battery JEEP CHEROKEE 1988 Service User Guide

proper increased enrichment for the next engine start. Idle speed is
nonadjustable.
EMISSION CONTROL
The ECU electrically controls Exhaust Gas Recirculation (EGR).\
An ECU-controlled solenoid valve is used to control EGR valve
function. This valve is located on the left inner fender panel and is
operated by the ECU in response to coolant temperature, throttle
position, and manifold pressure.
Under conditions of engine warm-up, engine idle, wide open
throttle, or rapid acceleration/deceleration, the solenoid valve is
energized, blocking vacuum to the EGR valve. At normal operating
temperatures with engine speed above idle, the solenoid valve is de-
energized, allowing normal EGR valve function.
NOTE: If the electrical connector is removed from the EGR solenoid,
EGR flow will be allowed at all times.
A/C CLUTCH CONTROL
The ECU controls the A/C compressor clutch to improve idle
quality. The A/C compressor clutch will be engaged or disengaged as
deemed necessary by the ECU through the A/C clutch relay.
SHIFT LIGHT CONTROL
The shift light system is used on all manual transmission
equipped vehicles. The ECU monitors coolant temperature, throttle
position, vehicle speed, and engine speed to control the shift light.
The ECU calculates what gear position the vehicle should be in and
uses this information to turn on the light. The light indicates the
best shift point to the driver for maximum fuel economy.
The light is tested when the ignition switch is turned on.
When the engine is started, the light should go out. A transmission-
mounted switch prevents the light from illuminating when the
transmission is shifted into high gear. The ECU turns the light off if
the shift to the next higher gear is not performed within 3-5 seconds
after light comes on.
DIAGNOSIS & TESTING
PRELIMINARY CHECKS
Before assuming that the ECU is faulty, the following systems
and components must be in good condition and operating properly:
* Air filter.
* All support systems and wiring.
* Battery connections and specific gravity.
* Compression pressure.
* Electrical and vacuum connections to components, sensors and
switches.
* Emission control devices.
* Ignition system.
* All vacuum and fuel line (hose) connections.
FUEL SYSTEM TEST
Fuel Pressure
1) Remove cap from pressure test port on fuel rail and

If no continuity is shown, repair wiring harness. If
continuity is shown, reconnect voltmeter as in step 2).
5) While observing voltmeter, crank engine. Voltmeter needle
should fluctuate back and forth during engine cranking. This verifies
proper operation of distributor stator. If voltmeter needle does not
fluctuate, replace stator.
EGR Solenoid Valve
1) Make sure vacuum is present at port "C" of the solenoid.
See Fig. 6 . Remove vacuum connector from ports "A" and "B" of
solenoid. Connect vacuum gauge to port "B". Start engine and run at
idle. Vacuum should not be present at port "B".
2) Disconnect electrical connector from solenoid. Vacuum
should now be present at port "B". Stop engine. Reconnect electrical
connector at solenoid. Remove vacuum gauge and reconnect vacuum hoses.
Relays - General Testing
1) The relays used on the 4.0L engine are all of the same
basic construction and design. Terminal No. 30 is usually connected to
battery voltage ("switched" or battery positive at all times).
Terminal No. 87A is connected to terminal No. 30 in de-energized
position.
2) Terminal No. 87 is connected to terminal No. 30 in the
energized position. This connection supplies battery voltage to the
operated device.
3) Terminal No. 86 is connected to the electromagnet of the
operated device; usually through a "switched" power source. Terminal
No. 85 is connected to the electromagnet of the operated device;
usually grounded through a switch or the ECU.
NOTE: Not all relays have battery voltage applied at terminal No.
30. Some may have battery voltage applied at terminal Nos. 87
or 87A. Check design of relay before testing.
4) When testing relays, there should be continuity between
terminal Nos. 87A and 30 when relay is in de-energized position.
Resistance between terminal Nos. 85 and 86 should be 70-80 ohms for
resistor-type relays and 81-91 ohms for diode-type relays.
Fig. 6: Testing EGR Solenoid Valve
Starter Motor Relay
1) Disconnect electrical connectors from terminals "I" and
"G". Using an ohmmeter, measure resistance between the terminals.

