.5V--
2-----10 –
14.5V-
L------10 –
14.5V
Go to Step 7
Adjust the inhibitor
switch.
7 Is a voltage value in proportion to the throttle opening output?




TPSTCM
A16
C56
(28)C94
(16) RED/ WHT
C56
(49)
(38)
(57)
(69)ECM
A47 (GND)
A35 (Out put )
A26
A55 (+5V)
A69 (I dl e SW)
Go to Step 8
Repair the defect or
replace.