service JEEP CHEROKEE 1988 Service Repair Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 1988, Model line: CHEROKEE, Model: JEEP CHEROKEE 1988Pages: 1378, PDF Size: 19.9 MB
Page 10 of 1378
NOTE: Crankshaft journal diameters are indicated by a color coded
mark placed on the adjacent counterweight or cheek toward
the flanged (rear) end of crankshaft. Note color code to
determine proper bearing usage. Check oil clearance after
bearing installation.
Removal
1) Remove oil pan. See OIL PAN REMOVAL at end of ENGINE
section. See oil pump. See OIL PUMP under ENGINE OILING. Remove main
bearing cap.
2) Rotate crankshaft to position rod to be serviced at bottom
of stroke. Mark bearing cap and connecting rod. Remove bearing cap
with bearing. Push piston and rod assembly up to remove upper bearing.
Installation
1) Note color code on edge of bearings removed. Install
bearings. Using Plastigage method, check bearing clearances. Replace
bearings as necessary to obtain correct clearance. Bearings are
available in standard and undersize application.
2) If required, different sized upper and lower bearings may
be installed to obtain correct oil clearance. Tighten bolts to
specification. Check rod side play. Rotate crankshaft to ensure
freedom of movement. Reverse removal procedures for remaining
components. Tighten bolts to specification.
NOTE: Avoid combining bearing inserts in excess of .001" (.02 mm)
difference in size. Odd size inserts must be on bottom (rod
cap) side.
MAIN BEARINGS
Removal
1) Remove oil pan. See OIL PAN REMOVAL at end of ENGINE
section. Remove oil pump. See OIL PUMP under ENGINE OILING.
2) Ensure main bearing caps are marked for location. Rotate
crankshaft to remove bearings. Note color code on edge of bearing.
NOTE: Crankshaft journal diameters are indicated by a color coded
mark placed on the adjacent counterweight or cheek toward
the flanged (rear) end of crankshaft. Note color code to
determine proper bearing usage. Check oil clearance after
bearing installation.
Installation
1) Note color code on edge of bearings removed. Install
bearings. Ensure caps are installed in original location. Using
Plastigage method, check bearing clearances.
2) Replace bearings as necessary to obtain correct clearance.
Bearings are available in standard and undersize applications. If
required, different sized upper and lower bearings may be installed to
obtain correct oil clearance.
NOTE: If different sized bearings are used, the odd sized bearings
must all be uniform in location (upper or lower). DO NOT use
bearings with a thickness difference exceeding .001" (.02
mm).
3) Apply Loctite to corners of rear main bearing cap prior to
final installation. Tighten bolts to specification. Check crankshaft
end play. See CRANKSHAFT END PLAY. Rotate crankshaft to ensure freedom
of movement. Reverse removal procedures for remaining components.
Tighten bolts to specification.
Page 65 of 1378
ROD BEARING
NOTE: Crankshaft journal diameters are indicated by a color coded
mark placed on the adjacent counterweight or cheek toward
the flanged (rear) end of crankshaft. Note color code to
determine proper bearing usage. Check oil clearance after
bearing installation.
Removal
Remove oil pan. See OIL PAN REMOVAL at end of ENGINE section.
Rotate crankshaft to position rod to be serviced at bottom of stroke.
Mark bearing cap and connecting rod. Remove bearing cap with bearing.
Push piston and rod assembly up to remove upper bearing.
Installation
1) Note color code on edge of bearings removed. Install
bearings. Using Plastigage method, check bearing clearances. Replace
bearings as necessary to obtain correct clearance. Bearings are
available in standard and undersize application.
2) If required, different sized upper and lower bearings may
be installed to obtain correct oil clearance. Tighten bolts to
specification. Check rod side play. Rotate crankshaft to ensure
freedom of movement. Reverse removal procedure for remaining
components. Tighten bolts to specification.
NOTE: Avoid combining bearing inserts in excess of .001" (.02 mm)
difference in size.
