roof JEEP CHEROKEE 1988 Service Repair Manual

Clean hub and rotor mating surfaces. To install, reverse
removal procedure.
NOTE: DO NOT disconnect brake hose from caliper unless caliper is
to be disassembled.
DISC BRAKE ROTOR - CHEROKEE, COMANCHE & WAGONEER
Removal
1) Raise and support vehicle. Remove front wheel and caliper.
Suspend caliper from frame or suspension. Remove cap, cotter pin, nut
retainer, adjusting nut and thrust washer from spindle.
2) Remove outer bearing from hub. Remove hub and rotor from
spindle. Remove hub and rotor seal. Remove inner bearing from hub.
Installation
1) Apply small amount of "EP" type waterproof wheel bearing
grease in hub cavity. Lubricate inner and outer bearings. Install
inner bearing and seal in rotor. Clean rotor surface (if necessary).
2) Install hub and rotor on spindle. Install outer bearing,
thrust washer and spindle nut. Tighten spindle nut to 17-25 ft. lbs.
(23-34 N.m) while rotating rotor to seat bearings. Loosen spindle nut
1/2 a turn and retighten an additional 19 INCH lbs (2 N.m). Reverse
removal procedure to complete installation.
DISC BRAKE ROTOR - GRAND WAGONEER
Removal
1) Raise vehicle and support with safety stands. Remove wheel
and caliper. On models without front hubs, remove rotor hub cap, drive
gear snap ring, drive gear, pressure spring and spring cup.
2) On models with front hubs, remove screws attaching hub
body to hub clutch and remove hub body from clutch. Remove large and
small retaining rings. Remove hub clutch from axle shaft.
3) On all models, remove wheel bearing outer and inner lock
nuts and retaining ring using Socket (J-6893-D). Remove rotor. Remove
wheel bearings from rotor.
Installation
1) Lubricate bearings with "EP" type waterproof wheel bearing
grease. Install bearings and seal in rotor. Install rotor and inner
lock nut. Inner lock nut has a locating peg on one side. When
installed, peg must face away from bearing.
2) Install wheel, but do not tighten lug nuts completely.
Tighten inner lock nut to 50 ft. lbs. (68 N.m) while rotating wheel.
Back of inner lock nut 1/6 turn (45-65 degrees).
3) Install retaining washer. Ensure that inner lock nut
locating peg is engaged with retaining washer. Install outer lock nut
and tighten to 50 ft. lbs. (68 N.m).
4) On models without front hubs, install pressure spring cup,
pressure spring, drive gear and snap ring. Coat rim of chrome hub
cover with Permatex No. 3 and install cap in rotor hub.
NOTE: Recessed side of spring cup faces outer bearing and flat
side faces pressure spring.
5) On models with front hubs, install hub clutch on axle.
Install large and small hub retaining rings. Install hub body on
clutch and tighten to 30 INCH lbs. (3 N.m). Reverse removal procedure
to complete installation.
DRUM BRAKE SHOES - EXCEPT GRAND WAGONEER

2. Peel the label from its backing and apply it near the Vehicle
Emissions Control Information Label on the underside of the hood.
D. Complete Proof of Correction Form
1. Complete a Vehicle Emission Recall Proof of Correction Form and
supply it to the vehicle owner.
COMPLETION REPORTING AND REIMBURSEMENT
Claims for vehicles which have been serviced must be submitted on
the DIAL System Claims submitted will be used by Chrysler to record
recall service completions and provide dealer payments.
Use the following labor operation number and time allowance:
Labor
Operation Time
Number Allowance




















Replace oxygen sensor and catalytic converter 25617182 0.8 Hours
Add the cost of the recall parts package plus applicable dealer
allowance to your claim.
PARTS RETURN
Removed catalytic converters must be returned to the Warranty
Material Return Center.
NOTE: See Warranty Policy and Procedure Manual, Chapter 6, Subsection
H for complete recall claim processing and material return
instructions.
VEHICLE NOT AVAILABLE
If a vehicle is not available for service for a known reason, let us
know by filling out the pre-addressed Vehicle Disposition Form portion
of the Owner Notification Form, or describe the reason on a postcard
and mail to:
Chrysler Corporation 429-10-04
P.O. Box 1919
Detroit, Michigan 48231-1919
Following the above procedures will expedite the processing of your
claim.
If you have any questions or need assistance in completing this
action, please contact your Zone Service Office.
Customer Services Field Operations
Chrysler Corporation
CUSTOMER NOTIFICATION LETTER









\









\









\









\









\









\









\








EMISSIONS RECALL TO REPLACE YOUR VEHICLE'S
OXYGEN SENSOR AND CATALYTIC CONVERTER
Dear Jeep Vehicle Owner: