oil type JAGUAR XJ 2004 X350 / 3.G Owners Manual
[x] Cancel search | Manufacturer: JAGUAR, Model Year: 2004, Model line: XJ, Model: JAGUAR XJ 2004 X350 / 3.GPages: 227, PDF Size: 4.22 MB
Page 21 of 227
2 - 6 Security and Locks
Key transmitter battery renewal
When the battery needs renewal there will be a significant
decrease in the effective range of the key transmitter. To renew
the battery, follow the procedure below:
• Insert a small, flat-blade, screwdriver at an angle of about 45 degrees, into the slot on th e back of the key transmitter
as shown ( A). Apply light pressure to the screwdriver and
lever the screwdriver forward to separate the two halves of
the key transmitter. Finally, pu ll the transmitter from the key
body.
• Insert the screwdriver into th e slot between the transmitter
covers adjacent to the key stowage area as shown ( B).
Apply light pressure to the screwdriver and lever the
screwdriver downward to separate the covers.
• Unscrew and remove the small screw ( C) and remove the
printed circuit board, taking care not to touch the battery
terminals. Remove the battery and dispose of it safely.
• Fit a new battery cell, type CR2032 (available from your
Jaguar Retailer), with the si de marked with the positive
symbol (+) downwards in the battery receptacle.
Avoid touching the new battery as moisture/oil from the
fingers can reduce the life of the battery and corrode the
contacts.
• Replace the printed circuit board making sure to engage the board under the securing tabs (D ), and secure with the
screw.
• Refit the cover and click into place with thumb pressure.
• Slide the transmitter back onto the key body until it clicks
into place.
Page 134 of 227
On the Road 4 - 63
Fuel and Refuelling
Before refuelling, switch off the ignition
and remove the key.
Note:Do not leave the ignition key in the
vehicle; vehicles have been stolen from
garage service/filling stations whilst the
driver is absent from the vehicle. It is
recommended that the vehicle is locked,
if left unattended.
Caution: No additives of any kind
(fuel or oil) must be put into the fuel
tank. Additives could reduce engine
life or affect exhaust emissions.
!WARNING:
1. Fuel vapour is highly flammable and in confined spaces is
explosive and toxic. In the event
of inadvertent spillage, and before
refuelling, always switch OFF the
engine. Do not use exposed flame
or light. Do not smoke. Do not
inhale fumes.
2. Do not fill the tank so that fuel is visible in the fuel filler intake
tube. This could cause spillage
and danger from exposed fuel.
Fuel Tank Filling
Caution: Your vehicle is fitted with
catalytic converters and must only be
filled with ‘Unleaded Fuel’.
The fuel filler flap release switch is
located in the knee bolster switchpack
below the fascia. The fi ller flap is on the
right-hand side of the vehicle.
A small arrow is shown on the fuel gauge
as a reminder on which side of the
vehicle the fuel filler flap is located. Open the fuel filler flap and turn the filler
cap anti-clockwise, a ¼ turn until
resistance is felt. Continue turning to
release the cap from the filler neck.
The cap is held by a retaining strap and
can be stowed over the hook on the flap
to allow easy access to fill the tank.
A warning label on the inside of the fuel
filler flap advises type/grade of fuel.
Page 166 of 227
Roadside Emergency 6 - 15
Dipped beam (outer) headlights
Caution: Halogen bulbs will be
damaged if touched by hand or
contaminated with oil or grease. It is
important to use clean gloves or cloth
when handling a bulb which is to be
used again. A contaminated bulb may
be cleaned with methylated spirit
before refitting.
Open the hood and remove the top cover
as shown on page 6 - 14.
Pull the retaining clip (arrowed in A
above) upwards. Move the top of
headlight assembly outer bulb cover
rearwards to gain a ccess to the bulbs. Pull off the bulb connector. Release the
bulb spring clip (
B) from below the bulb
and lift it clear of the bulb. Pull out the
bulb from the headlight assembly.
Locate the new bulb (type H7) into the
headlight with the bulb tab
uppermost ( C). The bulb will only fit
correctly in one position.
Engage the spring clip ( B) to secure the
bulb. Fit the bulb connector.
Refit the bulb cover to the headlight
assembly and secure with the retaining
clip.
Refit the top cover and close the hood.
It is advisable to have the headlight aim
checked by a Retailer after bulb renewal. Front direction indicator bulb
The front direction indicator bulb is
located above the outer headlight bulb
(halogen or HID type) and is accessed via
the outer bulb cove
r (see column 1).
Turn the bulb holder a quarter turn anti-
clockwise and pull out ( D).
Remove the bulb and fit a new one of the
correct type, PY21W.
Fit the bulb holder to the lamp unit,
it will only fit in one position.
Turn clockwise to secure. Refit the
headlight assembly ou ter bulb cover and
secure with the retaining clip.
Refit the top cover and close the hood.
Page 167 of 227
6 - 16 Roadside Emergency
Main beam (inner) headlight
Caution: Halogen bulbs will be
damaged if touched by hand or
contaminated with oil or grease. It is
important to use clean gloves or cloth
when handling a bulb which is to be
used again. A contaminated bulb may
be cleaned with methylated spirit
before refitting.
Open the hood and remove the top cover
as shown on page 6 - 14.
