fuses JAGUAR S TYPE 2005 1.G Electrical Manual
[x] Cancel search | Manufacturer: JAGUAR, Model Year: 2005, Model line: S TYPE, Model: JAGUAR S TYPE 2005 1.GPages: 200, PDF Size: 5.93 MB
Page 11 of 200
DATE OF ISSUE: May 20047
IntroductionJaguar S-TYPE 2005
Electrical Guide Format
This Electrical Guide is made up of two major sections:
the first section, at the front of the book, provides general information for and about the use of the book; model-specific information and illustrations to aid in the understanding of the electrical / electronic systems, as well as the location and
identification of components.
the second section includes the Figures, which are the basis of the book. Each Figure is identified by a Figure Number (e.g. Fig. 01.1) and Title. The page adjacent to the Figure contains data information specific to that Figure.
NOTE: Data pages are not available for inclusion in Provisional versions of the Electrical Guide.
It is recommended that the user read through the front section of the book to develop a familiarity with the layout of the book and with
the system of symbols and abbreviations used. The Table of Contents should help to guide the user.
Vehicle Identification Numbers (VIN)
VIN ranges are presented throughout the book in the following manner:
➝ VIN 123456 indicates ‘up to VIN 123456’; VIN 123456 ➝indicates ‘from VIN 123456 on’.
Electrical System Architecture
Power Supplies
The electrical system is a supply-side switched system. The ignition switch directly carries much of the ignition switched powe r
supply load.
Power supply is provided via three methods:
Direct battery power supply;
Ignition switched power supply;
Switched system power supply.
The ‘Switched System Power Supply’ circuit is controlled via the FEM (Front Electronic Module) and the REM (Rear Electronic
Module). Refer to Fig. 01.6 for circuit activation details.
Fuse Boxes
The electrical harness incorporates two hard-wired power distribution fuse boxes:
the Front Power Distribution Fuse Box, located in the engine compartment;
the Rear Power Distribution Fuse Box, located in the trunk.
A serviceable Primary Junction Fuse Box is located in the front right-hand foot well. All fuses and relays (except the trailer towing
accessory kit) are located in the two fuse boxes.
Vehicle Networks
Three different networks are employed:
CAN (Controller Area Network) for high-speed power train communications;
SCP (Standard Corporate Protocol) network for slower speed body systems communications;
D2B (Optical) Network for very high-speed ‘real-time’ audio data transfer.
NOTE: The D2B Network is a fiber optic network with a gateway to the remaining vehicle networks via the Audio Unit. Technician
access to the three networks and the Serial Data Link is via the Data Link Connector.
Ground Studs
Circuit ground connections are made at body studs located throughout the vehicle. There are no separate power and logic groundi ng
systems; however, there are a certain number of components that use unique ground points.
Page 13 of 200
DATE OF ISSUE: May 20049
User InstructionsJaguar S-TYPE 2005
Battery; Starter; Generator: V6Battery; Starter; Generator: V6
VARIANT: V6 Vehicles
VIN RA NGE: All
DATE OF ISSUE: February 2004f02_1_200045
Y
FPDB MEGAFUSE
STARTER MEGAFUSEMEGAFUSE ASSEMBLYBATTERY
FAULT;
CHARGE WARNING
B
JB1
CA288 CA280 CA304450A
250A CA302
CA135
R
R
R
R01.1REAR POWER DISTRIBUTION
FUSE BOX
WUKEY-IN0FC18-5
I
II
III
FC18-7
FC18-4
NR7
IGNITION SWITCHFC18-1
WG
WB01.5IGNITION SWITCHED
CIRCUITS (II)
NG56S FC52-1
PASSIVE ANTI-THEFT SYSTEM TRANSCEIVER
FC52-3
FC52-4
FC52-2WR YRBG
WU
FC37-3 FH53-3
FHS63
PI41-34
F1 5AYYY
PRIMARY JUNCTION FUSE BOX
GB2-9
GB2-10GB1-10GB1-9
GB2-13
GB2-16GO
GRBB
BB BB+O
P
P, N
P18II
PIS30 PI40ALTRANSMISSION CONTROL MODULE
92NR GR GR GR GRCA286-1 CA286-2 FH3-10PI42-8 GB1-13CLUTCH PEDAL SAFETY SWITCH
85NG
WG35II FC8-14 FC8-15
FC9-31 FC9-16 FC9-32FC8-5PASSIVE
ANTI-THEFT
SYSTEM
LOGICB+B+
C
C
D I
D P
P
INSTRUMENT CLUSTER
YFC9-28GFC9-29BFC8-32BFC8-2
FC38
20.1 20.1O.K .TO START
YYPIS27 GB1-14(MAN / ROW)(MAN / NAS) (AUTO)
JUNCTION BLOCKST11 ST12R3
FRONT BULKHEADFH83
CA177FH672
STARTER RELAY
NW
GW
GO65ST4-1
R20
FRONT POWER DISTRIBUTION FUSE BOX
PI41-40
STARTER MOTORR
B R
GW
ST5
ST6
ST3
ST2
GB1-6 PI1-41
PI1-31 PI1-6
PI1-124
PI1-123
GO GR Y
GENERATOR WARNING; CLUTCH DISENGAGEDY
G20.1 20.1
P, NSTART
ENGINE
CRANK
ENGINE
REQUESTO
I
II
I
O
C
C
ENGINE CONTROL MODULE
PI1-65
PI1-53
PI1-79 PI47-3
PI47-2
PI47-1
PI47-4WG YR
WR GO
20IIB+ST7
FIELD
CONTROL
GENERATOR
13 4
114
46 80
76 77 92ll15 45ll ll SS81 118EEFig. 01.1
Fig. 01.2 Fig. 01.3
Fig. 01.4
Fig. 01.5Fig. 01.6
Fig. 01.7Input
OutputI
OB
P+Battery Voltage Power Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN+SCPC
S DD–D2B Network2
Fig.
