Door trim clips ISUZU TROOPER 1998 Service Repair Manual

EXTERIOR/INTERIOR TRIM8J±3
Dash Side Trim Panel
Removal
1. Disconnect the battery ground cable.
2. Remove the Front door sill plate(2).
3. Remove the Dash side trim panel(3).

Turn up the door inner seal(1) of the body panel to
remove the clips of the trim panel.

Take care not to damage the harness and the
controller on the back of the trim panel.
643RW005
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. Lap the door inner seal over the trim panel to install
them securely to the body panel.
Assist Grip
Parts Location
745RW006
Legend
(1) Assist Grip
Removal and Installation

Refer to the Consoles removal and installation steps
in this section.

8J±8EXTERIOR/INTERIOR TRIM
632RW001
8. Remove the door trim panel(9).

Remove two fixing screws(8) in order to take off
seven clips(10) from the door panel.
635RS007

Disconnect the courtesy light connector(13) to lift
the door trim panel(14) and unlock the engagement
of the waist seal(12) section. Then, pass the inside
handle(11) through the mounting hole of the trim
panel, and detach the trim panel.
632RS015
9. Remove the inside handle.

EXTERIOR/INTERIOR TRIM8J±9
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. When installing the inside handle(2), assemble it
temporarily to the inside handle link(1).
632RS014
2. Pass the inside handle(4) through the mounting hole
of the trim panel and assemble the trim panel.
Engage seven clips(8) into the door panel. Also,
connect the courtesy light connector(5) and leave the
connectors of the speaker(7), tweeter(9) and power
window(3) drawn out to their prescribed positions, so
that they will not be caught.
Then, put the inside handle(4) to the normal position
of the inside handle link(6).
632RW006
3. Fit the claw(10) of the inside handle(11) securely into
the hole of the door panel and fix the inside handle
with the screw.
632RW007

EXTERIOR/INTERIOR TRIM8J±11
3. Remove the power window switch(3).

Pry the power window switch out and disconnect
the switch connector.
825RS084
4. Remove the inside handle fixing screw.

Remove the screw that fixes the inside handle(5),
slide the inside handle to the position illustrated,
and leave it there for the moment.
CAUTION: Take care not to impose excessive force
on the inside handle link(4), lest this link be
elongated, which could make it impossible to
operate the door with the inside handle.
632RW002
5. Remove the door trim panel(6).

Remove two fixing screws(8) to take off seven
clips(7) from the door panel.
655RW007

Lift the trim panel and unlock the engagement of the
waist seal section. Then, pass the inside lever
through the mounting hole of the trim panel, and
detach the trim panel.
6. Remove the inside handle.
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. When installing the inside handle(1), assemble
temporarily to the inside handle link(2).
652RS006

8J±12EXTERIOR/INTERIOR TRIM
2. Pass the inside handle through the mounting hole of
the trim panel. Assemble the trim panel. Engage
securely seven clips into the door panel. Also, leave
the connector of the power window drawn out to its
prescribed position, so that it will not caught.
3. Put back the inside handle(3) to the original position
of the link(5). Fit the claw(4) of the inside handle
securely into the hole of the door panel. Fix the
handle with the screw.
632RW011

8J±26EXTERIOR/INTERIOR TRIM
7. Remove the fuel filler lid opener(1).

Remove two opener fixing screws and disconnect
the cable(2).
686RW007
8. Remove the center console assembly.
9. Remove the fuel filler lid opener cable.

Roll up the floor carpet and remove the clips of the
chassis harness and body panel to pull out the
cable toward the fuel filler lid.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Insert the opener cable(2) into the body panel(1)
securely.
686RS002
2. Install the cable and clips to its original position to the
chassis harness and the body panel.
3. Check that the opener operates smoothly.
Fuel Filler Door
Parts Location
686RS003
Legend
(1) Fuel Filler Door
Removal
1. Remove the fuel filler door.
Installation
1. Install the fuel filler door.

8J±28EXTERIOR/INTERIOR TRIM
Wheel Opening Extension and Rocker Protector Assembly
Wheel Opening Extension, Rocker Protector Assembly and Associated Parts
620RW005
Legend
(1) Front Wheel Opening Extension Assembly
(2) Front Rocker Protector Assembly
(3) Rear Rocker Protector Assembly (Only LWB)
(4) Rear Door Wheel Opening Extension
Assembly (Only LWB)(5) Rear Quarter Wheel Opening Extension
Assembly (Only LWB)
(6) Rear Wheel Opening Extension Assembly
(Only SWB)
Removal
1. Remove the front wheel opening extension(2).

Let a 5mm drill(3) go through four blind rivets(5) to
disengaged riveted portions.
Remove two screws and disengage five clips (6),
then remove the front wheel opening extension
assembly.

EXTERIOR/INTERIOR TRIM8J±29
620RS005
2. Remove the rear quarter wheel opening extension
assembly (Only LWB).

Let a 5mm drill go through six blind rivets to
disengage riveted portions.
Disengage four clips, remove two screws, and
remove the rear quarter wheel opening extension
assembly.
3. Remove the rear wheel opening extension assembly
(Only SWB).

Let a 5mm drill go through four blind rivets to
disengage riveted portions. Remove two screws,
disengage eight clips, and remove the rear wheel
opening extension assembly.

Remove two fixing nuts (upper) and four fixing bolts
(lower).
4. Remove the rear door wheel opening extension
assembly (Only LWB).

Let a 5mm drill go through a blind rivet to disengage
riveted portions.
Disengage three clips, peel off the bonded portions
with two double surface adhesive tape and the rear
door wheel opening extension assembly.
5. Remove the rear rocker protector assembly (Only
LWB).

Loosen and pull three clips, remove a rear screw,
and remove the rear rocker protector assembly.
6. Remove the front rocker protector assembly.

Loosen and pull four clips, and remove the front
rocker protector assembly.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Use a new 2±sided adhesive tape whenever installing
each wheel opening extension assembly and rocker
protector assembly. Using a white gasoline, clean the
places in advance where a 2±sided adhesive tape is
affixed. Also, install the clips, screws and blind rivets
in the order specified as shown in the figure.