rims ISUZU TF SERIES 2004 Workshop Manual

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-227
Condition For Setting The DTC and Action Taken When The DTC Sets
Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up)
P0201 A Injector 1 Control
Circuit
P0202 A Injector 2 Control
Circuit
P0203 A Injector 3 Control
Circuit
P0204 A Injector 4 Control
Circuit
P0205 A Injector 5 Control
Circuit
31
P0206 A Injector 6 Control
Circuit 1. No DTC relating to CMP sensor and CKP sensor.
2. Under sequential injection.
3. Injection pulse is between 2.5ms and 7.5 ms.
4. Except fuel cut operation.
5. Engine speed is between 600rpm and 2000rpm.
6. 30 injection signals are not detected consecutively. No fail-safe function.

CIRCUIT DESCRIPTION
The Engine Control Module ECM has six individual
injector driver circuits. Each controls an injector. When
a driver circuit is grounded by the (ECM), the injector is
activated. The ECM monitors the current in each drive
r
circuit. The voltage on each driver is monitored to detect
a fault. If the voltage is not what the ECM expects to
monitor on the circuit, a DTC is set. This DTC is also
set if an injector driver is shorted to voltage or if there is
an open circuit.

DIAGNOSTIC AIDS
An injector driver circuit that is open or shorted to
voltage will cause a DTC P0201, P0202, P0203, P0204,
P0205 or P0206 to set. It will also cause a misfire due
to an inoperative injector.
Long term and short term fuel trims that are excessively
high or low are a good indication that an injector is
faulty.

6E–168 ENGINE DRIVEABILITY AND EMISSIONS
Trouble Code is set. This Diagnostic Trouble Code is
also set if an injector driver is shorted to voltage.
Diagnostic Aids
An injector driver circuit that is open or shorted to
voltage will cause a Diagnostic Trouble Code P0201 to
set. It will also cause a misfire due to an inoperativeinjector. A misfire Diagnostic Trouble Code will also be
set indicating which cylinder is inoperative.
Long term and short term fuel trims that are ex cessively
high or low are a good indication that an injector is
faulty.
Use Fuel Injector Coil Test Procedure to check for faulty
injectors.
Diagnostic Trouble Code (DTC) P0201 Injector 1 Control Circuit
Diagnostic Trouble Code (DTC) P0202 Injector 2 Control Circuit
Diagnostic Trouble Code (DTC) P0203 Injector 3 Control Circuit
Diagnostic Trouble Code (DTC) P0204 Injector 4 Control Circuit
Step A ction Value(s) Yes No
1 Was the “On-Board Diagnostic (OBD) System Check”
performed?
—Go to Step 2Go to On Board
Diagnostic
(OBD) System
Check
2 1. Connect the Tech 2.
2. Review and record the failure information.
3. Select “F0: Read DTC Infor By Priority” in “F0:
Diagnostic Trouble Code”.
Is the DTC P0201, P0202, P0203 or P0204 stored as
“Present Failure”?—Go to Step 3Refer to
Diagnostic Aids
and Go to Step
3
3 1. Using the Tech2, ignition “On” and engine “Off”.
2. Select “Clear DTC Information” with the Tech2 and
clear the DTC information.
3. Operate the vehicle and monitor the “F5: Failed
This Ignition” in “F2: DTC Information”.
Was the DTC P0201, P0202, P0203 or P0204 stored
in this ignition cycle?—Go to Step 4Refer to
Diagnostic Aids
and Go to Step
4
4 Check for poor/faulty connection at the injector or
ECM connector. If a poor/faulty connection is found,
repair as necessary.
Was the problem found?
—Verify repair Go to Step 5
5 Visually check the injector for the affected cylinder.
Was the problem found? —Go to Step 11Go to Step 6
22
89 11
E-60(J1)
E-6/E-7/E-8/E-9