Resistance value should be about 22 ohms. Measure resistance between
either terminal and battery negative post. Resistance value should be
infinite. If resistance values are not as specified, replace relay. If
okay, reconnect electrical connectors.
2) Disconnect electrical connector from "SOL" terminal.
Connect voltmeter between terminal and battery negative post. While
observing voltmeter, turn ignition switch to "START" position. If 12
volts is not indicated, check and repair wiring harness, bulkhead
connector, and/or ignition switch. If battery voltage is present, go
to next step.
3) If battery voltage is present, but starter relay does not
work, place transmission in Park (Neutral for man. trans.) and apply
parking brake. Disconnect electrical connector from terminal "I" (Dark
Green wire) and apply battery voltage to terminal. Using a jumper
wire, touch terminal "G" to ground. If relay does not click, replace
relay. If relay does click, repair ground circuit.
Fig. 7: Design & Function of Relays
REMOVAL & INSTALLATION









\









\








\









\









\









\









\






 
ABBREVIATION DEFINITION 










\








\b
\









\









\









\









\









\






B/P Backpressure 

BAC By-Pass Air Control 

BAP Barometric Absolute Pressure Sensor 

BARO Barometric 

BBDC Before Bottom Dead Center 

BCM Body Control Module 

BDC Bottom Dead Center 

BHP Brake Horsepower 

BLK Black 

BLU Blue 

BMAP Barometric & Manifold Absolute Pressure Sensor 

BOO Brake On-Off Switch 

BP Barometric Pressure sensor 

BPS Barometric Pressure Sensor 

BPT Backpressure Transducer 

BRN Brown 

BTDC Before Top Dead Center 

BTU British Thermal Unit 

BVSV Bimetallic Vacuum Switching Valve 

Baro. Barometric 

Batt. Battery 

Bbl. Barrel (Example: 4-Bbl.) 

Blst. Ballast 

Blwr. Blower 

Brkr. Breaker 











\








\









\









\









\









\









\





\f

"C" ABBREVIATION TABLE
"C" ABBREVIATION TABLE







\









\








\









\









\









\









\








ABBREVIATION DEFINITION 










\








\b
\









\









\









\









\









\






C Celsius (Degrees) 

C(3) I Computer Controlled Coil Ignition 

C(4) Computer Controlled Catalytic Converter 

CANP Canister Purge solenoid 

CARB California Air Resources Board 

CAT Catalytic Converter 

CB Circuit Breaker 

CBD Closed Bowl Distributor 

CBVV Carburetor Bowl Vent Valve 

cc Cubic Centimeter 

CCC Computer Command Control 

CCD Computer Controlled Dwell 

CCM Central Control Module 

CCO Converter Clutch Override 

CCOT Cycling Clutch Orifice Tube 

CCW Counterclockwise 

CDI Capacitor Discharge Ignition 

CEC Computerized Engine Control 

CFI Central Fuel Injection 

CID Cubic Inch Displacement 

CID Cylinder Identification sensor 

CIS Continuous Injection System 

CIS-E Continuous Injection System-Electronic 

CKT Circuit 

CLR Clear 

CNG Compressed Natural Gas 

TCC Torque Converter Clutch 

TCCS Toyota Computer Control System 

TDC Top Dead Center 

TDCL Total Diagnostic Communication Link 

TFI Thick Film Ignition system 

TGS Top Gear Switch (cancels SIL in top gear) 

