oil temperature JAGUAR S TYPE 1999 1.G Powertrain Manual

Glossary
2The following abbreviations are used in this document:
A Ab
bb
br
re
ev
vi
ia
at
ti
io
on
nD
De
es
sc
cr
ri
ip
pt
ti
io
on
n
AAC air assisted (injection) control valve
AAI air assisted injection
ABDC after bottom dead centre
A/C air conditioning
AH amp-hour
API American Petroleum Institute
APP accelerator pedal position (sensor)
ATDC after top dead centre
bank 1 A bank
bank 2 B bank
BBDC before bottom dead centre
BTDC before top dead centre
ûC degree Celsius
CHT cylinder head temperature (sensor)
CKP crankshaft position (sensor)
CMP camshaft position (sensor)
ECT engine coolant temperature (sensor)
EFT engine fuel temperature (sensor)
EGR exhaust gas recirculation
EMS engine management system
EOP engine oil pressure (sensor)
EOT engine oil temperature (sensor)
EVAP evaporative emission
ûF degrees Fahrenheit
HO2 heated oxygen (sensor)
Hz Hertz (cycles per second)
IAT intake air temperature (sensor)
IMT intake manifold tuning (valve)
IP injector pressure (sensor)
JTIS Jaguar Technical Information System
KS knock sensor (sensor)
LH lefthand
MAF mass air flow (sensor)
N/A normally aspirated
NAS North American specification
OBDII on-board diagnostics stage 2
PAS power assisted steering
PCM powertrain control module
PCV positive crankcase ventilation
PWM pulse width modulated
RH righthand
RPM revolutions per minute
SAE Society of Automotive Engineers (USA)
SCP standard corporate protocol
TAC throttle actuator control (module)
TP throttle position (sensor)
VVT variable valve timing
W watts
AJ-V6/AJ28

V6 EngineAJ-V6/AJ28
5
Engine Specifications
Configuration 60û V6
Displacement 2967 cc (181 cu. in)
Bore 89.0 mm (3.504 in)
Stroke 79.5 mm (3.130 in)
Compression ratio 10.5 :1
Cylinder head 2 overhead camshafts per bank, 4 valve per cylinder
Firing order 1-4-2-5-3-6
Maximum power DIN - 179 kW (240 BHP) at 6800 RPM
EEC - 175 kW (238 PS) at 6800 RPM
Maximum torque DIN - 300 Nm (221 lbft) at 4500 RPM
EEC - 293 Nm (216 lbft) at 4500 RPM
Oil specification see below
Oil volume 5.7 Litres (6 quarts)
Coolant specification see page 35
Coolant volume 10.4 Litres (11 quarts)
Weight 174 kg (384 lbs)
JOL.29550
50JOL.296
Oil Specification
All markets except the USA and Canada
Engine oil for all markets except the USA and
Canada must be to API specification SJ/ACEA A1
or A3.
The recommended SAE viscosity for different
ranges of ambient temperature are shown in
table 1.
USA/Canada
Engine oil for USA and Canada must be to API
specification SJ/ILSAC GF-2.
The recommended SAE viscosity for different
ranges of ambient temperature are shown in
table 2. For maximum economy and in most
climate conditions, SAE 5W/30 is to be preferred
but SAE 10W/30 or 15W/40 are acceptable in
moderate to hot climates.SAE/TEMPERATURE TABLE 2
SAE/TEMPERATURE TABLE 1

V6 EngineAJ-V6/AJ28
15
Oil Cooler and Filter Mounting
The oil filter and oil cooler are mounted slightly
away from the cylinder block on an aluminium
alloy adaptor which is an integral extension of the
LH engine mount. The oil filter is a replaceable
canister screw on type and the cooler is fixed by a
single through bolt to the adaptor. Both
components are connected to the cylinder block
through internal oilways in the adaptor casting
and via an interfacing filter mounting in the
block. A hollow bolt passes through the
adaptor/engine mount and screws into the centre
channel of the block filter mounting to provide
the oil return from the cooler to the cylinder
block.
The adaptor mounted oil cooler is an oil to water
heat exchanger and the coolant matrix is
connected via hoses into the main coolant system
at the radiator bottom hose (see Cooling System).
ENGINE OIL PRESSURE AND OIL TEMPERATURE SENSORS
D.303.1205
OIL COOLER AND FILTER ASSEMBLY
EOP Sensor
EOT Sensor
D.303.1205
D.303.1371
Engine Oil Pressure (EOP) and Oil
Temperature (EOT) Sensors
EOP and EOT sensors are fitted on the LH side of
the cylinder block in the return feed from the oil
cooler. The oil temperature is monitored to
provide data for the VVT system.
Oil Cooler
Hollow Bolt
Engine Mount/
Oil Cooler Adapter