02.1
Fig. 02.1
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all ciruit connections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
IInput
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
SSCPNetwork
D2 D2B Network
D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furhished to aid the user in understanding circuit operation. THIS INFORMATION SHOULD BE USED FOR
REFERENCE ONLY. Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
DATE OF ISSUE: February 2004
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description Location
BATTERY —— LUGGAGECOMPARTMENT
CLUTCH PEDAL SAFETY SWITCH CA286 2-WAY / BLACK TOP OF CLUTCH PEDAL (BOTTOM SWITCH)
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, PASSENGER SIDE
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
GENERATOR (V6) PI47 4-WAY / BLACK ENGINE, RH SIDE, FRONT ST7 EYELET
IGNITION SWITCH FC18 7-WAY / BLACK STEERING COLUMN COWLING
INSTRUMENT CLUSTER FC14 22-WAY / GREY INSTRUMENT PANEL FC15 20-WAY / BLACK
FC63 22-WAY / BLACK
PASSIVE ANTI-THEFT SYSTEM TRANSCEIVER FC52 4-WAY / GREEN STEERING COLUMN, IGNITION SWITCH
PRIMARY JUNCTION FUSE BOX CA2 26-WAY / BLACK RH ‘A’ POST
CA56 8-WAY / BLACK
FC37 26-WAY / BLACK
FH7 6-WAY / BLACK
FH53 10-WAY / BLACK
STARTER MEGAFUSE — — LUGGAGE COMPARTMENT
STARTER MOTOR — — ENGINE BLOCK, RH SIDE
STARTER RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R20
TRANSMISSION CONTROL MODULE GB2 16-WAY / BLACK TRANSMISSION CONTROL VALVE ASSEMBLY
HARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
GB1 16-WAY / GREY / ENGINE HARNESS TO TRANSMISSION HARNESS ADJACENT TO TRANSMISSION BELL HOUSING
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDE
PI42 8-WAY / BLACK / ENGINE HARNESS TO FRONT HARNESS ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDE
ST4 2-WAY / GREY / FRONT HARNESS TO STARTER LINK ENGINE COMPARTMENT, REARWARD OF RH WHEEL ARCH
GROUNDS
Ground LocationFC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
JB1 LUGGAGE COMPARTMENT, BATTERY GROUND
PI40(LHD) ENGINECOMPARTMENT,BEHINDRHWHEELARCHLINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
ST2 ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Engine Control Module Pin Description and Characteristic
IPI1–6 ENGINECRANK:B+
I PI1–31 AUTOMATIC – PARK / NEUTRAL SIGNAL: B+ WHEN ACTIVATED MANUAL, ROW – PARK / NEUTRAL SIGNAL: B+ WHEN IGNITION CRANK (III)
MANUAL, NAS – CLUTCH PEDAL SAFETY SWITCH (PARK / NEUTRAL SIGNAL): B+ WHEN ACTIVATED
O PI1–41 STARTER RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–53 FUEL PUMP 2 DRIVE (TO FUEL PUMP 2 MODULE): PWM, 150 Hz, NORMAL POSITIVE DUTY CYCLE RANGE = 4% – 51%
I PI1–65 GENERATOR FIELD RETURN SIGNAL: VARIABLE VOLTAGE BY GENERATOR OPERATING CONDITION
I PI1–79 GENERATOR FAULT; CHARGE WARNING
C PI1–123 CAN –
C PI1–124 CAN +
Instrument Cluster
Pin Description and CharacteristicI FC14–2 KEY-IN AUDIBLE WARNING: B+ WHEN KEY IN
B+ FC14–3 IGNITION SWITCHED POWER SUPPLY (II): B+
SG FC14–14 SIGNAL GROUND: GROUND
PG FC15–2 POWER GROUND: GROUND
B+ FC15–3 BATTERY POWER SUPPLY (LOGIC): B+
I FC15–4 PATS GROUND: GROUND
D FC15–5 PATS TRANSCEIVER: ENCODED COMMUNICATION
D FC15–6 PATS TRANSCEIVER: ENCODED COMMUNICATION
C FC15–18 CAN +
C FC15–19 CAN –
Transmission Control ModulePin Description and CharacteristicB+ GB2–9 IGNITION SWITCHED POWER SUPPLY: B+
O GB2–10 PARK / NEUTRAL SIGNAL: GROUND WHEN ACTIVATED
PG GB2–13 POWER GROUND: GROUND
PG GB2–16 POWER GROUND: GROUND
CONTROL MODULE PIN OUT INFORMATION FIGURE NUMBERCOMPONENT, CONNECTOR AND GROUND