MAIN BEARING
Removal
Remove oil pan. See OIL PAN REMOVAL at end of ENGINE section.
Ensure main bearing caps are marked for location. Remove bearing cap.
Rotate crankshaft to remove bearings. Note color code on edge of
bearing.
NOTE: Crankshaft main bearing journal diameters are indicated by a
color code. Color code is placed on the adjacent cheek
toward the flanged (rear) end of crankshaft for all except
the rear main. Rear main is color coded on the rear flange.
Note color code to determine proper bearing usage. Check oil
clearance after bearing installation.
Installation
1) Note color code on edge of bearings removed. Install
bearings. Ensure caps are installed in original location with arrow on
cap facing toward front of engine. Using Plastigage method, check
bearing clearances.
2) Replace bearings as necessary to obtain correct clearance.
Bearings are available in standard and undersize applications. If
required, different sized upper and lower bearings may be installed to
obtain correct oil clearance.
NOTE: If different sized bearings are used, odd sized bearings must
all be uniform in location (upper or lower). DO NOT use
bearings with a thickness difference exceeding
.001" (.02 mm).
3) Tighten bolts to specification. Check crankshaft end play.
See CRANKSHAFT END PLAY in this article. Rotate crankshaft to ensure
freedom of movement. Reverse removal procedure for remaining
components. Tighten bolts to specification.
Page 67 of 1378
Removal
Drain cooling system. Disconnect radiator and heater hoses
from pump. Remove drive belt(s). Remove fan shroud. Remove fan
assembly. Remove electric cooling fan (if equipped). Remove power
steering bracket from water pump. Remove water pump and gasket.
Installation
Ensure gasket surfaces are clean. Install water pump. Tighten
bolts to specification. Ensure pump turns freely. Reverse removal
procedures. Fill and purge air from cooling system.
NOTE: It may be necessary to remove heater hose to remove trapped
air if system cannot be purged using following procedures.
Cooling System Air Purge (Vehicles W/Coolant Recovery)
Fill system to proper level. Place heater control to "HEAT"
position and temperature control to "WARM" or "HIGH" position. Install
coolant caps. Operate engine to normal operating temperature. Shut off
engine and allow system to cool. Add coolant to recovery bottle.
Repeat procedure to obtain correct coolant level.
Cooling System Air Purge (Vehicles W/O Coolant Recovery)
Fill system to proper level. Place heater control to "HEAT"
position and temperature control to "WARM" or "HIGH" position. Operate
engine to normal operating temperature with radiator cap removed. Add
necessary coolant and install radiator cap.
NOTE: For further information on cooling systems, see appropriate
article in the ENGINE COOLING section.
LUBRICATION
CRANKCASE CAPACITY
Crankcase capacity for 4.0L is 5 1/2 qts. (5.2L) or 5 qts.
(4.7L) for 4.2L with oil filter change.
NORMAL OIL PRESSURE
Normal oil pressure should be 37-75 psi (2.6-5.3 kg/cm)
maximum above 1600 RPM. Minimum oil pressure should be 13 psi (.9
kg/cm
) at 600 RPM.
OIL PRESSURE REGULATOR VALVE
Oil pressure regulator valve is located in pump body. Valve
is nonadjustable and serviced as an assembly.
ENGINE OILING SYSTEM
Engine lubrication is provided by the distributor driven
gear-type oil pump. Oil is supplied through the full-flow oil filter
and into an internal oil passage. Internal passage provides oil to the
lifter bores. Oil is then routed to camshaft and crankshaft bearings.
Oil is supplied to rocker arms from the hydraulic lifters and through
the push rods.
