length JAGUAR XF 2013 1.G Quick Start Guide

JAGUAR XF JAGUAR XF JAGUAR XF
JAGUAR XF JAGUAR XF JAGUAR XF
Setting the driving position See page 2, items 25, 30 and 31 Engine start/stop See page 2, item 22
Transmission See page 3, items 2, 6 and 16
Restraints
Comfort adjustments Starting and driving
5
4 Driver’s seat
Set the seat position using the following controls.
Cushion length.
1.
Side bolster - inflate.2.
Side bolster - deflate.3.
Lumbar support.4.
Seat back angle and head restraint.5.
Seat forwards and back, cushion height and cushion 6. angle.
Note: Seat heater controls are accessed via the touch
screen.
Steering column
With the vehicle stationary, adjust the steering column
7. to your ideal driving position.
Door mirrors
1. Press the left or right mirror selector.
2. Use the mirror adjuster to set mirror position.
Storing the driving position to memory
Once you have adjusted the driver’s seat, steering
column and door mirrors for your ideal driving position,
the settings can be stored.
8. Press the SET button to activate the memory store
function. The button will illuminate to indicate the memory
store function is active.
9. Within 5 seconds, press button 1 or 2 to store the
current driving position.
A stored memory position can now be recalled with a
press of the appropriate button; 1 or 2. The seat, steering
wheel and mirrors will move to their preset positions.
Operating note
Memory buttons must be pressed within 5 seconds
after pressing the SET button otherwise the memory
store function will cancel.
Operating note
The engine will continue to run even if the Smart
Key is removed from the vehicle by more than 3ft (1
metre). However, if the engine is stopped, it cannot
be restarted until the Smart Key is returned to the
vehicle.
Operating note
If the engine is switched off with Neutral selected,
automatic selection of P is delayed for 10 minutes.
DO NOT use this feature to enable towing of the vehicle. Refer to Vehicle recovery in the Owner’s
Handbook.A warning indicator on the instrument panel will illuminate if the seat belt of an occupied
front seat is not fastened. This may be
accompanied by an audible warning.
Using child seats
Refer to Child Seats in the Owner’s Handbook to
determine the correct seat for your child.
If it becomes necessary to fit a child restraint on the front
passenger seat, make the following seat adjustments. Move the seat fully rearward.•
Lumbar support to minimum setting.•
Seat cushion to highest position.•
Cushion front tilt to lowest position.•
Seat back to upright position.•
Adjust the upper seat belt anchorage to its lowest • position.
Ignition on:
With the Smart Key inside the vehicle, press the
• START/STOP button to switch on ignition.
A second press will switch off the ignition.
•
Engine startThe selector lever must be in
• Park or Neutral position
to enable engine starting.
With the foot brake depressed, press and release the
• START/STOP button to start the engine.Press again to stop the engine and switch off the
• ignition.
Rolling start
If the engine is switched off while the vehicle is moving, it
can be restarted by selecting N position then pressing the
START/STOP button.
Gearshift interlock The brake pedal must
be depressed before the
selector can be moved
from the Park position.
Maintain brake pressure
until a gear is selected.
Select P before switching
off the engine. However,
if the engine is switched
off with Reverse, Drive
or Sport selected, the
selector will automatically
return to P while
retracting.
Automatic gear selection
Select D for fully automatic gear changes.
Sport mode
This is an automatic gear change mode, however,
change points are modified to make full use of
engine power.
Press the selector down and rotate from D to Sport.
Manual gear changes
Manual gear change mode is effective when rapid
acceleration and engine braking are required.
To shift down, briefly pull the left-side paddle.
•
To shift up, briefly pull the right-side paddle.•
P R N D S
STARTENGINESTOP
DSC
5432
1
6
8
7
9
When the paddles are used in D, gear selection
will revert to automatic if use of the paddles is not
maintained. With S selected, continuous manual
operation is initiated if the paddles are used.
Note: To return to automatic operation pull and hold
the right-side paddle for 2 seconds.
JJM189640131.indd 4-501/08/2012 13:45:07