THERMAC Thermostatic Air Cleaner 

THS Transmission Hydraulic Switch 

TP/TPS Throttle Position Sensor 

TPI Tuned Port Injection 

TPS Throttle Position Sensor/Switch 

TS Temperature Sensor 

TSB Technical Service Bulletin 

TTS Transmission Temperature Switch 

TV Thermovalve 

TWC Three-Way Catalyst 

Temp. Temperature 

Trans. Transaxle/Transmission 











\








\









\









\









\









\









\





\f

"V" ABBREVIATION TABLE
"V" ABBREVIATION TABLE







\









\








\









\









\









\









\






 
ABBREVIATION DEFINITION 










\








\b
\









\









\









\









\









\






V Valve 

VAF Vane Air Flow sensor or circuit 

VAPS Variable Assist Power Steering 

VAT Vane Air Temperature 

VATS Vehicle Anti-Theft System 

VBATT Vehicle Battery Voltage 

VCC Viscous Converter Clutch 

VIN Vehicle Identification Number 

VIO Violet 

VLR Volt Loop Reserve 

VM Vacuum Modulator 

VM Vane Meter 

VOM Volt-Ohmmeter (Analog) 

VPWR Vehicle Power supply voltage (10-14 volts) 

VREF Voltage Reference (ECA supplied reference voltage 

VRV Vacuum Regulator Valve 

VSC Vehicle Speed Control sensor or signal 

VSS Vehicle Speed Sensor or signal 

VSV Vacuum Switching Valve 

Vac. Vacuum 

Volt. Voltage 











\








\









\









\









\









\









\





\f

"W" ABBREVIATION TABLE
"W" ABBREVIATION TABLE







\









\








\









\









\









\









\








ABBREVIATION DEFINITION 










\








\b
\









\









\









\









\









\






W/ With 

W/O Without 

WAC WOT A/C Cut-off switch or circuit 

WAC Wide Open Throttle A/C Switch 

WHT White 

WOT Wide Open Throttle 

YEL Yellow 

Discharge system (slowly to prevent loss of compressor oil)
using approved refrigerant recovery/recycling equipment. Disconnect
evaporator and condenser lines from receiver-drier. Detach mounting
screws from receiver-drier bracket. Remove receiver-drier.
Installation
To install, reverse removal procedure. Evacuate, leak test,
recharge. Check A/C system for proper operation.
Fig. 1: Exploded View of Wrangler Evaporator Housing
Courtesy of Chrysler Motors.
EVAPORATOR-BLOWER HOUSING &
HEATER & EVAPORATOR CORES
NOTE: The following procedures are for vehicles with A/C-heater
systems only. For replacement of heater cores on vehicles
with heater systems only, see HEATER SYSTEMS, JEEP article.
Removal (Cherokee, Comanche & Wagoneer)
1) Disconnect battery ground. Discharge A/C system using
approved refrigerant recovery/recycling equipment. Disconnect A/C
hoses from expansion valve. Drain cooling system. Disconnect heater
hoses at core tubes. Disconnect blower motor wires and vent tube.
2) Remove console (if equipped). Remove lower instrument
panel. Disconnect electrical connectors at A/C relay, blower motor
resistors and A/C thermostat. Disconnect vacuum hose at vacuum motor.
Cut plastic retaining strap holding evaporator-blower housing to
heater core housing.
3) Disconnect blend-air heater control cable. Detach clip at
rear of blower housing flange and remove retaining screws. Remove

