roof JEEP CHEROKEE 1995 Service Owner's Manual

INSPECTION
Inspect the rear shoulder/lap belts and buckles. Re-
place any belt that is either cut, frayed, torn or dam-
aged in any way. Replace the shoulder belt if the
retractor is damaged or inoperative.
INSTALLATION
(1) Position the shoulder belt buckle and the lap
belt/buckle anchor plates on the floor panel.
(2) Install the anchor bolts. Tighten the bolts to 37
Nzm (27 ft-lbs) torque.
(3) Position the shoulder belt at the roof rail and
install the upper anchor bolt. Tighten the bolt to 37
Nzm (27 ft-lbs) torque.
(4) Route the shoulder belt through the quarter
trim panel slot. Install the retractor support on the
rear quarter rail. Tighten the screw to 5 Nzm (45 in-
lbs) torque.
(5) Install the quarter trim panel.
(6) Install the shoulder belt lower anchor bolt.
Tighten the bolt to 37 Nzm (27 ft-lbs) torque.
(7) Return the rear seat to the normal position and
engage the latch.
HEADLINERÐXJ
The upper trim moldings and the headliner are at-
tached to the roof rail with a combination of screws,
velcro strips, clip retainers and rail retainers (Fig. 1).
To remove a headliner, all of the upper trim mold-
ings must be removed from the perimeter of the
headliner along with (as applicable):
²Assist handles.
²Sunvisors.
²Dome/cargo lamps.
²Overhead console.
²Keyless entry receiver module.
²Sound bar.
²All other attached/overlapping components.
Refer to the appropriate removal and installation pro-
cedure locate in this section or in Group 8, Electrical.
REMOVAL
CAUTION: The headliner is a one-piece, molded
component. It has limited flexibility and must not be
bent during removal/installation.
(1) Remove the upper trim moldings from the pe-
rimeter of the headliner (Fig. 2 and 3).
Fig. 5 Shoulder Belt Retractor Support Removal/
InstallationFig. 1 Headliner Trim Moldings
Fig. 2 Upper Trim MoldingÐ4-Door XJ Vehicles
Fig. 3 Liftgate Trim Molding
23 - 92 INTERIOR COMPONENTSÐXJJ

(2) Ensure that all the retainer clips, screws and
Velcro strips are disengaged before removing the
headliner.
HEADLINER INSTALLATION
(1) When installing a headliner, ensure that the re-
tainer clips and rails are installed (Fig. 4 and 5).
(2) Install the upper trim moldings around the pe-
rimeter of the headliner. Tighten the retaining
screws to 1 Nzm (11 in-lbs) torque.
(3) As applicable, install:
²Assist handles.
²Sunvisors.
²Dome/cargo lamps.
²Overhead console.
²Keyless entry receiver module.
²Sound bar.
²All other attached/overlapping components.
DOME LAMPÐXJ
REMOVAL
(1) Remove the dome lamp lens by squeezing both
sides to release the retaining clips. Pull downward to
remove the lens.
(2) Remove the speed nuts (Fig. 6).
(3) Disconnect the wire harness connector.
(4) Remove the lamp from the headliner.
INSTALLATION
(1) Connect the dome lamp wire harness connector.
(2) Position the dome lamp in the headliner hole
and install the speed nuts.
(3) Install the dome lamp lens.
OVERHEAD CONSOLEÐXJ
Refer to Group 8C, Overhead Console for removal
and installation procedure.
KEYLESS ENTRY RECEIVERÐXJ
Refer to Group 8P, Keyless Entry for removal and
installation procedure.
SUNVISORSÐXJ
REMOVAL
(1) Remove the screws that attach the sunvisor
arm support bracket to the headliner and the roof
panel (Fig. 7).
(2) Detach the sunvisor from the support clip.
(3) Remove the sunvisor from the vehicle.
(4) Remove the retaining screw and support clip.
Fig. 4 Headliner Retainer Clip and Retainer Rail
Fig. 5 Headliner Correctly Installed
Fig. 6 Dome Lamp
JINTERIOR COMPONENTSÐXJ 23 - 93

INSTALLATION
(1) Install the support bracket and the retaining
screw. Tighten the screw to 1 Nzm (9 in-lbs) torque.
(2) Position the sunvisor in the support clip and
align the arm support bracket holes with the head-
liner holes.
(3) Install the screws that attach the sunvisor arm
support bracket to the headliner and the roof panel.
Tighten the screws to 4 Nzm (35 in-lbs) torque.
SOUND BARÐXJ
REMOVAL
(1) Disconnect battery negative cable.
(2) Remove left and right upper trim molding.
(3) Remove sound bar screws.
(4) Separate sound bar from roof.
(5) Disconnect speaker connector.
(6) Disconnect cargo lamp connector.
(7) Remove sound bar from vehicle (Fig. 8).
INSTALLATION
(1) Position sound bar in vehicle.
(2) Connect speaker connecter.
(3) Connect cargo lamp connector.
(4) Position sound bar at roof.
(5) Install sound bar screws.
(6) Install left and right upper trim molding.
(7) Connect battery negative cable.
CARGO LAMPÐXJ
REMOVAL
(1) Remove the cargo lamp lens (Fig. 8) by squeez-
ing both sides to release the retaining clips. Pull
downward to remove the lens.
(2) Remove the push nuts.
(3) Disconnect the wire harness connector.
(4) Remove the lamp from the sound bar.
INSTALLATION
(1) Connect the cargo lamp wire harness connector.
(2) Position the cargo lamp in the sound bar hole
and install the push nuts.
(3) Install the cargo lamp lens.
MINI-FLOOR CONSOLEÐXJ
Mini-consoles are installed in XJ vehicles with and
without a transmission floor shift (Fig. 1).
PARKING BRAKE HANDLE COVERÐXJ
REMOVAL
(1) Detach the rear of the cover from the base and
pivot it upward (Fig.2).
(2) Remove the retaining screws from the cover
base.
(3) Remove the trim cover from the from the floor.
INSTALLATION
(1) Position the cover on the floor and install the
retaining screws.
(2) Pivot the cover to the closed position and en-
gage the locking tab.
MINI-CONSOLE WITH FLOOR SHIFTÐXJ
REMOVAL
(1) Remove the transmission shift lever handle/
knob. For vehicles with an automatic transmission,
pull the handle straight up. For vehicles with a man-
ual transmission, loosen the locknut and un-thread
the shift knob from the shaft.
(2) Remove the automatic transmission and trans-
fer case shift indicator bezel by prying upward to re-
lease them (Fig. 3).
(4) Disconnect the lamp socket from the bezel.
(5) Remove the console retaining screws.
(6) Disconnect the wire harness connector.
Fig. 7 Sunvisor Removal/Installation
Fig. 8 Sound Bar Removal/Installation
23 - 94 INTERIOR COMPONENTSÐXJJ

EXTERIOR COMPONENTS
INDEX
page page
Battery TrayÐYJ......................... 110
Body Side Step MoldingÐYJ................ 115
Body Stripes/DecalsÐYJ................... 116
Cowl Grille and ScreenÐYJ................ 109
Cowl Weatherstrip SealÐYJ................ 109
Exterior Nameplates (Adhesive-Backed)ÐYJ.... 120
External Spare/Wheel Tire CarrierÐYJ........ 133
Fender FlareÐYJ........................ 114
Fender Inner Splash ShieldsÐYJ............. 116
Fender Splash ApronsÐYJ................. 115
FendersÐYJ............................ 110
Fuel Filler Protector/NozzleÐYJ............. 121
Half Metal Door Mirror (External)ÐYJ......... 121
Hard Top Liftgate GlassÐYJ................ 124
Hard Top RepairÐYJ..................... 127
Hard Top Roof VentÐYJ................... 127
Hard TopÐYJ........................... 126Hood AlignmentÐYJ...................... 107
Hood Insulator PanelÐYJ.................. 107
Hood Safety LatchÐYJ.................... 109
HoodÐYJ.............................. 107
Liftgate Glass Weatherstrip Seal ReplacementÐYJ. 125
Radiator Grille AppliqueÐYJ................ 104
Soft Top Service InformationÐYJ............. 127
Soft Top ServiceÐYJ..................... 129
Sport BarÐYJ........................... 132
Tailgate AdjustmentÐYJ................... 121
Tailgate HingeÐYJ....................... 121
Tailgate Latch and Release HandleÐYJ........ 122
Tailgate Latch StrikerÐYJ.................. 123
Tailgate Lock CylinderÐYJ................. 122
Tailgate Weatherstrip SealÐYJ.............. 123
TailgateÐYJ............................ 121
Wheelhouse Splash LinersÐYJ.............. 115
RADIATOR GRILLE APPLIQUEÐYJ
REMOVAL
(1) Raise the hood.
(2) Remove the headlamp bezels (Fig. 1).(3) Remove the headlamp bulb retainer screws
(Fig. 2).
(4) Disconnect and remove the headlamps and
buckets as a unit (Fig. 2).
Fig. 1 Grille Applique, Headlamp Bezel and Grille Panel
23 - 104 EXTERIOR COMPONENTSÐYJJ

HARD TOP ROOF VENTÐYJ
REMOVAL/INSTALLATION
(1) Remove the roof vent retaining screw from the
spring nut (Fig. 1).
(2) Remove the roof vent from the hard top.
(3) Position the roof vent on the hard top and in-
stall the retaining screw.
HARD TOP REPAIRÐYJ
The hard top fiberglass material can be repaired.
The required repair materials include:
²Fiberglass mat or cloth.
²Fiberglass resin and hardener.
²structural adhesive (3M brand or an equivalent
product).
²Glazing putty.
²Aluminum foil.
²Plastic spreader.
HARD TOP HOLE REPAIR
(1) Use a grinder to remove the paint and outline
the damaged area. Use a grade 24 grit disc for paint
removal.
(2) Grind the outlined surface area again to a 50
grit disc to prevent coarse scratches from appearing
in the final finish.
(3) If cracks extend from the hole, it will be neces-
sary to stop-drill the crack(s) with a 3-mm (1/8-in) di-
ameter drill bit.
(4) Position a fiberglass mat or cloth on the repair
surface area. Cut the mat to allow a 2.5-cm (1-in)
overlap of the repair surface area.
(5) Clean the repair surface area.
(6) Place the fiberglass cloth on aluminum foil.
(7) Pour the fiberglass resin into a clean container.
(8) Mix the appropriate amount of hardener and
resin. Follow the manufacturers instructions.
(9) Apply the hardener/resin mixture to both sides
of the fiberglass cloth.(10) Place the fiberglass cloth over the repair sur-
face area. Next, place the aluminum foil over the
cloth. Use a plastic spreader to smooth-out the cloth
and resin. Use firm pressure to remove air bubbles
and to smooth-out the cloth.
(11) Allow the resin to cure.
(12) Smooth-out the surface area to the contour of
the hard top with a 50-grit disc.
(13) Apply plastic filler to complete the repair. Fin-
ish smoothing the surface area with 80-grit paper.
(14) Repeat the previous step on the inside surface
area of the hard top.
(15) Featheredge the repaired surface area.
(16) Prime the repaired surface area with Ditzler
Epoxy Chromate Primer (DP-40/401), or an equiva-
lent product.