On the headlight assembly, turn the rear
inner cover (A) anti-clockwise as shown
and remove. Pull off the bulb co
nnector. Release the
bulb spring clip ( B) from below the bulb
and lift it clear of the bulb. Pull out the
bulb from the headlight assembly.
Locate the new bulb (type H7) into the
headlight with the bulb tab
uppermost ( C). The bulb will only fit
correctly in one position.
Engage the spring clip ( B) to secure the
bulb. Fit the bulb connector.
Fit the rear cover and turn it clockwise to
secure.
Refit the top cover and close the hood. Front parking (side) light – bulb
renewal
Open the hood and remove the top cover
as shown on page 6 - 14.
On the headlight asse
mbly, turn the rear
inner cover ( A) anti-clockwise as shown
and remove.
Turn the bulb holder ( D) anti-clockwise
to remove it from the headlight assembly.
Remove the bulb from the holder and fit a
new one of the correct type, W5W.
Reposition the bulb holder in the
headlight unit and turn it clockwise.
Fit the rear cover and turn it clockwise to
secure.
Refit the top cover and close the hood.
Page 175 of 227
6 - 24 Roadside Emergency
Engine compartment fuse boxFuse No Fuse
Type Rating
(amps) Colour
Circuit
F1 ATO 10A Red Front ignition, UHEGO, fu el pump, rear ignition relay coils
F2 – F3 Not used
F4 ATO 30A Green Powerwash pump
F5 Not used
F6 ATO 40A Orange Air suspension compressor
F7 ATO 40A Orange Right-hand front screen heater or wiper park zone heater
F8 ATO 20A Yellow Right-hand dipped beam
F9 ATO 20A Yellow Left-hand dipped beam
F10, F11 Not used
F12 ATO 10A Red Engine control module
F13 ATO 10A Red Fuel injectors
F14 ATO 10A Red Purge valve, EGR valve, canister close valve (CCV), port deactivation, V6 intake manifold
tuning valves (IMTV), MAFS, air filter solenoid, radiator fan controller
F15 Not used
F16 ATO 20A Yellow Right-hand main beam, left-hand main beam
F17 ATO 10A Red Engine control module, transmission control module
F18 ATO 15A Blue Front fog lights, instrument cluster front fog status
Page 176 of 227
Roadside Emergency 6 - 25
F19 ATO 25A Natural Starter solenoid
F20 ATO 30A Green ABS module (pump)
F21 Not used
F22 ATO 30A Green ABS module
F23 Not used
F24 ATO 20A Yellow Throttle motor
F25 ATO 15A Blue Horns
F26 ATO 40A Orange Wiper system, front electronics module (FEM)
F27 – F29 Not used F30 ATO 10A Red Ignition coils
F31 ATO 15A Blue Intercooler water pump (supercharged engines)
F32 ATO 40A Orange Left-hand front screen heater
F33 ATO 30A Green ‘A’ bank heated oxygen sensors
F34 ATO 30A Green ‘B’ bank heated oxygen sensors
F35 Midi 80A Radiator cooling fan
Fuse No
Fuse
Type Rating
(amps) Colour Circuit
Page 177 of 227
6 - 26 Roadside Emergency
Cabin fuse boxFuse No Fuse
Type Rating
(amps) Colour
Circuit
F1 ATO 10A Red Climate control unit, fan, screen heaters and wiper relay coils, smog sensor
F2 ATO 5A Tan Radiator fan controller, cruise control switch, adaptive cruise control
F3 ATO 5A Tan Rear outer seat, electrochromic mirror, driver seat heater, electric parkbrake, left and right-hand HID lamps levelling, left and right-hand seat belt switches
F4 ATO 5A Tan Instrument cluster
F5 – F6 Not used
F7 ATO 5A Tan Cigar lighter, sunroof module, electric park brake switch illumination, accessory relays (trunk fuse box)
F8 ATO 5A Tan Instrument cluster
F9 ATO 10A Red Left-hand direction indicator and repeater
F10 ATO 5A Tan Glove compartm ent door motor and lamps
F11 ATO 5A Tan Radio muting (engine start), ignition feed
F12 ATO 10A Red Front electronic module (FEM), passenger mirror
F13 ATO 20A Yellow Rear electronic module (REM), door locks
F14 ATO 10A Red Courtesy light, footwell lamps, rain sensor, FEM
F15 ATO 5A Tan ECM, FEM, instrument cluster air bag fa ult lamp, instrument cluster ignition (run/start)
F16 ATO 5A Tan Diagnostic connector
Page 189 of 227
7 - 6 Maintenance
Checking and Top Up
Check Engine Oil Level
Check the oil level regularly with the vehicle on flat, level
ground.
Refer to page 7 - 5 for dipstick and oil filler locations.
It is preferable to check the oil level after the vehicle has been
standing, that is, with th e engine completely cold.
If the engine has been started do not check the oil level until the
engine has reached normal operating temperature. Stop the
engine and wait for a minimum of 5 minutes to allow the oil to
drain back into the sump.
Remove the dipstick ( A) and wipe clean with a non-fluffy cloth.
Replace fully, then wi thdraw the dipstick. If the oil level is above
the lower of the two dots on the dipstick then no additional oil
is required.
If the oil level reaches the lower of the two dots, remove the oil
filler cap ( B) and add oil, to the quantity and specification
shown on the next page.
Refit the filler cap and hand tighten securely.
Caution: Do not use oil additives of any type. Use only
specified lubricants.