bulb JAGUAR S TYPE 2005 1.G Technical Guide Update

JAGUARS-TYPEBody
14
Hood
Unlike current Jaguar cars, the hood is hinged at
the rear with single pivot hinges and gas struts. It
has two primary and one secondary latch for
security. The primary latches are joined with an
intermediate cable and release of the primary
latches is by a single cable from the hood release
lever on the driver side of the vehicle. The two
primary latches are handed for LHD and RHD
vehicles. The secondary latch, mounted on the LH
side of the hood between the grille and inner
headlight, is provided for added safety and must
be hand released before the hood can be fully
opened. Hood sealing comprises front and rear
lengths of sponge bulb, pegged to the hood inner.
JOL.091
HOOD RELEASE AND OPENING
JOL.091
JOL.030
FUEL FILLER FLAP
JOL.031
FUEL FILLER FLAP MANUAL RELEASE
Fuel Filler Flap
The fuel filler flap/cap is located on the rear upper
part of the right fender. Fuel filler flap operation is
via an illuminated switch on the fascia or
emergency manual release by tag and wire in the
RH side of the luggage compartment. The cap,
when removed from the filler neck, is held by a
retaining strap which can be passed over the hook
on the flap to allow easy access for filling the tank
and to prevent scratching of the surrounding
paintwork.
D.501.1787
HOOD RELEASE LATCH

JAGUARS-TYPEBody
16
Cool Air Inlet
The climate control air intake is through a plastic
moulding attached to the engine compartment
bulkhead. This moulding contains the air/pollen
filter and is provided with water drains. It is
covered by a leaf screen. The air intake cover is
held on with a two piece plastic fastener (see
illustration).
D.501.1788
Trunk
The steel trunk lid has two hinges with one
damper and covered springs to assist lid lift. The
lid can be released using the switch on the fascia,
using the key-ring transmitter, or, if the vehicle is
unlocked, by a release button on the lid. An
emergency lock, key operated, is provided for
access to the trunk if, for instance, the battery is
disconnected. The trunk lock barrel is mounted to
the trunk lid with two flange nuts. Drive to the
trunk latch is via a cable which is a snap fit to the
rear of the barrel. Trunk sealing is a simple flange
mounted bulb section with a single moulded joint.
JOL.154
TRUNK RELEASE
Release Button
Emergency Lock
COOL AIR INLET COVER/LEAF SCREEN

JAGUARS-TYPEElectrical/Electronic
86
Exterior Lighting
The exterior lighting switch located on the fascia,
operates the headlamps, sidelights, fog lamps and
the delay variable timer switch. Each headlamp
assembly consists of two headlamp units, the
main beam lamp unit is the inner and the dipped
beam, front parking (side) lamp and the direction
indicator lamp unit is the outer.
Fog lamps are located in recesses in the front
bumper. The two retaining screws are located
behind the anti-theft cover and splitter vane.
J.418.442
Each rear lamp assembly incorporates a tail/stop
lamp and an auxiliary tail lamp, a fog lamp, a
reversing lamp and a direction indicator lamp.
Access for bulb replacement is from the luggage
compartment. The high mounted stop lamp is
powered via the stoplamp switch, it is clipped to
the rear screen and is replaceable as a unit.
The side repeater lamps (where fitted) are located
within the front fender. The sidemarker lamps are
located with the rear and front bumper and are
EXTERIOR LAMPS
High Mounted Stop Lamp
Number Plate Lamps
Inner Headlamp
Unit
Outer Headlamp
Unit
Front Fog Lamp
Side Marker Lamp
Side Repeater Lamp
(where fitted)
Side Marker Lamp
Rear Lamp Assembly
J.418.441 & 442

JAGUARS-TYPEElectrical/Electronic
87
Bulb renewal
It is important that only Jaguar bulbs of the type
specified are used when renewing bulbs.
Before renewing bulbs, switch off the ignition and
light switches.
Top cover
To gain access to the headlamp units, the top
cover must be removed.
Turn the four fasteners a quarter turn anti-
clockwise and then remove the top cover.
After changing the defective bulb, refit the cover
and turn the fasteners clockwise to retain the
cover.
JOL.073
supplied as part of a high level bumper assembly
(the side markers are located in the bumper by
tangs on one side of the unit and held in position
by a spring clip on the other side).TOP COVER