panel to gain access to blower motor mounting screws.
2) Remove screws attaching evaporator housing to instrument
panel and mounting bracket. Lower evaporator housing and pull hoses
and grommet through opening.
Installation
To install, reverse removal procedure. Evacuate, leak test,
recharge and check A/C system for proper operation.
EXPANSION VALVE
Removal (Cherokee, Comanche & Wagoneer)
Discharge A/C system using approved refrigerant
recovery/recycling equipment. Disconnect A/C hoses from expansion
valve. Disconnect expansion valve from evaporator core inlet and
outlet tubes. Remove expansion valve.
Installation
To install, reverse removal procedure. Evacuate, leak test,
recharge and check A/C system operation.
NOTE: The expansion valve is pre-set and should not be adjusted. A
faulty valve requires replacement.
Removal (Wrangler)
1) Discharge system using approved refrigerant
recovery/recycling equipment. Remove evaporator housing. Remove
insulation wrapped around suction line and expansion valve.
2) Mark capillary tube location on suction line. Disconnect
inlet and outlet connections, capillary tube clamp and equalizer tube.
Remove expansion valve.
Installation
1) Clean suction line to provide positive contact with
replacement expansion valve capillary tube. Connect inlet and outlet
hoses. Clamp capillary tube securely at marked position and connect
equalizer tube.
2) Wrap expansion valve and line with insulation. Install
evaporator housing assembly. Evacuate, leak test, recharge and check
A/C system operation.
TEMPERATURE CONTROL THERMOSTAT
Removal (Cherokee, Comanche & Wagoneer)
1) Disconnect battery ground. Remove console (if equipped).
Remove lower instrument panel. Disconnect electrical connection at
thermostat. See Fig. 3.
2) Remove capillary tube retaining screw. Remove thermostat
retaining screws. Remove capillary tube from tube guide hole.
Installation
1) To install, feed capillary tube through tube guide hole
until Red tape on capillary tube just enters hole in housing. Install
capillary tube retaining screw and clip.
2) Install thermostat retaining screws and attach electrical
connection. To complete installation, reverse removal procedure.
CAUTION: Handle capillary tube with care to avoid bends or kinks
which could cause thermostat to malfunction.
Removal (Wrangler)
Remove evaporator housing assembly. Remove lower cover.

be obtained. During high speeds "on" time may be 10 percent and "off"
time 90 percent. During low speeds with high electrical loads, "on"
time may be 90 percent and "off" time 10 percent.
SI SERIES
A rectifier bridge, connected to stator windings, contains 6
diodes (3 positive and 3 negative) molded into an assembly. This
rectifier bridge changes stator AC voltage into DC voltage, which
appears at output terminal.
Alternator field current is supplied through a diode trio
which is also connected to stator windings. A capacitor is mounted to
end frame, protecting rectifier bridge and diodes from high voltage
and suppressing radio interference noise.
TROUBLE SHOOTING
NOTE: See the TROUBLE SHOOTING - BASIC PROCEDURES article
in the GENERAL TROUBLE SHOOTING section.
TESTING
PRELIMINARY INFORMATION
NOTE: Before making electrical checks, visually inspect all
terminals for clean, tight connections. Check alternator
mounting bolts and drive belt tension. Battery must be in
good condition to test charging system.
TESTING (ON-VEHICLE)
CS SERIES
Over/Undercharged Battery (W/ STandard Instruments)
1) If an overcharging condition is suspected, run engine at a
moderate speed. Connect a voltmeter across battery terminals. If
voltmeter indicates more than 16 volts, replace alternator.
2) If an undercharging condition is suspected, disconnect
2
wire connector from alternator. Turn ignition on with engine off.
Connect a voltmeter between terminal "L" in wiring harness and ground.
Record reading.
3) If terminal "I" is used, connect voltmeter between
terminal "I" and ground. Record reading. If voltmeter reads battery
voltage, circuits are okay. If voltmeter reads zero, this indicates an
open circuit between terminal checked and battery. Repair as
necessary.
Overcharged Battery (W/ Gauges)
If an overcharging condition is suspected, run engine at a
moderate speed. Connect a voltmeter across battery terminals. If
voltmeter indicates more than 16 volts, replace alternator.
Alternator Output Test (W/ Standard Instruments Or Gauges)
1) Run engine at moderate speed, all electrical accessories
off. Measure voltage across battery, if above 16 volts, replace
alternator.
2) Connect an ammeter in circuit at "BAT" terminal of
alternator. Turn on all available accessories. Connect a battery load
tester across battery. Operate engine at 2000 RPM and adjust battery
load tester as required to obtain maximum current output while