OIL PUMP
Removal
Remove oil pan. See OIL PAN REMOVAL in this section. Remove
Page 98 of 1378
RVB Rear Vacuum Break
RWAL Rear Wheel Anti-Lock Brake
RWD Rear Wheel Drive
Recirc. Recirculate or Recirculation
Reg. Regulator
Rly. Relay
\
\
\
\
\
\
\
\f
"S" ABBREVIATION TABLE
"S" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
SAW Spark Angle Word
SBC Single Bed Converter
SBEC Single Board Engine Controller
SC Super Charged
SCC Spark Control Computer
SCS Air Suction Control Solenoid
SDM Supplemental Restraint System Diagnostic Module
SDU SRS Diagnostic Unit
SEN Sensor
SES Service Engine Soon
SFI Sequential (Port) Fuel Injection
SIG RTN Signal Return circuit
SIL Shift Indicator Light
SIR Supplemental Inflatable Restraint
SMEC Single Module Engine Controller
SOHC Single Overhead Cam
SOL or Sol. Solenoid
SPFI Sequential Port Fuel Injection
SPK Spark Control
SPOUT Spark Output Signal
SRS Supplemental Restraint System (Air Bag)
SS 3/4-4/3 Shift Solenoid circuit
SSI Solid State Ignition
STAR Self-Test Automatic Readout
STI Self Test Input circuit
STO Self-Test Output
SUB-O2 Sub Oxygen Sensor
Sen. or Sens. Sensor
Sol. Solenoid
Sprchg. Supercharger
Strg. Steering
Susp. Suspension
Sw. Switch
Sys. System
\
\
\
\
\
\
\
\f
"T" ABBREVIATION TABLE
"T" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
T.V. Throttle Valve
TAB Thermactor Air By-Pass
TAC Thermostatic Air Cleaner
TAD Thermactor Air Diverter
TAN Tan
TBI Throttle Body Injection
Page 99 of 1378
TCC Torque Converter Clutch
TCCS Toyota Computer Control System
TDC Top Dead Center
TDCL Total Diagnostic Communication Link
TFI Thick Film Ignition system
TGS Top Gear Switch (cancels SIL in top gear)
THERMAC Thermostatic Air Cleaner
THS Transmission Hydraulic Switch
TP/TPS Throttle Position Sensor
TPI Tuned Port Injection
TPS Throttle Position Sensor/Switch
TS Temperature Sensor
TSB Technical Service Bulletin
TTS Transmission Temperature Switch
TV Thermovalve
TWC Three-Way Catalyst
Temp. Temperature
Trans. Transaxle/Transmission
\
\
\
\
\
\
\
\f
"V" ABBREVIATION TABLE
"V" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
V Valve
VAF Vane Air Flow sensor or circuit
VAPS Variable Assist Power Steering
VAT Vane Air Temperature
VATS Vehicle Anti-Theft System
VBATT Vehicle Battery Voltage
VCC Viscous Converter Clutch
VIN Vehicle Identification Number
VIO Violet
VLR Volt Loop Reserve
VM Vacuum Modulator
VM Vane Meter
VOM Volt-Ohmmeter (Analog)
VPWR Vehicle Power supply voltage (10-14 volts)
VREF Voltage Reference (ECA supplied reference voltage
VRV Vacuum Regulator Valve
VSC Vehicle Speed Control sensor or signal
VSS Vehicle Speed Sensor or signal
VSV Vacuum Switching Valve
Vac. Vacuum
Volt. Voltage
\
\
\
\
\
\
\
\f
"W" ABBREVIATION TABLE
"W" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
W/ With
W/O Without
WAC WOT A/C Cut-off switch or circuit
WAC Wide Open Throttle A/C Switch
WHT White
WOT Wide Open Throttle
YEL Yellow
Page 101 of 1378
\003
A/C C O M PR ESSO R O IL C HEC KIN G
1988 J e ep C hero ke e
A/C General Servicing
COMPRESSOR OIL CHECK
* PLEASE READ THIS FIRST *
CAUTION: When discharging air conditioning system, use only approved
refrigerant recovery/recycling equipment. Make every attempt
to avoid discharging refrigerant into the atmosphere.
ISOLATING COMPRESSOR - GRAND WAGONEER ONLY
1) Connect service gauge set to the compressor service valves
and open compressor valves slightly (turn clockwise). Start engine and\
operate air conditioning. Slowly turn compressor suction valve
clockwise toward closed (front-seated) position.
