child lock JAGUAR XJ 2004 X350 / 3.G Owners Manual

2 - 4 Security and Locks
Vehicle Security
When the vehicle is unoccupied or
unattended, you are advised to do the
following:
• Apply the electronic parkbrake and move the gear selector to the
Park ‘P’ position.
• Do not leave children or pets in the vehicle unattended.
• Do not leave luggage or valuables on display.
• Remove all keys, including remote transmitters, from the vehicle prior to
locking the doors, even when the
vehicle is in your garage.
• Close all windows, hood, luggage compartment and glove
compartment, and lock all the doors.
• Park the vehicle where it can be seen. At night, park in a well-lit area.
• It is important to keep your keys in safe places at all times. Leaving them
in conspicuous places is an invitation
for a thief to steal them and,
consequently, your vehicle or
belongings. Keep them as secure as
you would your wallet or purse, both
at home and away.
Key Transmitter
The security system is controlled
remotely by a radio frequency, battery-
operated, integrated transmitter key.
The transmitter is ac tivated by pressing
one of the operating buttons.
( A ) – Unlocks and disarms the vehicle.
( B ) – Releases the luggage compartment
lock.
( C ) – Activates the convenience headlamp
feature and sounds the panic alarm.
For further information on the
convenience headlamp feature,
see Headlight convenience on
page 4 - 24.
( D ) – Locks and arms the vehicle.
( E ) – Locks/unlocks the key.
To free the key, press the release
button ( E). When not required press and
hold the button and fold the key into the
transmitter housing.

2 - 14 Security and Locks
Child Safety Locks
Child safety locks are fitted to the rear
doors.
Open a rear door, insert the ignition key
into the lock and turn the key outwards.
This immobilises that door interior
handle. Repeat this for the opposite rear
door.
After setting the child lock the door(s) can
only be opened using the exterior door
handle.
To remove the child lock feature, open
the door and using a key, move the
control to its original unlock position.
Valet Key Locking
Before locking the vehicle and handing
the green-headed valet key to a parking
attendant, press the valet switch to
prevent the luggage co mpartment interior
release switch, external luggage
compartment switch, and the glove
compartment switch from being used.
When the valet switch is pressed an
audible chime will be emitted.
If the key is in ignition position ‘II’ when
the valet mode switch is pressed the
message ‘VALET MODE’ will be displayed
on the message centre. The vehicle can
then be parked by an attendant who can
lock the vehicle after parking, but cannot
open the luggage or glove compartments. The luggage compartment can then only
be unlocked with th
e key transmitter.
To cancel valet mode, press the key
transmitter unlock button or manually
unlock the luggage compartment with the
key transmitter us ing the luggage
compartment release lock.
When in valet mode each operation of
the interior luggage compartment release
switch, exterior lu ggage compartment
switch or the glove compartment switch,
will result in a chim e being emitted which
indicates that vale t mode has been
selected. If the ignition is set to
position ‘II’ a message will appear on the
message centre display indicating that an
unauthorised attempt has been made to
open the glove compartment or luggage
compartment.
Note:
1. Do not use the green-headed key for normal driving as the luggage
compartment and glove compartment
cannot be opened.

Security and Locks 2 - 19
Luggage Compartment Emergency Release
Your vehicle is equipped with a mechanical interior luggage
compartment release handle that provides a means of escape
for children and adults in the event they become locked inside
the luggage compartment.
Adults are advised to familiaris e themselves with the operation
and location of the release handle.
To open the luggage compartment lid from the inside, pull the
illuminated ‘T’ shaped handle and push up the trunk lid.
The material that the handle is made of will glow for hours in
the darkness of the luggage compartment following brief
exposure to ambient light.
!WARNING:
1. Keep vehicle doors and the luggage compartment locked and keep keys out of a child’s reach.
Unsupervised children could lock themselves in an
open trunk and risk injury. Children should be taught
not to play in vehicles.
2. On hot days, the temperature in the luggage compartment and vehicle interior can rise very
quickly. Exposure of people or animals to these high
temperatures for even a short time can cause death or
serious heat-related injuries, including brain damage.
Small children are particularly at risk.

Before Driving
Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3
Steering Column Adjustment . . . . . . . . . . . . . . . 3 - 7
Door Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 8
Interior Rear View Mirror . . . . . . . . . . . . . . . . . . 3 - 9
Occupant Protection . . . . . . . . . . . . . . . . . . . . 3 - 11
Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 11
Air Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 14
Child Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 23
LATCH Child Restraint System . . . . . . . . . . . . . 3 - 27
Memory Setting . . . . . . . . . . . . . . . . . . . . . . . . 3 - 31
Clock Adjustment . . . . . . . . . . . . . . . . . . . . . . . 3 - 32
Luggage Compartment . . . . . . . . . . . . . . . . . . . 3 - 33
Ski Hatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 34