JAGUARS-TYPEElectrical/Electronic
88
JOL.074
Headlamp - Bulb Renewal
The bulbs are halogen type and will be damaged if
touched by hand or contaminated with oil or
grease. It is important to use clean gloves or cloth
when handling a bulb which is to be used again. A
contaminated bulb may be cleaned with
methylated spirit before refitting.
JOL.116
Dipped Beam (outer) Headlamp
Open the bonnet.
Remove the top cover.
Turn the circular cover (A) anti-clockwise and
remove.
Press the spring clip (B) towards the bulb and
downwards to release the bulb. Remove the
bulb/connector (C) from the headlamp assembly.
Pull the connector from the bulb.
Attach the connector to the new bulb, type H7 for
dipped beam, and fit to the headlamp. The bulb
will only correctly fit in one position.
Engage the spring clips to retain the bulb and then
fit the circular cover.
Refit the top cover and close the bonnet.
Have the headlamp aim checked after bulb
replacement.
Main Beam (inner) Headlamp
Open the bonnet.
Remove the top cover.
Turn the bulb holder a quarter turn anti-clockwise
and remove the bulb and holder from the lamp
unit.
Fit a new bulb to the holder, type HB3 for main
beam.
Fit the holder to the lamp unit, the bulb will only
correctly fit in one position.
Refit the top cover and close the bonnet. HEADLAMP - DIPPED BEAM
HEADLAMP - MAIN BEAM
ABC

JAGUARS-TYPEElectrical/Electronic
89
JOL.078
JOL.079
D.417.108
Front Direction Indicator - Bulb Renewal
Remove the top cover.
The bulb is contained within the outer headlamp.
Turn the holder a quarter turn anti-clockwise and
remove the bulb and holder.
Remove the bulb and fit a new one of the correct
type, PY21W.
Fit the holder to the lamp unit, it will only fit in
one position.
Refit the top cover and close the bonnet.
Front Parking (side) Lamp - Bulb Renewal
Open the bonnet.
Remove the top cover.
The front parking lamps are contained within the
outer headlamp units.
Rotate the bulb holder anti-clockwise and remove
from the headlamp.
Pull the capless bulb from the holder and fit a
new one of the correct type, W5W.
Reposition the bulb holder in the headlamp unit
and turn clockwise.
Refit the top cover and close the bonnet.
Front Fog Lamp - Bulb Renewal
Remove bumper splitter vane and blackout panel.
Unscrew fixing; remove lamp from front.
Twist/remove bulb carrier.
Remove the bulb and fit a new one of the correct
type, H3.
Refit the bulb carrier, fixing, blackout panel and
splitter vane.FRONT DIRECTION INDICATOR AND PARKING LAMPS
FRONT FOG LAMP
Front Parking
Lamp
Front Direction
Indicator Lamp
JOL.078 & 079

JAGUARS-TYPEElectrical/Electronic
90Side Repeater Indicator - Bulb Renewal
Remove the lamp unit from the front wing panel
by pressing the unit forwards or rearwards to
compress the spring clip and remove the complete
unit.
Twist the bulb anti-clockwise and remove.
Fit a new bulb of the correct type, W5W.
Press the unit into the recess until it clicks into
place.
JOL.076
JOL.075
Rear Lamp Assembly - Bulb Renewal
The rear lamp assembly has the following bulbs:
¥ Reverse lamp, type P21W.
¥ Stop/tail lamp, type P21/4W.
¥ Fog lamp, type P21W
¥ Tail lamp, type R5W.
¥ Direction indicator, type PY21W.
Ensure that the lamps and ignition switch are OFF
before removing any bulbs.
Open the luggage compartment, loosen the side
carpet and unclip the rear lamp bulb carrier.
Remove the faulty bulb and fit a new one of the
correct type, as illustrated on the bulb holder.
Fitment of the correct type is essential.
Refit the bulb carrier assembly, ensuring that the
clips are correctly secured.
Refit the carpet. SIDE REPEATER INDICATOR
REAR LAMP ASSEMBLY
Direction Indicator
Tail Lamp
Stop/Tail Lamp
Fog Lamp
Reverse Lamp