2) When suction pressure is reduced to zero or less, turn off
engine and compressor and quickly turn suction valve stem in to full
front-seated position. Suction pressure should be slightly above zero.
Turn discharge valve into front-seated position.
3) To check oil lever, slowly open crankcase plug to relieve
any remaining pressure. After oil level is correct, cap service gauge
parts on both valves. Back-seat suction service valve to allow
refrigerant to enter compressor. Open discharge valve halfway.
4) Loosen discharge service valve cap, allowing refrigerant
pressure to force air out of compressor. Back-seat service valve and
tighten cap. Compressor is now ready for operation.
REFRIGERANT OIL
Only new, pure, moisture-free refrigerant oil should be used
in the air conditioning system. This oil is highly refined and
dehydrated to a point where moisture content is less than 10 parts per
million. The oil container must be tightly closed at all times when
not in use, or moisture will be absorbed from the air and introduced
into the refrigeration system.
DISCHARGING SYSTEM
CAUTION: When discharging air conditioning system, use only approved
refrigerant recovery/recycling equipment. Make every attempt
to avoid discharging refrigerant into the atmosphere.
If compressor has stem-type service valves, it can be
isolated and removed without discharging entire system. Otherwise,
discharge system completely using approved refrigerant
recovery/recycling equipment before loosening any fittings.
DISCONNECTING LINES & FITTINGS
After system is discharged, carefully clean area around all
fittings to be opened. Always use 2 wrenches when tightening or
loosening fittings to avoid twisting or distorting lines. Cap or plug
all openings as soon as lines are removed. Do not remove caps until
immediately before connections are made. This will keep entry of air
and moisture to a minimum, reducing the chance of damage to
components.
Page 102 of 1378
PLACING SYSTEM IN OPERATION
After component service or replacement has been completed and
all connections have been made, evacuate system throughly with a
vacuum pump. Charge system with proper amount of refrigerant and
perform a leak test. Be sure to check all fittings that have been
opened. After system has been leak tested, make a system performance
check.
SANDEN SD508 5-CYLINDER OIL CHECKING
1) Discharge system using approved refrigerant
recovery/recycling equipment. Remove compressor belt and loosen
mounting bolts. Rotate compressor in brackets until filler plug is at
top. Clean area around filler plug and remove plug slowly. Rotate
front hub plate so notch in lobe is 110 degrees from the bottom. This
rotates ball end of top piston to align with oil fill port and allows
clearance for dipstick. See Fig. 1.
2) Insert compressor dipstick diagonally from right to left
until stop on dipstick contacts filler plug surface. Remove dipstick
and note oil fill level. Each mark on dipstick represents one ounce
of oil. Add oil if necessary to reach 3-4 ounce level.
Fig. 1: Sanden 5-Cylinder Oil Level Checking
YORK - 2-CYLINDER - PURGINE COMPRESSOR
Page 103 of 1378
1) Remove gauge set and place caps on service valve ports.
Back-seat the suction service valve to allow refrigerant to enter
compressor.
2) Loosen discharge port valve slightly. Loosen valve port
cap to allow refrigerant to force out air from compressor. Back-seat
the discharge valve and tighten the port cap. Compressor is ready for
service.
YORK - 2-CYLINDER COMPRESSOR OIL CHECKING
1) Operate system for 10 minutes, then stop and isolate
compressor. Loosen filler plug slowly to release any pressure in
crankcase.
2) Use dipstick to check oil level. See Fig. 2. Add oil as
necessary, then install plug with new "O" ring. Purge compressor of
air.
Fig. 2: York A/C Compressor Oil Level Dipstick (Check oil w/ shaft
keyway facing head)
Courtesy of Chrysler Motors.
Page 104 of 1378
\003
A/C -H EA TE R S YSTE M - M AN UAL
1988 J e ep C hero ke e
1988 Manual A/C-Heater Systems
JEEP
* PLEASE READ THIS FIRST *
CAUTION: When discharging air conditioning system, use only approved
refrigerant recovery/recycling equipment. Make every attempt
to avoid discharging refrigerant into the atmosphere.