maintaining 13 volts or more.
3) Output must be within 15 amps of rated output stamped on
alternator. If output is not within 15 amps of rated output, replace
alternator.
SI SERIES
Overcharged Or Undercharged Battery
1) If an overcharging condition is suspected, attach a
voltmeter across battery terminals. Run engine at a moderate speed
with all accessories off. If voltmeter reads 15.5 volts or more,
remove alternator for repair.
2) If an undercharging condition is suspected, turn ignition
on. Connect a voltmeter from alternator "BAT" terminal to ground.
Voltmeter should read 12 volts. Connect voltmeter between No. 1
terminal and ground. Voltmeter should read one volt or more.
3) Connect voltmeter between No. 2 terminal and ground.
Voltmeter should read 12 volts. A zero reading on any connection
indicates an open between connection and battery. Opens in the No. 2
lead may be between terminals at the crimp between harness wire and
terminal, or in wire.
Alternator Output Test
1) Connect an ammeter in circuit at "BAT" terminal of
alternator. Turn on all available accessories. Connect a carbon pile
across battery. Operate engine at 2000 RPM and adjust carbon pile as
required to obtain maximum current output.
2) Ampere output must be within 10 amps of rated output. If
output is not within 10 amps of rated output, ground field winding by
inserting a screwdriver into test hole. Repeat step 1).
3) If output is increases to within 10 amps of rated output
with field grounded, regulator is defective. If output remains below
10 amps of rated output, check field winding, diode trio, rectifier
bridge, and stator.
CAUTION: Tab is within 3/4" of casting surface. DO NOT force tool
beyond 1" into end frame. If test hole is not accessible,
proceed to BENCH TESTING.
BENCH TESTING
NOTE: There are no internal checks for CS series alternators.
SI SERIES
Rotor Field Winding Test
1) To check for grounds, attach ohmmeter leads to shaft and
slip ring (each ring in turn). If reading is not infinity, replace
rotor.
2) To test for open field, attach ohmmeter leads to each slip
ring. Resistance should measure about 2.4
2.8 ohms on 12SI series, or
1.72.1 ohms on 17SI series. If not, replace rotor.

Brake switch is an input device mounted above the brake
pedal. When brake pedal is operated, brake switch delivers an input
signal to the TCM. The TCM uses input signal for controlling No. 3
valve body solenoid for torque converter lock-up.
NEUTRAL SAFETY SWITCH
NOTE: Neutral safety switch may be referred to as park/neutral
safety switch or gear select switch.
Neutral safety switch is an input device mounted on the
transmission manual valve shaft. Neutral safety switch delivers an
input signal to TCM, indicating transmission manual valve gear
position.
SPEED SENSOR
Speed sensor, mounted in adapter housing or extension
housing, is an input device consisting of speed sensor rotor and speed
sensor. Speed sensor rotor is mounted on transmission output shaft.
Input signal is delivered from speed sensor to TCM with each
revolution of transmission output shaft. The TCM uses input signal for
controlling transmission operation.
THROTTLE POSITION SENSOR (TPS)
The TPS, mounted on throttle body, determines throttle
position and delivers an input signal to TCM. The TCM uses input
signal for controlling transmission upshifts and torque converter
lock-up.
SELF-DIAGNOSTIC SYSTEM
DIAGNOSTIC PROCEDURE
When performing vehicle diagnosis:
* Ensure transmission fluid level is correct and fluid is
neither contaminated nor aerated.
* Ensure shift cable is properly adjusted. Refer to the
appropriate TRANSMISSION SERVICING - A/T article in
this section.
* Ensure battery is fully charged.
* Perform visual inspection, ensuring all electrical
connections at transmission, TCM, throttle position sensor,
neutral safety switch, speed sensor and brake switch are
clean and properly installed.
* Perform TEST 1A - VERIFICATION OF THE COMPLAINT under TROUBLE
SHOOTING CHARTS in this article.
* Repair diagnostic trouble codes in order displayed.
* Always perform TEST 2A - VERIFICATION TEST after repair is
completed. See TEST 2A - VERIFICATION TEST under TROUBLE
SHOOTING CHARTS in this article.
RETRIEVING DIAGNOSTIC TROUBLE CODES
NOTE: Manufacturer recommends using Chrysler's Diagnostic Readout
Box-II (DRB-II) with proper cartridge for system diagnosis.
Other after-market scan tools may be used for system
diagnosis. The following procedure is for DRB-II scan tool
usage. Use manufacturer's instruction for operating the