fog light JAGUAR XF 2013 1.G Quick Start Guide

JAGUAR XF JAGUAR XF JAGUAR XF
JAGUAR XF JAGUAR XF JAGUAR XF
Warning lamps Displayed on the instrument panel
Electric parking brake See page 2, item 19
Auto headlamps and wipers See page 2, items 1 and 7
Starting and driving
6 Releasing
With the ignition on, apply the foot brake and press
• down on the parking brake lever.If the vehicle is stationary with the parking brake
• applied and either Drive or Reverse selected, pressing
the accelerator will automatically release the parking
brake.
Note: Do NOT use the recess in the electric parking
brake as a storage area.
Cruise control and forward alert See page 2, items 5 and 29
Starting and driving
7
Braking system fault or brake fluid low Braking system fault or
brake fluid low. USA only
Dynamic stability control.
Flashes when DSC is
operating
DSC switched off, Trac
DSC on
Automatic speed limiter
active Seat belt reminder Low tire pressure
Anti-lock braking system
fault. Anti-lock braking system
fault. USA only
Engine malfunction
Applying With the vehicle stationary, lift up the parking brake
• lever and then release it. The red warning indicator in the
instrument panel will illuminate.
Operating note
The brake must be manually applied when parking.
Cruise control override
Cruise control disengages when brakes are applied or
when speed is below 18mph (30 km/h).
Auto high beam
1. When AUTO is selected on the lighting control the
side lamps and headlamps will turn on automatically
when ambient light fades. With the control in the low
beam position, high beam will activate automatically when
ambient light falls below a pre set level. Vehicle speed
must be above 25 mph (40 km/h).
Exit delay
2, 3, 4. The headlamps can be set to temporarily light
your way when you exit the car at night. Rotate the control
for exit delay periods of 30 seconds, 60 seconds or 120
seconds.
1
432
MA X
MIN
MAX
MIN
6
5
7
Auto wipers
Automatic wipers are activated by a rain sensor. When
the wiper control is moved up to the first position the
wipers will operate automatically as required. Sensitivity
can be adjusted.
5. First stop for auto position.
6. Rain sensor maximum sensitivity.
7. Rain sensor minimum sensitivity.
Setting cruise control speed
Use to set cruise speed or increase/decrease 1.
speed while cruise control is operating.
Resumes the set speed after a cancellation.
2.
Cancels current setting but retains in memory.3.
automatically slow down and then maintain your set gap
until the road ahead clears. At that point your vehicle will
accelerate to the set cruise control speed.
ACC gap setting
4. Press to increase or decrease the set gap to the
vehicle ahead. An amber warning icon will illuminate in
the instrument panel. The Message center will display the
current set gap. There are 4 gap settings to choose from.
Forward alert
An additional feature of ACC, forward alert provides
limited detection of objects in the road ahead. When
necessary it will give an audible warning plus the visual
warning FORWARD ALERT in the Message center. The driver must take appropriate action.
5. Press to activate the Forward Alert function.
The Forward Alert icon will illuminate in the instrument
panel.
Sensitivity of detection can be adjusted. With ACC
disengaged, use the GAP SETTING control 4 to adjust
the setting.
Adaptive cruise control (ACC)
ACC can be programmed to maintain a set gap to the
vehicle ahead. If the vehicle ahead is traveling slower
than your set cruise control speed, your vehicle will
Driver intervention
ACC IS NOT a collision warning or avoidance
system. Additionally the system WILL NOT detect:
Stationary vehicles or vehicles moving at below • 6 mph (10 km/h).
Pedestrians or objects in the roadway.•
Oncoming vehicles in the same lane.•
Automatic car wash
Before entering an automatic car wash, turn the
wipers off to deactivate the rain sensor. Otherwise,
the wipers will operate during the washing process
and may be damaged.

4
32
1
5
Air bag fault
Rear fog lamp on
Forward alert active
Adaptive cruise control
active
Automatic speed limiter (ASL) See page 2, item 18
ASL allows any speed between 18 to 150 mph (30 km/h
to 240 km/h) to be set as a maximum speed. This is
useful to ensure any given speed limit is not exceeded.
Setting a speed
The setting procedure can be made
while the vehicle is stationary.
Press the
1. ASL button. An ASL warning lamp illuminates in the instrument panel.
Use the cruise control + and - 2. controls to set a speed. The Message center will display the set speed. Adjustment can be made at any time to suit variable speed limits. If ASL is cancelled due to kick down acceleration or by
pressing the cruise control CANCEL, the Message center
will display a ‘LIMITER CANCELLED’ message.
Press the RESUME control to reinstate the ASL set
speed.
ASL
Driver intervention
When negotiating a steep downhill gradient, vehicle
speed may exceed the set speed. The Message
center will display a warning.
JJM189640131.indd 6-701/08/2012 13:45:11