DESCRIPTION
On Cherokee, Comanche and Wagoneer, the Climate Control
System is an integral assembly combining air conditioning, heating and
ventilating capabilities for models with air conditioning. The A/C
registers are built into instrument panel.
On Wrangler models, a dual flow unit with the capability of
recirculating air or drawing air from outside is used. It incorporates
under-dash registers and uses a blend-air type system.
The A/C components include a compressor, condenser, receiver-
drier, a sight glass (in the receiver-to-evaporator line) and
evaporator housing. Evaporator housing contains evaporator core,
expansion valve, thermostat, wiring and drain tube. Blower motor and
fan are located in blower housing, which is attached to evaporator
housing.
Vents provided in evaporator housing are adjustable to direct
air to different positions in vehicle's interior. System controls
include fan and temperature control knobs built into lower evaporator
housing assembly or temperature and mode levers on control panel
integrated with instrument panel.
OPERATION
A/C SYSTEM CONTROLS
Temperature & Fan Control Knobs
(Wrangler)
The right rotary control knob allows selection of desired
temperature. Knob has "OFF" "1", "2" and "3" positions for different
levels of cooling. The left rotary fan switch (knob) controls blower
motor speed. Knob has "OFF", "LOW", "MED" and "HI" positions. Fan will
operate unless mode control lever is in "OFF" position.
The A/C fan switch is a 3-speed unit used in conjunction with
a blower motor resistor. Fan switch controls low, medium and high
speed operation. Switch may be serviced by removing access plate
located on lower evaporator core housing, below control panel.
The A/C temperature control switch has a thermostat unit
built-in. Cooling adjustment is done by turning knob in a clockwise
rotation. For fast, efficient system operation in hot weather, vehicle
should be purged of hot air by driving about 2-3 city blocks with at
least one window open. During this time, temperature control knob
should be rotated clockwise to "MAX" position and fan control knob
placed in "HI" position. This allows evaporator to pre-cool and avoid
typical first blast of warm air.
Temperature Control Panel
(Cherokee, Comanche & Wagoneer)
The upper temperature control (mode) lever includes "MAX",
"NORM", "BI-LEVEL", "VENT", "HEAT" and "OFF" positions. At the far end
Page 107 of 1378
housing attaching nuts from studs on engine compartment side of dash
panel. Remove evaporator drain tube.
4) Remove right kick panel. Detach instrument panel support
bolt. Gently pull on right side of dash, then rotate housing downward
and toward rear of vehicle to disengage housing studs from dash panel.
Remove evaporator-blower housing.
5) To remove heater core, detach retaining screws. Remove
heater core by pulling straight out of housing. To remove evaporator
core, detach top housing retaining screws, then remove top of
evaporator housing.
6) Remove thermostatic switch and capillary tube. Detach 2
evaporator retaining screws and lift evaporator core from housing.
Remove expansion valve from evaporator.
Installation
1) To install components, reverse removal procedure. When
installing evaporator core, install thermostatic switch and capillary
tube before installing top of housing.
2) When installing heater core, ensure seal is properly
cemented in place to prevent it from moving when blower assembly is
installed. Evacuate, leak test, recharge and check A/C system
operation.
NOTE: The evaporator housing mounting location is similar to
Wrangler, except blower motor is mounted horizontally to
firewall.
Removal (Wrangler)
1) Discharge system using approved refrigerant
recovery/recycling equipment. Disconnect inlet line at compressor.
Disconnect hose, at quick-disconnect coupling, between receiver-drier
and evaporator. Remove hose clamps and dash grommet retaining screws.
See Fig. 2 .
Fig. 2: Wrangler Evaporator Housing Mounting Screw Locations
Courtesy of Chrysler Motors.
NOTE: It is not necessary to discharge system to service blower
motor. Evaporator housing may be lowered from instrument