JAGUARS-TYPEElectrical/Electronic
91
JOL.077
High Mounted Stop Lamp
Remove the rear parcel tray trim panel.
Depress clips to remove from pegs.
Number Plate Lamp - Bulb Renewal
Push the lens clip sideways and remove the lens
from the vehicle.
Remove the bulb and fit a new one of the correct
type, W5W.
Refit the lens by pressing it firmly into the recess
until it clicks into place.NUMBER PLATE LAMP
J.418.447
EXTERIOR LIGHTING CONTROLS
Exterior Lighting
Switch
LH Column
Switchgear
Lighting Stalk
Hazard Switch
Autolamp
Sensor
Instrument
Pack
To
General Electronic
Control Module
To
Rear Electronic
Control Module

JAGUARS-TYPEElectrical/Electronic
95
Instrumentation and Controls
1. Instruments pack
2. Wipers/washers and headlamp power
wash switches,
3. Trip computer switches,
4. Hazard warning switch,
5. Audio system control panel,
6. Cassette stowage, telephone presenter or
navigation display,
7. Climate control panel,
8. Ashtray and cigar lighter,
9. Traction control or dynamic stability
control switch,
10. Sports mode switch,
11. Front seat heater switches,
12. Coin tray,
13. Cruise control switches,
14. Horn and driverÕs airbag,
15. Audio switches,
16. Dimmer switch,
17. Bonnet release lever,
18. Headlamp levelling switch,
19. Fuel filler flap release switch,
20. Luggage compartment release switch,
21. Exterior lighting switch,
22. Direction indicators and main beam
switches,
1
7
8
9 10 11 12 13 19
16 17 18 20 21 22
142
3
45
6
15
Instrument Pack
Vehicle instrumentation is installed on the
instrument pack on the fascia. The calibration of
the odometer and speedometer, the language of
the message center and the composition of the
indicator lamps are tailored to suit the destination
market. The instrument pack acts as a system
monitor for the audible and visual warnings.When the ignition switch is turned to position II,
the following visual warnings (telltales) are
illuminated for three seconds to provide a bulb
prove out function:
¥ ABS telltale
¥ Airbag telltale (six seconds prove out)
¥ Catalyst over temperature telltale (Japan only)
¥ Charging system telltale

JAGUARS-TYPEElectrical/Electronic
100
Exterior Lighting Switch
A. Timer
B. Auto
C. Off
D. Side (parking lamps)
E. Headlamps
F. Rear fog lamps
G. Front fog lamps (where fitted)
Autolamps Delayed Exit (A)
This feature leaves the headlamps turned on after
the ignition has been switched off, allowing the
driver and passengers increased visability on
leaving the vehicle. The switch has seven positions
and varies the time from three seconds up to
three minutes. After adjustment, the newly set
delay time will be displayed on the message
center.
Auto (B)
A light sensor on top of the instrument panel,
monitors exterior light levels and automatically
switches the side lamps and dipped headlamps on
or off. When light fades to the non-adjustable
preset level, the sidelamps and headlamps switch
on automatically. As light increases to the preset
level, the sidelights and headlamps switch off
automatically.Rear Fog Lamps (F)
Turn the switch to headlamps on, pull the switch
and then turn to position (F). Turning on the rear
fog lamps will also turn on the front headlamps.
Front Fog Lamps (G)
Pull the switch in positions (A), (B), (D) or (E) to
switch on the front fog lamps. Push to turn off. If
the rotary switch is turned off (C) the switch will
be retracted to its normal position and the fog
lamps will be turned off.
Daylight Running Lamps
In certain countries it is a legal requirement for
the lamps to be on during the hours of daylight.
With the rotary switch in the off position (C),
dipped headlamps, sidelights and tail and number
plate lamps will switch on automatically when the
ignition is turned to position II, the vehicle is out
of park (automatic transmission only) and the
parking brake is released.
Battery Saver
If the dipped or main beam headlamps are
switched on and the ignition is turned to OFF or
the key is removed, the lamps will automatically
turn OFF after 10 minutes. The sidelights will
remain ON.
Bulb Failure Monitoring
The tail and brake lamp bulbs are monitored for
failure and a corresponding message is shown in
the message center, e.g ÔLEFT TAIL LAMP FAILEDÕ.
There are two tail lamp bulbs in each tail lamp.
The message that a tail lamp has failed indicates
that both bulbs in that cluster have failed. The
message will be shown, even after a bulb is
replaced, until the next time the bulb is switched
on.
JOL.069
EXTERIOR LIGHTING SWITCH
A
F E D C
B
G