INFORMATION
DATE OF ISSUE
FIGURE MODEL RANGE AND YEAR
TITLE FIGURE NUMBER
KEY TO REFERENCE SYMBOLS VARIANT, VIN RANGE AND DATE OF ISSUE
DATA PAGE
FIGURE PAGE
Page 16 of 200
12DATE OF ISSUE: May 2004
Symbols and CodesJaguar S-TYPE 2005
Grounds
On figures where LHD and RHD circuits are combined and the ground designation differs from LHD to RHD, the RHD ground code is
shown in parentheses. If the ground designation is the same for LHD and RHD, only one ground code is used, with no parentheses.
Relays
All relays are located in the Front and Rear Power Distribution Boxes and the Primary Junction Fuse Box. Relays do not have a
separate relay connector (base). All relays use the ISO pin numbering system (1, 2, 3, 4, 5). Each relay is identified by an ‘R’number
unique only to the fuse box in which it is located.
Fuses
All fuses are located in the Front and Rear Power Distribution Boxes and the Primary Junction Fuse Box. Each fuse is identified by
an ‘F’ number unique only to the fuse box in which it is located.
Networks
In most instances, networks are shown as a broken grey line to indicate that there is network communication between the depicte d
control modules. Refer to Fig. 20.1, Fig. 20.2, Fig. 20.3, Fig. 20.4 and Fig. 20.5 for circuit details.
Component Depictions
G30AS
(G26AS)G31BL
EXAMPLE:LHD Vehicles
RHD Vehicles Same for LHD and RHD Vehicles
3
1 5
2
R643
1 5
2
R2
CHANGE-OVER RELAY NORMALLY OPEN RELAY
EXAMPLE:
F19 15A
EXAMPLE:
S
SIP5-2 IP5-1
20.2
20.220.2
IP10-1
IP10-2S
SU Y
U Y
20.2
SCPEXAMPLE:
CONTROL MODULE CONTROL MODULE
MESSAGE(S) MESSAGE(S)
MESSAGE(S)
MESSAGE(S)
COMPLETE COMPONENTS
AND CONTROL MODULES INCOMPLETE COMPONENTS
(EXCEPT CONTROL MODULES) ASSEMBLIES AND
POWER DISTRIBUTION FUSE BOXES COMPONENTS WITH
INTERNAL ELECTRONIC CIRCUIT
EXAMPLE:
Page 38 of 200
DATE OF ISSUE: May 2004
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
Fig. 01.1
COMPONENTS
Component Connector(s) Connector Description Location
BATTERY — — LUGGAGE COMPARTMENT
FPDB MEGAFUSE — — LUGGAGE COMPARTMENT
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
IGNITION SWITCH FC18 7-WAY / BLACK STEERING COLUMN COWLING
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENT
REAR POWER DISTRIBUTION FUSE BOX MEGAFUSE — — LUGGAGE COMPARTMENT
STARTER MEGAFUSE — — LUGGAGE COMPARTMENT
TRANSIT ISOLATION RELAY CA16 2-WAY / WHITE LUGGAGE COMPARTMENT, BATTERY + POST
HARNESS IN-LINE CONNECTORS
Connector Connector Description / Location Location
FC39 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
GROUNDS
Ground Location
JB1 LUGGAGE COMPARTMENT, BATTERY GROUND
Page 40 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.DATE OF ISSUE: May 2004
Fig. 01.2
COMPONENTS
Component Connector(s) Connector Description LocationFRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationDM22 4-WAY / GREY / CABIN HARNESS TO DRIVER SEAT HARNESS UNDER DRIVER SEAT
DM23 20-WAY / BLACK / CABIN HARNESS TO DRIVER SEAT HARNESS UNDER DRIVER SEAT
DT8 14-WAY / GREY / CABIN HARNESS TO DRIVER DOOR TRIM HARNESS DRIVER DOOR
FC39 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDE
PN23 4-WAY / GREY / CABIN HARNESS TO PASSENGER SEAT HARNESS UNDER PASSENGER SEAT
PN24 20-WAY / BLACK / CABIN HARNESS TO PASSENGER SEAT HARNESS UNDER PASSENGER SEAT
PT1 14-WAY / GREY / CABIN HARNESS TO PASSENGER DOOR TRIM HARNESS PASSENGER DOOR
Page 42 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.DATE OF ISSUE: May 2004
Fig. 01.3
COMPONENTS