(17) Apply surface primer to the surface area.
(18) Sand the surface area for paint preparation.
After sanding, re-prime the surface area, if necessary.
(19) Prime the surface area for the color coat.
(20) Color coat the repaired surface area.
FRACTURE REPAIR
(1) Use a grinder to remove the paint (from both,
the inner and outer surface areas of the hard top)
and to outline the damaged area.
(2) Stop-drill the crack(s) with a 3-mm (1/8-in) di-
ameter drill bit.
(3) Bevel the edges of the crack(s) on both sides
with a rotary file.
The edges should be beveled on the inside
and outside of the top to ensure sufficient sur-
face area for good bonding.
(4) Complete the repairs with fiberglass cloth and
resin as described above in the hard top hole repair
procedure.
TEXTURED PAINT REPAIR
The textured paint applied to hard tops is available
from Mopar Parts sources. The paint supplied will
duplicate the original texture on the hard top.
SOFT TOP SERVICE INFORMATIONÐYJ
The soft top fabric consists of the top cover and the
side and rear curtains (Fig. 4). The top cover is sup-
ported by a tubular bow (frame) and is attached to
the upper side retainers (above the doors) with
snap-on retainers (Fig. 5).
Fig. 3 Wire Harness Connection
JEXTERIOR COMPONENTSÐYJ 23 - 127

GENERAL INFORMATION; POWER LOCKS . . 8P-1
GENERAL INFORMATION; POWER
MIRRORS...........................8T-1
GENERAL INFORMATION; POWER SEATS . . 8R-1
GENERAL INFORMATION; POWER
WINDOWS...........................8S-1
GENERAL INFORMATION; PROPELLER
SHAFTS.............................16-1
GENERAL INFORMATION; REAR
SUSPENSION AND AXLES........3-13,3-1,3-9
GENERAL INFORMATION; REAR
WINDOW DEFOGGER..................8N-1
GENERAL INFORMATION; RESTRAINT
SYSTEMS...........................8M-1
GENERAL INFORMATION; SPLICE
INFORMATION (XJ).................8W-70-1
GENERAL INFORMATION; SPLICE
INFORMATION (XJ-RHD)............8W-70-1
GENERAL INFORMATION; SPLICE
INFORMATION (YJ).................8W-70-1
GENERAL INFORMATION; SPLICE
LOCATIONS (XJ)...................8W-95-1
GENERAL INFORMATION; SPLICE
LOCATIONS (XJ-RHD)...............8W-95-1
GENERAL INFORMATION; SPLICE
LOCATIONS (YJ)...................8W-95-1
GENERAL INFORMATION; STEERING . 19-48,19-1
GENERAL INFORMATION;
TRANSMISSION AND TRANSFER CASE . . 21-165,
21-283,21-307,21-33,21-67,21-70,21-1
GENERAL INFORMATION; TURN SIGNAL
AND HAZARD WARNING SYSTEMS.......8J-1
GENERAL INFORMATION; VEHICLE
SPEED CONTROL SYSTEM..............8H-1
GENERAL INFORMATION; WHEELS AND
TIRES..........................22-1,22-6
GENERAL INFORMATION - XJ............8K-1
GENERAL INFORMATION - YJ...........8K-10
GENERAL SERVICE INFORMATION; BODY
COMPONENTSÐXJ VEHICLES.........23-102
GENERAL SERVICE INFORMATION;
BRAKES.........................5-15,5-60
GENERAL SERVICEÐXJ, STEERING
COLUMN...........................19-47
GENERAL SPECIFICATIONS, 30RH/32RH . 21-335
GENERAL SPECIFICATIONS, AW-4......21-337
GENERATOR.........................8B-6
GENERATOR DIAGNOSTIC TROUBLE
CODE..............................8A-22
GENERATOR FIELDÐPCM OUTPUT......14-27
GENERATOR LAMPÐPCM OUTPUT......14-27
GENERATOR RATINGS................8A-23
GENERATOR REMOVE/INSTALLÐLEFT-
HAND DRIVE.........................8B-6
GENERATOR REMOVE/INSTALLÐRIGHT-
HAND DRIVE.........................8B-7
GENERATOR SPECIFICATIONS...........8B-8
GENERATOR SPLASH SHIELD...........13-13
GLASS AND DOOR OPENING
WEATHERSTRIP SEALSÐXJ, DOOR
WINDOW...........................23-55
GLASS CHANNEL REPLACEMENTÐYJ,
DOOR FRAME......................23-142
GLASS GRID, REAR WINDOW.......8N-1,8N-2
GLASS GRID REPAIRS, REAR WINDOW . . . 8N-3
GLASS REGULATOR HANDLEÐYJ,
FULL-METAL DOOR WINDOW..........23-136
GLASS REGULATORÐXJ, FRONT DOOR
WINDOW...........................23-42
GLASS REGULATORÐXJ, REAR DOOR
WINDOW...........................23-44
GLASS REGULATORÐYJ, FULL-METAL
DOOR WINDOW....................23-138
GLASS REPLACEMENTÐXJ,
WINDSHIELD........................23-69
GLASS, STATIONARY.................23-144
GLASS, STATIONARY WINDOW..........23-66
GLASS WATER LEAK DETECTION AND
REPAIRÐXJ, STATIONARY.............23-76
GLASS WATER LEAK DETECTION AND
REPAIRÐYJ, STATIONARY............23-150
GLASS WEATHERSTRIP SEAL
REPLACEMENTÐYJ, LIFTGATE
.........23-125
GLASSÐXJ, FRONT DOOR WINDOW
.....23-43
GLASSÐXJ, LIFTGATE WINDOW
........23-74
GLASSÐXJ, REAR DOOR STATIONARY
WINDOW
...........................23-46
GLASSÐXJ, REAR DOOR WINDOW
......23-45GLASSÐXJ, REAR QUARTER VENT
WINDOW...........................23-73
GLASSÐYJ, FULL-METAL DOOR VENT
WINDOW..........................23-137
GLASSÐYJ, FULL-METAL DOOR
WINDOW..........................23-139
GLASSÐYJ, HARD TOP LIFTGATE......23-124
GLASSÐYJ, HARD TOP QUARTER
WINDOW..........................23-149
GLASSÐYJ, WINDSHIELD............23-146
GLASS/REAR QUARTER PLASTIC
INSERTÐXJ, REAR QUARTER
WINDOW...........................23-73
GLOVE BOX LAMP; INTERIOR LIGHTING
(XJ).............................8W-44-1
GLOVE BOX LAMP; INTERIOR LIGHTING
(XJ-RHD).........................8W-44-1
GLOVE BOXÐYJ....................23-152
(GOP)ÐXJ, GRILLE AND GRILLE
OPENING PANEL......................23-3
GOVERNOR AND PARK GEAR OVERHAUL . 21-127
GOVERNOR AND PARK GEAR SERVICE . . 21-105
GRAB, REAR BRAKE....................5-7
GRID, REAR WINDOW GLASS.......8N-1,8N-2
GRID REPAIRS, REAR WINDOW GLASS . . . 8N-3
GRILLE AND GRILLE OPENING PANEL
(GOP)ÐXJ...........................23-3
GRILLE AND SCREENÐXJ, COWL.......23-12
GRILLE AND SCREENÐYJ, COWL......23-109
GRILLE APPLIQUEÐYJ, RADIATOR.....23-104
GRILLE OPENING PANEL (GOP)ÐXJ,
GRILLE.............................23-3
GRILLEÐXJ, AIR EXHAUST............23-25
GROUND CLEARANCE AND RAMP
ANGLE..............................0-11
GROUND, CLUSTER; INSTRUMENT
CLUSTER (XJ).....................8W-40-3
GROUND, CLUSTER; INSTRUMENT
CLUSTER (XJ-RHD)................8W-40-2
GROUND, POWER....................14-24
GROUND, POWER (DEVICE); FUEL/
IGNITION (XJ).....................8W-30-5
GROUND, POWER (DEVICE); FUEL/
IGNITION (YJ).....................8W-30-5
GROUND, POWER (DEVICE); FUEL/
IGNITION (XJ-RHD)................8W-30-5
GROUP, HOW TO USE THIS; WIRING
DIAGRAMS (XJ)......................8W-1
GROUP, HOW TO USE THIS; WIRING
DIAGRAMS (XJ-RHD)..................8W-1
GROUP, HOW TO USE THIS; WIRING
DIAGRAMS (YJ)......................8W-1
GUARD/EDGE PROTECTOR STRIPÐXJ,
DOOR EDGE........................23-54
GUARDÐXJ, BRUSH...................23-3
GUIDES AND CHARTS, DIAGNOSIS......21-77
HALF METAL DOOR MIRROR
(EXTERNAL)ÐYJ....................23-121
HALF-METAL DOOR LATCH STRIKERÐ
YJ ...............................23-135
HALF-METAL SOFT TOP DOORÐYJ.....23-134
HAND DRIVE, AUTOMATIC BELT
TENSIONERÐXJ MODELS WITH
RIGHT..............................7-42
HAND DRIVE, BELT SERVICEÐEXCEPT
RIGHT..............................7-40
HAND DRIVE, BELT SERVICEÐXJ
MODELS WITH RIGHT..................7-42
HAND DRIVE (RHD), BELT TENSIONÐ
EXCEPT RIGHT.......................7-38
HAND DRIVE (RHD), BELT TENSIONÐ
RIGHT..............................7-38
HAND DRIVE (RHD) MODELS, BELT
TENSIONÐEXCEPT RIGHT..............7-45
HAND DRIVE VEHICLES, RIGHT..........23-1
HANDLE COVERÐXJ, PARKING BRAKE . . . 23-94
HANDLEÐXJ, ASSIST.................23-89
HANDLEÐXJ, DOOR EXTERNAL.........23-48
HANDLEÐYJ, FULL-METAL DOOR
ASSIST
...........................23-136
HANDLEÐYJ, FULL-METAL DOOR LATCH
EXTERNAL RELEASE
.................23-140
HANDLEÐYJ, FULL-METAL DOOR LATCH
INSIDE RELEASE AND LOCK
...........23-137
HANDLEÐYJ, FULL-METAL DOOR
WINDOW GLASS REGULATOR
.........23-136
HANDLEÐYJ, TAILGATE LATCH AND
RELEASE
..........................23-122HANDLING, AIRBAG MODULE...........8M-2
HARD PEDAL OR HIGH PEDAL EFFORT.....5-6
HARD TOP LIFTGATE GLASSÐYJ.......23-124
HARD TOP QUARTER WINDOW
GLASSÐYJ........................23-149
HARD TOP REPAIRÐYJ..............23-127
HARD TOP ROOF VENTÐYJ...........23-127
HARD TOPÐYJ.....................23-126
HARDTOP DOME/CARGO LAMP BULB
REPLACEMENTÐYJ VEHICLES..........8L-31
HAS A MISS, INJECTOR DIAGNOSISÐ
VEHICLE RUNS ROUGH AND/OR........14-52
HAZARD FLASHERS; TURN SIGNALS
(XJ).............................8W-52-1
HAZARD FLASHERS; TURN SIGNALS
(XJ-RHD).........................8W-52-1
HAZARD FLASHERS; TURN SIGNALS
(YJ).............................8W-52-1
HAZARD WARNING SYSTEM.............8J-1
HAZARD WARNING SYSTEM - YJ.........8J-4
HCU DIAGNOSIS, ANTILOCK ECU..........5-3
HCU INSTALLATION (XJ)................5-43
HCU INSTALLATION (YJ)................5-44
HCU OPERATION......................5-36
HCU REMOVAL (XJ)...................5-41
HCU REMOVAL (YJ)...................5-44
HEAD COVER, ENGINE CYLINDER....9-22,9-64
HEAD, ENGINE CYLINDER...........9-25,9-67
HEAD GASKET FAILURE DIAGNOSIS,
ENGINE CYLINDER.....................9-5
HEAD NOT REMOVED, VALVE
COMPONENT REPLACEÐCYLINDER . . . 9-23,9-65
HEADLAMP ALIGNMENT
PREPARATIONÐXJ....................8L-6
HEADLAMP ALIGNMENT
PREPARATIONÐYJ...................8L-22
HEADLAMP ALIGNMENTÐXJ............8L-6
HEADLAMP ALIGNMENTÐYJ...........8L-22
HEADLAMP BULB REPLACEMENTÐXJ.....8L-7
HEADLAMP BULB REPLACEMENTÐYJ....8L-23
HEADLAMP DELAY FUNCTION TROUBLE
DIAGNOSISÐXJ.....................8L-14
HEADLAMP DELAY MODULE; FRONT
LIGHTING (XJ)....................8W-50-2
HEADLAMP DELAY MODULE; FRONT
LIGHTING (XJ-RHD)................8W-50-1
HEADLAMP DELAY MODULE
REPLACEMENTÐXJ..................8L-14
HEADLAMP DELAY MODULEÐXJ,
SENTINEL..........................8L-14
HEADLAMP DIAGNOSIS...........8L-20,8L-2
HEADLAMP DIMMER SWITCH
REPLACEMENTÐYJ..................8L-26
HEADLAMP OR PANEL DIMMER SWITCH
REMOVE/INSTALL....................8E-42
HEADLAMP RELAY; FRONT LIGHTING
(XJ-RHD).........................8W-50-1
HEADLAMP SWITCH REMOVE/INSTALL . . . 8E-19
HEADLAMP SWITCH (XJ ONLY)......8U-1,8U-3
HEADLAMP SWITCHÐXJ..............8L-10
HEADLAMP SWITCHÐYJ..............8L-26
HEADLAMP/FOG LAMP ADJUSTMENT
USING ALIGNMENT SCREENÐXJ.........8L-7
HEADLAMP/FOG LAMP ADJUSTMENT
USING ALIGNMENT SCREENÐYJ........8L-23
HEADLAMPS; FRONT LIGHTING (XJ) . . . 8W-50-1
HEADLAMPS; FRONT LIGHTING
(XJ-RHD).........................8W-50-1
HEADLAMPS; FRONT LIGHTING (YJ) . . . 8W-50-1
HEADLAMPS; LUBRICATION AND
MAINTENANCE.......................0-33
HEADLINERÐXJ.....................23-92
HEAT SHIELDS......................14-13
HEAT SHIELDS, EXHAUST...............11-1
HEATED OXYGEN SENSOR; FUEL/
IGNITION (XJ).....................8W-30-3
HEATED OXYGEN SENSOR; FUEL/
IGNITION (YJ).....................8W-30-3
HEATED OXYGEN SENSOR; FUEL/
IGNITION (XJ-RHD)
................8W-30-3
HEATED REAR WINDOW; HEATED REAR
WINDOW (XJ)
.....................8W-48-1
HEATED REAR WINDOW; HEATED REAR
WINDOW (XJ-RHD)
.................8W-48-1
HEATED REAR WINDOW; HEATED REAR
WINDOW (YJ)
.....................8W-48-1
HEATER; AIR CONDITIONING/HEATER
(YJ)
.............................8W-42-1
12 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

REPLACEMENTÐXJ VEHICLES, DRIVE
AXLE ASSEMBLY; REAR SUSPENSION
AND AXLES......................3-14,3-31
REPLACEMENTÐXJ, WINDSHIELD
GLASS.............................23-69
REPLACEMENTÐYJ, BACK-UP/REAR
TURN SIGNAL/TAIL LAMP BULB.........8L-28
REPLACEMENTÐYJ, DOOR FRAME
GLASS CHANNEL...................23-142
REPLACEMENTÐYJ, DOOR
WEATHERSTRIP SEAL................23-142
REPLACEMENTÐYJ, DRL MODULE......8L-30
REPLACEMENTÐYJ, FOG LAMP.........8L-25
REPLACEMENTÐYJ, FOG LAMP SWITCH . 8L-26
REPLACEMENTÐYJ, FRONT PARK/TURN
SIGNAL LAMP BULB..................8L-25
REPLACEMENTÐYJ, HEADLAMP BULB . . . 8L-23
REPLACEMENTÐYJ, HEADLAMP
DIMMER SWITCH....................8L-26
REPLACEMENTÐYJ, LIFTGATE GLASS
WEATHERSTRIP SEAL................23-125
REPLACEMENTÐYJ, SIDE MARKER
LAMP BULB.........................8L-25
REPLACEMENTÐYJ, UNDERHOOD LAMP . 8L-29
REPLACEMENTÐYJ, UNDERHOOD LAMP
BULB..............................8L-29
REPLACEMENTÐYJ VEHICLES, DRIVE
AXLE ASSEMBLY; FRONT SUSPENSION
AND AXLE...........................2-24
REPLACEMENTÐYJ VEHICLES, DRIVE
AXLE ASSEMBLY; REAR SUSPENSION
AND AXLES..........................3-14
REPLACEMENTÐYJ VEHICLES,
HARDTOP DOME/CARGO LAMP BULB....8L-31
REQUIREMENTS, FUEL..................0-1
REQUIRING NO LUBRICATION,
COMPONENTS.........................0-2
RESERVE/OVERFLOW SYSTEM,
COOLANT............................7-24
RESERVOIR REPLACEMENT (2-PIECE
MASTER CYLINDER)...................5-19
RESERVOIR, VACUUM.................8H-1
RESISTANCE, IGNITION COIL............8D-9
RESISTANCE (OHMS)ÐCOOLANT
TEMPERATURE SENSOR/MANIFOLD
AIR TEMPERATURE, SENSOR...........14-46
RESISTANCE, SPARK PLUG CABLE......8D-14
RESISTORS REPLACEMENT, BLOWER
MOTOR............................24-31
RESTRAINT REPLACEMENTÐXJ, DOOR . . . 23-41
RETAINER AND PISTON
SPECIFICATIONS, AW-4...............21-340
RETAINING BRACKETÐYJ, REARVIEW
MIRROR..........................23-144
RETURNÐPCM INPUT, SENSOR.........14-25
REVEAL MOLDINGÐXJ, WINDSHIELD....23-66
REVEAL MOLDINGÐYJ, WINDSHIELD . . . 23-144
RHD, STEERING.....................19-74
RIGHT HAND DRIVE, AUTOMATIC BELT
TENSIONERÐXJ MODELS WITH.........7-42
RIGHT HAND DRIVE, BELT SERVICEÐ
EXCEPT.............................7-40
RIGHT HAND DRIVE, BELT SERVICEÐXJ
MODELS WITH.......................7-42
RIGHT HAND DRIVE (RHD), BELT
TENSIONÐEXCEPT....................7-38
RIGHT HAND DRIVE (RHD) MODELS,
BELT TENSIONÐEXCEPT...............7-45
RIGHT HAND DRIVE VEHICLES...........23-1
RIGHT TURN RELAY; TRAILER TOW
(XJ).............................8W-54-1
RIGHT TURN RELAY; TRAILER TOW
(XJ-RHD).........................8W-54-1
RING CHARTÐAX 15 MANUAL
TRANSMISSION, SELECTIVE SNAP......21-334
RING/THRUST WASHER/THRUST PLATE
SPECIFICATIONS, 30RH/32RH SNAP.....21-335
ROCKER ARMS AND PUSH RODS....9-23,9-65
ROD AND PAWL SERVICE, PARK.......21-190
ROD BALL STUD REPLACEMENTÐXJ,
LIFTGATE SUPPORT
..................23-63
ROD BEARING FITTING CHART,
CONNECTING
.....................9-41,9-83
ROD CYLINDER DISPOSALÐXJ,
LIFTGATE SUPPORT
..................23-63
ROD CYLINDERÐXJ, LIFTGATE
SUPPORT
..........................23-62
ROD, TIE
......................19-16,19-19RODS, PISTONS AND CONNECTING . . . 9-39,9-81
RODS, ROCKER ARMS AND PUSH....9-23,9-65
RODSÐXJ, DOOR INSIDE LATCH
RELEASE AND LOCK..................23-50
ROOF VENTÐYJ, HARD TOP..........23-127
ROTOR, DISTRIBUTOR.................8D-8
ROTOR, IGNITION CABLES,
DISTRIBUTOR CAP....................0-20
ROTOR INSTALLATION.................5-51
ROTOR REFINISHING, DISC BRAKE.......5-53
ROTOR REMOVAL.....................5-51
ROTOR RUNOUT, DISC BRAKE...........5-52
ROTOR THICKNESS, DISC BRAKE........5-52
ROTORÐSPEEDOMETER DRIVE GEAR,
SPEED SENSOR.....................21-193
ROUGH AND/OR HAS A MISS, INJECTOR
DIAGNOSISÐVEHICLE RUNS...........14-52
ROUTING SCHEMATICÐ2.5L 4
CYLINDER ENGINE, VACUUM............25-3
ROUTING SCHEMATICÐ4.0L 6
CYLINDER ENGINE, VACUUM............25-3
ROUTING SCHEMATICS, VACUUM HOSE . . . 25-2
ROUTING, SYSTEM COOLANT.............7-1
RUBBER AND PLASTIC COMPONENT
INSPECTION.........................0-20
RUBBER AND PLASTIC HOSES/TUBING....0-26
RUNNING LAMP (DRL) MODULE,
DAYTIME.........................8W-50-2
RUNNING LAMP (DRL) MODULEÐ
CANADIAN VEHICLES ONLY, DAYTIME. . . 8W-50-2
RUNNING LIGHTS (CANADA ONLY)ÐXJ,
DAYTIME...........................8L-15
RUNNING LIGHTS (CANADA ONLY)ÐYJ,
DAYTIME...........................8L-30
RUNOUT............................16-4
RUNOUT, CLUTCH COVER AND DISC.......6-3
RUNOUT, DISC BRAKE ROTOR...........5-52
RUNOUT, FLYWHEEL....................6-3
RUNOUT SPECIFICATIONS..............16-4
RUNOUT, TIRE AND WHEEL.............22-8
RUNS ROUGH AND/OR HAS A MISS,
INJECTOR DIAGNOSISÐVEHICLE........14-52
SAFETY CERTIFICATION LABEL, VEHICLE . Intro.-4
SAFETY LATCH STRIKER
REPLACEMENTÐXJ..................23-11
SAFETY LATCHÐYJ, HOOD............23-109
SAFETY PRECAUTIONS AND WARNINGS . . 13-10
SAFETY PRECAUTIONS, BRAKE...........5-2
SAFETY PRECAUTIONS, CLUTCH.........6-10
SANDING,BUFFING AND POLISHING,
WET..............................23-158
SCAN TOOL, DRB; BRAKES...............5-3
SCAN TOOL, DRB; COOLING SYSTEM......7-5
SCAN TOOL, DRB; EMISSION CONTROL
SYSTEMS...........................25-2
SCAN TOOL, DRB; FUEL SYSTEM........14-54
SCAN TOOL, DRB; IGNITION SYSTEMS....8D-8
SCHEDULES, MAINTENANCE.............0-4
SCHEMATIC - YJ, BUZZER MODULE......8U-4
SCHEMATICÐ2.5L 4 CYLINDER ENGINE,
VACUUM ROUTING....................25-3
SCHEMATICÐ4.0L 6 CYLINDER ENGINE,
VACUUM ROUTING....................25-3
SCHEMATICÐXJ, AIR CONDITIONING.....24-5
SCHEMATICÐXJ, HEATING..............24-2
SCHEMATICS, BELT....................7-38
SCHEMATICS, PCM SYSTEM............14-41
SCHEMATICS, VACUUM HOSE ROUTING . . . 25-2
SCI RECEIVEÐPCM INPUT.............14-24
SCI TRANSMITÐPCM OUTPUT.........14-29
SCREENÐXJ, COWL GRILLE...........23-12
SCREENÐXJ, HEADLAMP/FOG LAMP
ADJUSTMENT USING ALIGNMENT........8L-7
SCREENÐYJ, COWL GRILLE..........23-109
SCREENÐYJ, HEADLAMP/FOG LAMP
ADJUSTMENT USING ALIGNMENT.......8L-23
SCREW ANCHOR AND BUMPERÐXJ,
LIFTGATE LICENSE PLATE..............23-65
SCUFF PLATE/COWL SIDE TRIM
PANELÐXJ, FRONT INNER.............23-86
SCUFF PLATESÐXJ, INTERIOR TRIM
PANELS
............................23-84
SCUFF PLATESÐXJ, OUTER
............23-89
SEAL AND BEARING, AXLE SHAFT
........3-17
SEAL AND BEARING SERVICE, AXLE
SHAFT
..............................3-32
SEAL AND SPRING REPLACEMENT,
VALVE STEM
.........................9-65SEAL REPLACEMENT, INNER AXLE
SHAFT OIL...........................2-35
SEAL REPLACEMENT, MANUAL VALVE
SHAFT............................21-187
SEAL REPLACEMENT, OIL PUMP.......21-199
SEAL REPLACEMENT, PINION; FRONT
SUSPENSION AND AXLE................2-25
SEAL REPLACEMENT, PINION; REAR
SUSPENSION AND AXLES...............3-33
SEAL REPLACEMENT, PINION SHAFT......3-15
SEAL REPLACEMENT, PITMAN SHAFT....19-37
SEAL REPLACEMENT, TIMING CASE
COVER OIL......................9-30,9-73
SEAL REPLACEMENTÐYJ, DOOR
WEATHERSTRIP....................23-142
SEAL REPLACEMENTÐYJ, LIFTGATE
GLASS WEATHERSTRIP..............23-125
SEAL/CROSSMEMBER AIR
DEFLECTORÐXJ, COWL
WEATHERSTRIP.....................23-11
SEALÐDRIVE PLATE SERVICE,
CONVERTERÐPUMP.................21-116
SEALÐXJ, LIFTGATE OPENING
WEATHERSTRIP.....................23-64
SEALÐYJ, BELTLINE.................23-142
SEALÐYJ, COWL WEATHERSTRIP......23-109
SEALÐYJ, TAILGATE WEATHERSTRIP . . . 23-123
SEALÐYJ, WINDSHIELD FRAME
WEATHERSTRIP....................23-146
SEALS AND BEARING REPLACEMENT,
PITMAN SHAFT......................19-34
SEALS, REAR MAIN OIL..............9-49,9-89
SEALS, VALVE SPRINGS AND OIL........9-23
SEALSÐIN CAR REPLACEMENT, PITMAN
SHAFT.............................19-23
SEALSÐXJ, DOOR WINDOW GLASS
AND DOOR OPENING WEATHERSTRIP....23-55
SEALSÐYJ, FULL-METAL DOOR
WEATHERSTRIP....................23-141
SEAT ADJUSTER/MOTORS, POWER . . . 8R-1,8R-2
SEAT ADJUSTER/MOTORS REMOVE/
INSTALL, POWER.....................8R-3
SEAT BELT INDICATOR WARNING LAMP;
INSTRUMENT CLUSTER (XJ).........8W-40-2
SEAT BELT INDICATOR WARNING LAMP;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
SEAT BELT SWITCH, DRIVER'S......8U-1,8U-3
SEAT CUSHION AND COVERÐXJ,
BUCKET............................23-81
SEAT CUSHION COVERÐXJ, REAR......23-82
SEAT CUSHIONÐXJ, REAR.............23-82
SEAT PLATFORMÐXJ, BUCKET.........23-82
SEAT, POWER; POWER SEAT (XJ).....8W-63-1
SEAT, POWER; POWER SEAT (XJ-RHD) . 8W-63-1
SEAT SWITCH CONTINUITY, POWER......8R-2
SEAT SWITCH, POWER............8R-1,8R-2
SEAT SWITCH REMOVE/INSTALL,
POWER.............................8R-3
SEATBACK COVER AND FRAMEÐXJ,