Before Driving 3 - 11
Occupant Protection
Seat Belts
The use of front and rear seat belts is
mandatory in most countries. Using seat
belts saves lives. They should be worn by
all occupants whenever the vehicle is in
use, for maximum protection.
Lap/shoulder inertia reel seat belts are
provided for both front occupants and
three rear seat positions.
The inertia operating mechanism of the
seat belts allows the wearers to move
their upper bodies to reach various
controls. The seat belts lock automatically
with accelerated body movement or in
the event of emergency braking.
The seat belt assemblies incorporate
additional safety devices. All have belt
pretensioners and the front belts also
have force limiters. These devices provide
increased protection in the event of a
severe frontal impact.
The pretensioners operate with the air
bags as part of the Advanced Restraints
Technology System (see page 3 - 14). All passenger seat belt mechanisms
incorporate an automatic locking device
to allow child seats to be secured safely.
Forchild safety seepage3-23.
Comfort belts are fitted to both individual
electrically operated rear seats. They are
also fitted to the outer seats only on the
electrically operated rear bench seat.
These belts incorporate a twin tension
facility. When the belt is buckled around
the occupant, a reduced tension is
applied to provide a more comfortable
fitting. When the belt is unfastened,
a higher tension is applied to allow it to
retract correctly.
Beltminder
The Beltminder feature is a supplemental
warning to the seat belt warning function
(see page 4 - 6). This feature provides
additional reminders to the driver that
the driver’s and/or front passenger’s seat
belt is unbuckled by intermittently
sounding a chime and illuminating the
seat belt warning lamp in the instrument
cluster.
Note:
Not all countries have the warning
chime. Front belt height adjustment
To adjust the front seat belt heights, press
the locking button and slide the
anchorage so that the seat belt webbing
passes over the shoulder without pulling
against the neck. Release the button and
check that the anchorage point is locked.
Always check the anchorage point after
the seat has been adjusted to ensure that
the belt is correctly positioned.

Before Driving 3 - 13
Inertia reel mechanism check
Static test: Whilst seated, fasten the seat
belt and grip the shoulder belt at
approximately shoulder level with the
opposite hand. Pull the belt sharply
downwards, the belt should lock.
Road test: The following road test must
be carried out only under maximum safe
road conditions.
With the seat belt correctly fitted to the
driver and passenger(s), drive the vehicle
at 5 mph (8 km/h) and, ensuring that it is
safe to do so, brake sharply.
The seat belt(s) should lock automatically,
holding both driver and passenger(s)
securely in position.
It is important when braking that the
reactions of both driver and passenger(s)
are normal, that is, the body must not be
thrown forward in anticipation, thus
causing a snatching action of the belt
which would operate the locking
mechanism.
If the belt fails to lock on either test,
consult a Jaguar Retailer.
!WARNING:
1. Seat belts are designed to bear upon the bony structure of the
body. The lap section of the belt
must be worn low across the front
of the pelvis and NOT across the
abdominal area. Always ensure
that the webbing is midway
between the neck and the edge of
the shoulder.
2. Care should be taken to avoid contamination of the webbing
with polishes, oils and chemicals,
and particularly battery acid.
Cleaning may safely be carried out
using mild soap and water.
If webbing becomes frayed,
contaminated or damaged,
discard it and fit a new seat belt.
3. It is essential to renew the entire assembly after it has been worn in
a severe impact even if damage to
the assembly is not obvious. 4. Belts should not be worn with the
webbing twisted.
5. Each seat belt assembly must only be used by one occupant; it is
dangerous to put a seat belt
around a child being carried on
the occupant’s lap.
6. No modifications or additions s h o u l d b e m a d e b y t h e u s e r w h i c h
will prevent the seat belt adjusting
devices from operating.
7. Should the seat belt not retract and remain at its static length,
consult your nearest Jaguar
Retailer immediately.

Before Driving 3 - 25
Securing child restraints with an
adult seat belt
All passenger seat belts (not the driver’s)
have an automatic locking device for use
with child seats.
If engaged, this device allows the belt to
be retracted (tightened) but not pulled
out. When used to secure a child seat,
therefore, the belt will automatically lock
at any point to which it has retracted.
Always ensure that child restraint
assemblies are fitted in strict accordance
with the child restraint manufacturer’s
instructions. Keep the fitting instructions
for future reference.
The following checks should always be
carried out:
• Fit the child seat in the correct position and secure with the seat belt
in accordance with the
manufacturer’s instructions.
If necessary, remove the headrest to
accommodate a larger child seat.
• Pull the seat belt all the way out to engage the locking device.
• Make sure the child seat is fitted firmly to the car seat. There should
not be excessive forward or sideways
movement. • To fix the seat firm
ly, retract the belt
back onto the reel; a ratchet
operation may be felt as the belt
retracts. Continue to pay the belt back
onto the reel until it fits snugly around
the child seat.
• Regularly check and refit the child seat to ensure there is no slack in the
installation.
• The seat belt must not be twisted and
the buckle must not rest on the child
seat frame, as it may snap open in an
accident.
• Never modify the seat, or install it differently to the instructions.
The above is a guide only. Depending on
the features of a particular child seat,
e.g. forward or rearwa rd-facing, engage
the locking device before or after
attaching the belt, as convenient.
Unbuckling the belt and releasing the
child seat will allow th e belt to resume its
normal operation.
Always secure an unoccupied child seat
safely. In an accident an unsecured child
seat may pose a risk to the vehicle
occupants. Safe use of child restraints
!WARNING:
The top tether anchor point must
always be used to secure forward-
facing child seats (see page 3 - 29).
Ensure that there is no slack in the
webbing and that the restraints fits the
child snugly across the rib cage and hips.
These are the parts of the body most able
to take the force of an impact.
• Ensure the path and position of an integral harness across the shoulders
is appropriate for your child’s
development – consult the
manufacturer’s instructions.
• The lap strap should pass across the top of the child’s thighs, bearing on
the pelvis, not the abdominal area.
• Adjust the harness every time so that one or two fingers only can be
inserted between the child and the
harness. Different clothing on a child
can make a difference to the correct
fitting of the harness.
• Make sure that the webbing is not twisted.

3 - 26 Before Driving
• Never modify the seat harness or buckles as this may affect the quick
release mechanism.
• Always secure your child correctly, even for a short journey.
• Follow the manufacturer’s instructions for harness adjustments.
Booster seats
If a booster seat is used, position the lap
section of the adult seat belt over the
child’s pelvis. The diagonal seat belt
should rest on the child’s shoulder,
not the neck.Check List – Non-LATCH Child
Restraints
Follow the check list each time a child
travels in the vehicle:
• Always attach the top tether when
installing a forward-facing child seat.
• Carefully follow the instructions provided by the manufacturer of the
restraint system.
• Always use the appropriate child restraints and adjust harnesses for
every child, every trip.
• Avoid dressing a child in bulky clothing and do not place any objects
between the child and the restraint
system.
• No child seat is completely child- proof. Encourage your child not to
play with buckle or harness. • Regularly check the fit of your child
seat and replace seats or harnesses
that show signs of wear.
• Ensure that you have removed all slack from the adult seat belt and that
the automatic locking device is
activated.
• Never leave a child unsupervised in the vehicle.
• Activate the rear door child safety locks (see page 2 - 14).
• Ensure your child does not exit the vehicle from the side where there is
traffic.
• Set your child a good example – always wear your seat belt.

3 - 28 Before Driving
Fitting LATCH seats
For further information regarding a LATCH child seat, please
consult your Jaguar Retailer.
Always use the additional top tether anchorage.
LATCH child seats can only be fi tted to the two outer rear seat
positions, as shown on the previous page.
Caution: When fitting a LATCH child seat, the seat
manufacturers instructions must always be followed.
The following is a guide only.
Note: So as not to interfere with the fitment of large child seats,
push the adult seat buckles into their buckle recesses and,
if necessary, remove the headrest.
LATCH seat with extendable bars (A) – Fit the seat as
follows:
1. Expose the LATCH loops between the seat and seat back.
2. Make sure that the adult seat belts and buckles do not become trapped behind the child seat.
3. Make sure there is nothing obstructing the seat mounting mechanism at the anchorage points.
4. Make sure you do NOT trap the top tether strap behind the child seat.
5. Fully extend the two attachme nt bars on the child seat
(see manufacturer’s instructions).
6. Locate the slots on the ends of the bars onto the two LATCH
loops, then push the seat asse mbly rearwards until the bars
are positively engaged (a trigger operates to lock the
attachment bars onto the loops). 7. Slide the seat rearwards along the legs until it is locked firmly
against the vehicle seat back. Confirm that it is securely
locked in position.
8. Secure a forward-facing ch ild seat to the top tether
anchorage.
LATCH seat with tether straps (B) – Clip the flexible lower
straps to the two LATCH loops. Adjust the length of each strap
until the seat is held firmly against the vehicle seat back.
!WARNING:
Do not install a LATCH child seat with flexible lower
attachments in the vehicle centre seat position.
The anchorage loops are only provided to install a
compatible child seat in the vehicle outboard seat
positions.

3 - 30 Before Driving
Check List – LATCH Child
Restraints
Follow the check list each time your child
travels in the vehicle:
• Always attach the top tether when installing a forward-facing seat.
• Carefully follow the instructions supplied with the child seat.
• Always give the seat a final pull to ensure the lower anchors are secure,
even if the seat has indicators to show
that the seat connectors are latched.
• Always use the appropriate child restraints and adjust harnesses for
every child, every trip.
• Make sure you use a seat with the correct weight range for your child. • Avoid dressing your child in bulky
clothing and do not place any objects
between the child and the restraint
system.
• Regularly check the fit of your child seat and replace seats or harnesses
that show signs of wear.
• No child seat is completely child- proof. Encourage your child not to
play with the buckle or harness.
• Never leave a child unsupervised in the vehicle.
• Activate the rear door child safety locks (see page 2 - 14).
• Ensure your child does not exit the vehicle from the side where there is
traffic.
• Set your child a good example – always wear your seat belt.