V6 Engine AJ-V6/AJ28
40
Engine Management Sensors
Key to illustration on page 41:
1. Throttle motor
2. TP sensor
3. IAT sensor
4. MAF sensor
5. Top IMT valve
6. Bottom IMT valve
7. EFT sensor
8. IP sensor
9. Fuel injectors
10. Coil-on-plug units
11. VVT shuttle valve
12. CMP sensor
13. CHT sensor
14. KS sensors
15. EOT sensor
16. CKP sensor
17. HO2 sensors
18. HO2 sensors (catalyst monitors)
Cylinder Head Temperature (CHT) Sensor
The single CHT sensor is located between the two
rear coil-on-plug units in the bank 2 cylinder
head. The sensor directly monitors the metal
temperature of the cylinder head. This method of
engine heat sensing is used in place of a
conventional coolant temperature sensor to
enable the fail safe cooling strategy to operate.
The use of a metal temperature sensor allows
cylinder head temperature to be measured even if
coolant has been lost unlike an ECT sensor which
would produce inaccurate temperature
indications, eg measuring steam temperature.
Crankshaft Position (CKP) Sensor
Crankshaft position and rotational speed are
sensed from a steel timing ring keyed to the front
end of the crankshaft immediately behind the
front cover. The timing ring has 36-1 teeth, ie one
missing tooth, which are angled slightly forward
and bent at rightangles to provide a sensing area
for the inductive sensor. The sensor is positioned
in the front cover, to the side of the crankshaft
damper, at approximately 20û to the plane of the
timing ring.
D.303.1342
J.303.1343
CHT SENSOR
CKP SENSOR
D.303-1342
J.303-1343
Engine management sensors and actuators (but
not off engine sensors) are summarised in the
illustration on page 41 and are also described
below or in the relevant section (VVT, fuel system,
throttle, tuned manifold).
The engine management system is described in a
separate section.

V8 EngineAJ-V6/AJ28
45
Introduction
The AJ28 engine is a variant of the 4.0L 90û V8 units fitted to the XJ and XK range of vehicles. The AJ28
shares some of the changes incorporated in the current AJ27 engine: both engines are derived from the
original AJ26 unit. A number of features are unique to the AJ28 or are shared with the AJ-V6 engine also
described in this publication.
Features of the AJ28 engine are:
¥ Continuously variable inlet valve timing over a 48û
+
-2û crank angle: as fitted to the AJ27 engine
¥ Full authority cable-less electronic throttle control: as fitted to the AJ-V6 engine
¥ Air assisted fuel injection: similar to system used on the AJ27 engine
¥ Unique induction manifold with centrally mounted throttle body
¥ Returnless fuel system: similar to AJ-V6 engine
¥ Twin wall exhaust manifold
¥ Engine management system as used on the AJ-V6
¥ New sensors
¥ Modified sump and oil cooler
¥ Modified front end ancillary drive and components
Engine Specification
Maximum power DIN - 209 kW (281 BHP) at 6100 RPM
EEC - 203 kW (276 PS) at 6100 RPM
Maximum torque DIN - 390 Nm (287 lbft) at 4300 RPM
EEC - 278 Nm (279 lbft) at 4300 RPM
Oil Specification
All markets except the USA and Canada
Engine oil for all markets except the USA and
Canada must be to API specification SJ/ACEA A1
or A3.
The recommended SAE viscosity for different
ranges of ambient temperature are shown in
table 1.
USA/Canada
Engine oil for USA and Canada must be to API
specification SJ/ILSAC GF-2.
The recommended SAE viscosity for different
ranges of ambient temperature are shown in
table 2. For maximum economy and in most
climate conditions, SAE 5W/30 is to be preferred
but SAE 10W/30 or 15W/40 are acceptable in
moderate to hot climates.
JOL.29550
50JOL.296
SAE/TEMPERATURE TABLE 2
SAE/TEMPERATURE TABLE 1