Component Connector(s) Connector Description LocationPRIMARY JUNCTION FUSE BOX CA2 26-WAY / BLACK RH ‘A’ POST
CA56 8-WAY / BLACK
FC37 26-WAY / BLACK
FH7 6-WAY / BLACK
FH53 10-WAY / BLACK
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
SL3 10-WAY / GREY / FASCIA HARNESS TO SOLAR SENSOR LINK BEHIND INSTRUMENT PANEL, RH SIDE
Page 44 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.DATE OF ISSUE: May 2004
Fig. 01.4
COMPONENTS
Component Connector(s) Connector Description LocationIGNITION SWITCH FC18 7-WAY / BLACK STEERING COLUMN COWLING
PRIMARY JUNCTION FUSE BOX CA2 26-WAY / BLACK RH ‘A’ POST
CA56 8-WAY / BLACK
FC37 26-WAY / BLACK
FH7 6-WAY / BLACK
FH53 10-WAY / BLACK
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC39 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
Page 46 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.DATE OF ISSUE: May 2004
Fig. 01.5
COMPONENTS
Component Connector(s) Connector Description LocationFRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
IGNITION SWITCH FC18 7-WAY / BLACK STEERING COLUMN COWLING
INERTIA SWITCH CA4 3-WAY / GREY LH ‘A’ POST
PARKING BRAKE MODULE CA241 4-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA242 12-WAY / BLACK
PRIMARY JUNCTION FUSE BOX CA2 26-WAY / BLACK RH ‘A’ POST CA56 8-WAY / BLACK
FC37 26-WAY / BLACK
FH7 6-WAY / BLACK
FH53 10-WAY / BLACK
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationDM23 20-WAY / BLACK / CABIN HARNESS TO DRIVER SEAT HARNESS UNDER DRIVER SEAT
FC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC39 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
GB1 16-WAY / GREY / ENGINE HARNESS TO TRANSMISSION HARNESS ADJACENT TO TRANSMISSION BELL HOUSING
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDE
PN24 20-WAY / BLACK / CABIN HARNESS TO PASSENGER SEAT HARNESS UNDER PASSENGER SEAT
RF34 16-WAY / GREEN / CABIN HARNESS TO DOOR HARNESS ‘D’ POST, UNDER PARCEL SHELF
Page 50 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 01.7
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationEMS CONTROL RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R4
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
HO2S RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R2
IGNITION COIL RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R3HARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationCP1 10-WAY / BLACK / INTERCOOLER PUMP LINK LEAD ENGINE COMPARTMENT, RH FRONT, ADJACENT TO RADIATOR
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
IL10 12-WAY / BLACK / ENGINE HARNESS TO FUEL INJECTOR LINK REAR OF ENGINE
IS5 6-WAY / BLACK / ENGINE HARNESS TO FUEL INJECTOR LINK ENGINE, LH REAR
IS6 6-WAY / BLACK / ENGINE HARNESS TO FUEL INJECTOR LINK ENGINE, RH REAR
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationFH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
Engine Control Module Pin Description and CharacteristicO PI1–40 EMS CONTROL RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
Page 52 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 01.8
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationEMS CONTROL RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R1
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
POWERTRAIN CONTROL MODULE C98 48-WAY / BROWN FRONT BULKHEAD, PASSENGER SIDE
C99 48-WAY / GREY
FH13 48-WAY / BLACK
Powertrain Control ModulePin Description and CharacteristicO FH13–J3 EMS CONTROL RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND