roof ISUZU TF SERIES 2004 Workshop Manual

9-18 ACCESSORIES

ANTENNA
REMOVAL AND INSTALLATION


Removal
1. Remove the antenna screw 1.
2. Disconnect the feeder cable
3 connector
.
3. Remove the antenna cable
2 .
4. Pull out antenna downward.
Remove and install the antenna as illustrated.
Antenna unit is located on the roof panel driver side.
To install, follow the removal steps in the reverse order.


Installation
To install, follow the removal steps in the reverse order.

10-12 CAB
DISASSEMBLY



This illustration is based on RHD model
RTW4A0LF000701

Disassembly Steps

1. Switch bezel/Window regulator handle

2. Power window switch

3. Bezel

4. Door mirror cover

5. Door trim panel

6. Tweeter (Required Option)

7. Door mirror assembly

8. Outer waste seal

9. Bracket

10. Speaker assembly

11. Waterproof sheet

12. Inside lever

13. Window glass




14. Window regulator/Power window
regulator

15. Glass run

16. Glass run rear channel / Glass ran rear
channel with Door lock control or Anti
theft (EC)

17. Door lock assembly/Door lock assembly
with super lock

18. Outside handle protector (EUROPE)

19. Outside handle

20. Door lock cylinder protector (EUROPE)

21. Door lock cylinder / Door lock cylinder
with door lock switch (EC)
22. Door harness assembly
23. Anti rattler

10-14 CAB



 Remove the 2 screws and pull out the trim panel at the 8
clip positions (Window regulator handle type).
RTW3A0SH000701

6. Tweeter (Required option)

Disconnect the tweeter harness connector and remove
the 3 screws.



7. Door Mirror Assembly

Remove 3 fixing bolts and then remove the connector.
8. Outer Waste Seal



9. Bracket
10. Speaker Assembly

Remove the fixing screw and then remove the
connector.
11. Waterproof Sheet

Take care not to damage the sheet when peeling it off.
12. Inside Lever

Disconnect the door lock cables.

10-16 CAB
REASSEMBLY



This illustration is based on RHD model
RTW4A0LF000801

Reassembly Steps
1. Anti rattler
2. Door harness assembly

3. Door lock cylinder / Door lock cylinder
with door lock switch (EC)

4. Door lock cylinder protector (EUROPE)

5. Outside handle

6. Outside handle protector (EUROPE)
7. Door lock assembly / Door lock
assembly with super lock
8. Glass run rear channel / Glass ran rear channel with Door lock control or Anti
theft (EC)
9. Glass run
10. Window regulator / Power window
regulator



11. Window glass
12. Inside lever
13. Waterproof sheet
14. Speaker assembly
15. Bracket
16. Outer waste seal
17. Door mirror assembly
18. Tweeter (Required option)
19. Door trim panel
20. Door mirror cover
21. Bezel
22. Power window switch

23. Switch bezel / Window regulator handle

10-22 CAB
DISASSEMBLY


RTW3A0LF000601

Disassembly Steps

1. Switch bezel/Window regulator handle

2. Power window switch

3. Bezel

4. Door trim panel

5. Bracket

6. Speaker assembly

7. Waterproof sheet

8. Inside lever

9. Outer waste seal




10. Window regulator/Power window
regulator

11. Glass run rear channel

12. Door lock assembly

13. Glass run

14. Window glass

15. Outside handle
16. Door harness assembly
17. Anti rattler

10-24 CAB

5. Bracket
6. Speaker assembly


Remove the fixing bolt and then remove the connector.
7. Waterproof Sheet


Take care not to damage the sheet when peeling it off.
8. Inside Lever


Disconnect the door lock cables.
9. Outer Waste Seal


10. Window Regulator/Power Window Regulator


Remove the 2 bolts fixing the window glass through the
access hole.

Move the window glass upward and hold it with adhesive
tape.


Remove the 5 bolts fixing the window regulator.


Disconnect the power window motor connector.
11. Glass Run Rear Channel

Remove the bolt.
12. Door Lock Assembly


Disconnect the lock cable from the anti rattler.


Remove the 3 fixing screws and the bolt.


Disconnect the linkage and harness connector.
13. Glass Run


Remove the adhesive tape and move the window glass
downward.


Pull it out from the door frame of the channel.
14. Window Glass

Pull out the window glass upward.
15. Outside Handle


Remove the 2 fixing bolts.

CAB 10-25
REASSEMBLY

RTW3A0LF000701

Reassembly Steps
1. Anti rattler
2. Door harness assembly

3. Outside handle
4. Window glass
5. Glass run
6. Door lock assembly
7. Glass run rear channel
8. Window regulator/Power window regulator


9. Outer waste seal
10. Inside lever
11. Waterproof sheet
12. Speaker assembly
13. Bracket
14. Door trim panel
15. Bezel
16. Power window switch

17. Switch bezel/Window regulator handle

CAB 10-43


8. Headlining

Pull out the headlining with the retainer from roof rea
r
header panel as direction of shown in the illustration.
Note :
Remove steps (2-7) can be removed from the headlining in
any order.

8A-6 ELECTRICAL-BODY AND CHASSIS


Connecting the Connectors
Firmly grasp both sides (male and female) of the connector.
Be sure that the connector pins and pin holes match.
Be sure that both sides of the connector are aligned with each
other.
Firmly but carefully push the two sides of the connector
together until a distinct click is heard.


Connector Inspection
Use a circuit tester to check the connector for continuity.
Insert the test probes from the connector wire side.



CAUTION
Never insert the circuit tester test probes into the
connector open side to test the continuity.
Broken or open connector terminals will result.



Waterproof Connector Inspection
It is not possible to insert the test probes into the connector
wire side of a waterproof connector.
Use one side of a connector
1 with its wires cut to make the
test.
Connect the test connector to the connector
2 to be tested.
Connect the test probes to the cut wires to check the connecto
r
continuity.



Connector Pin Removal
Connector Housing Tang Lock Type
1. Insert a slender shaft 3into the connector housing open
end
4.
2. Push the tang lock
5up (in the direction of the arrow in the
illustration).
Pull the wire
6 with pin 7free from the wire side of the
connector.

ELECTRICAL-BODY AND CHASSIS 8A-433


No. Connector face No. Connector face
H-1
White
Battery (+) ~ Engine room H-10
WhiteINST ~ Front Door-RH
H-2
NOT USED H-11
NOT USED
H-3
(6VE1,
4JH1-TC)
White Battery (+) ~ Engine room H-12
BlackINST ~ Roof
H-4
(C24SE)
White Engine room ~ Mission H-13
WhiteINST ~ Door -LH
H-4
(6VE1,
4JA1-TC,
4JH1-TC)
White
Engine ~ Engine room H-14
WhiteRear body ~ Rear door-LH
H-5
NOT USED H-15
White
Engine room ~ Chassis
H-6
White
Engine room ~ INST H-16
WhiteRear body ~ Rear door-RH
H-7
White
Engine room ~ INST H-17
WhiteChassis ~ License plate lamp
H-8
NOT USED H-18
White
Engine room ~ INST
H-9
Blue
Engine room ~ Chassis H-19
~
H-21 NOT USED