V8 EngineAJ-V6/AJ28
47
Cylinder Head
The cylinder head incorporates the modifications
first introduced for the AJ27 engine except for the
camshaft sensor ring and cam cover.
Camshaft Sensor Ring
Cam position sensing is similar to that used on the
AJ27 engine, except that the sensor ring fitted to
each inlet camshaft has five triggering teeth.
Camshaft Covers
To improve accessibility, an extension tube is
fitted to the oil filler hole on the bank 2 cam
cover. Due to the position of the throttle and air
intake ducting, the part load breather outlet is
taken from bank 1 cam cover and the full load
breather outlet from bank 2 (the reverse of AJ27).
Front Cover
The front cover is modified from the AJ27 to
include a mounting boss for a new idler pulley
(see Front End Accessories Drive).
Lubrication
The lubrication system includes the uprated oil
pump (for the linear VVT system) and the same oil
temperature sensor as fitted to the AJ27 engine.
The oil sump and pan are modified as described
on page 46.
The external oil system components are located
laterally across the front of the sump body and
consist of an oil filter, oil cooler and oil filter head
assembly. The oil cooler is an oil to water heat
exchanger similar to the V6 oil cooler and the
cooler matrix is also connected via hoses to a
circulator orifice in the radiator bottom hose (see
Cooling System). The oil filter screws on to the
cooler which connects to the sump body through
an adaptor, the oil filter head assembly.
J.303.1189
CAMSHAFT SENSOR RING
D.303.1189
D.303.1185
CAMSHAFT COVER/OIL FILLER
D.303.1185
D.303.1186
OIL FILTER, COOLER AND ADAPTOR
D.303.1185
Oil temperature sensor
Oil pressure switch
Oil Cooler

V8 Engine AJ-V6/AJ28
54
Engine Management Sensors
The configuration of the AJ28 engine management sensors is changed from the previous V8 variants:
¥ New components unique to AJ28 engine are the MAF sensor and engine fuel temperature (EFT)
sensor.
¥ Components in common with the V6 engine are the IAT sensor, KS sensors, injector pressure (IP)
sensor, engine oil temperature (EOT) sensor and HO2 sensors.
¥ The crankshaft (CKP) and camshaft (CMP) sensors are the same as those fitted to the AJ27 engine.
Heated Oxygen (HO2) Sensors
Upstream and dowmstream HO2 sensors are
fitted and are of the type used on the V6 engine
(the linear type sensor is not used).
J.303.1387
HO2 SENSORS
J.303.1387
J.303.1281
COIL ON PLUG UNIT
J.303.1281
Ignition System
The coil-on-plug ignition modules are specific to
the AJ28 engine and are triggered directly from
the PCM. Double electrode platinum plugs are
fitted.

Automatic TransmissionAJ-V6/AJ28
63 controlled solenoid are mounted on an
integral, replaceable, control module
¥ three speed sensors mounted on the external
casing: turbine speed sensor, intermediate
speed sensor and output speed sensor
¥ an oil temperature sensor is fitted inside the
transmission.
The gear select lever is connected via a Bowden
cable to an operating lever on the left side of the
transmission casing. A digital rotary switch, the
transmission range switch, fits over the shaft of
the operating lever and is fixed by two bolts to
the transmission casing. Selection of a particular
drive function generates a 4 bit binary coded
signal which is transmitted directly to the PCM
over a four wire parallel interface. As on the XK
and XJ Series, lateral movement of the gear select
lever across the gate, D to 4 or 4 to D, operates a
switch which indicates the selected function to
the PCM (the Bowden cable is not actuated
laterally).
The PCM directly controls the transmission
actuators as a response to driver demand, engine
requirements and according to the selected shift
mode. Gear selection is controlled by commands
to the four shift solenoids. If, during gear
selection, the relative speeds monitored by the
speed sensors are not as expected, the PCM
varies the analogue signal to the variable force
solenoids to increase/decrease the clutch pressure
(closed loop control). Increased engagement times
due to ageing are also controlled by adaptive shiftpressure.
Apart from the sports mode and traction mode
selected by the driver, there are pre-programmed
modes selected by the PCM in response to sensed
driving conditions :
¥ increased load such as gradients and trailer
towing
¥ cruise control
¥ hot mode: strategies including clutch lock up
are applied to reduce heat.
Transmission Oil Cooler
The transmission fluid is cooled externally by a
dedicated oil to air radiator which is mounted in
the integral cooling pack between the engine
radiator and A/C condenser and below the PAS
cooler.
D.307.320
TRANSMISSION OIL COOLING
Transmission
Oil Cooler
D.307.320