BUCKET............................23-81
SEATBACK COVERÐXJ, REAR..........23-84
SEATBACK LATCH STRIKER AND
BUMPERÐXJ, REAR..................23-84
SEATBACKÐXJ, REAR................23-83
SEATÐYJ, REAR BENCH..............23-153
SEATSÐXJ, FRONT BUCKET............23-81
SEATSÐYJ........................23-153
SEATSÐYJ, BUCKET.................23-153
SECOND (2) RANGE, HYDRAULIC FLOW
IN MANUAL.........................21-96
SECOND BRAKE OVERHAUL...........21-241
SECONDARY CABLES, SPARK PLUG.....8D-14,
8D-24
SECONDARY CIRCUIT DIAGNOSIS,
IGNITION...........................8D-10
SECTION IDENTIFICATION; WIRING
DIAGRAMS (XJ)......................8W-1
SECTION IDENTIFICATION; WIRING
DIAGRAMS (XJ-RHD)..................8W-1
SECTION IDENTIFICATION; WIRING
DIAGRAMS (YJ)
......................8W-1
SELECTIVE SNAP RING CHARTÐAX 15
MANUAL TRANSMISSION
.............21-334
SELF-DIAGNOSTIC TEST, COMPASS/
DISPLAY
............................8C-2
SENDING UNIT, FUEL GAUGE
...........14-16
SENSEÐPCM INPUT, AUTOMATIC
SHUTDOWN (ASD)
...................14-21
24 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

TIRE/WHEEL HOLDDOWN AND FLOOR
BRACKETSÐXJ, SPARE...............23-98
TO USE THIS GROUP, HOW; WIRING
DIAGRAMS (XJ)......................8W-1
TO USE THIS GROUP, HOW; WIRING
DIAGRAMS (XJ-RHD)..................8W-1
TO USE THIS GROUP, HOW; WIRING
DIAGRAMS (YJ)......................8W-1
TOOL, DRB SCAN; BRAKES...............5-3
TOOL, DRB SCAN; COOLING SYSTEM......7-5
TOOL, DRB SCAN; EMISSION CONTROL
SYSTEMS...........................25-2
TOOL, DRB SCAN; FUEL SYSTEM........14-54
TOOL, DRB SCAN; IGNITION SYSTEMS....8D-8
TOOLS, TROUBLESHOOTING............8W-4
TOP DOORÐYJ, HALF-METAL SOFT.....23-134
TOP LIFTGATE GLASSÐYJ, HARD......23-124
TOP QUARTER WINDOW GLASSÐYJ,
HARD.............................23-149
TOP REPAIRÐYJ, HARD..............23-127
TOP ROOF VENTÐYJ, HARD..........23-127
TOP SERVICE INFORMATIONÐYJ, SOFT . 23-127
TOP SERVICEÐYJ, SOFT.............23-129
TOPÐYJ, HARD....................23-126
TORQUE; BATTERY/STARTER/
GENERATOR SERVICE..................8B-8
TORQUE; COOLING SYSTEM.............7-46
TORQUE; FUEL SYSTEM...............14-67
TORQUE; IGNITION SYSTEMS............8D-32
TORQUE CONVERTER...........21-167,21-67
TORQUE CONVERTER CLUTCH RELAY....14-65
TORQUE CONVERTER CLUTCH RELAY
TEST..............................14-48
TORQUE CONVERTER CLUTCH
RELAYÐPCM OUTPUT................14-29
TORQUE CONVERTER CLUTCH (TCC)
SOLENOID AND RELAY; FUEL/IGNITION
(XJ).............................8W-30-4
TORQUE CONVERTER CLUTCH (TCC)
SOLENOID AND RELAY;
TRANSMISSION CONTROLS (YJ)......8W-31-1
TORQUE CONVERTER CLUTCH (TCC)
SOLENOID AND RELAYÐ2.5L ENGINE
ONLY; TRANSMISSION CONTROLS (XJ) . 8W-31-1
TORQUE CONVERTER DIAGNOSIS . . 21-86,21-87,
21-88
TORQUE CONVERTER INSTALLATION,
TRANSMISSION.....................21-199
TORQUE CONVERTER REMOVAL,
TRANSMISSION.....................21-198
TORQUE CONVERTER STALL TEST......21-178
TORQUE CONVERTER STATOR CLUTCH
INSPECTION.......................21-199
TORQUE SPECIFICATIONS; CLUTCH.......6-17
TORQUE SPECIFICATIONS; ENGINES . . 9-54,9-95
TORQUE SPECIFICATIONS; EXHAUST
SYSTEM AND INTAKE MANIFOLD........11-10
TORQUE SPECIFICATIONS; FRONT
SUSPENSION AND AXLE................2-49
TORQUE SPECIFICATIONS; HEATING AND
AIR CONDITIONING...................24-37
TORQUE SPECIFICATIONS;
INTRODUCTION............Intro.-11,Intro.-12
TORQUE SPECIFICATIONS; PROPELLER
SHAFTS............................16-15
TORQUE SPECIFICATIONS; REAR
SUSPENSION AND AXLES...............3-51
TORQUE SPECIFICATIONS; STEERING....19-78
TORQUE SPECIFICATIONS, 30RH/32RH . . 21-336
TORQUE SPECIFICATIONS, AW-4.......21-344
TORQUE SPECIFICATIONS, BRAKE........5-70
TORQUE SPECIFICATIONS,
MEASUREMENT...................Intro.-11
TORQUE SPECIFICATIONS, NP231/NP242 . 21-344
TORQUE SPECIFICATIONSÐ
ACCESSORIES......................23-162
TORQUE SPECIFICATIONSÐMANUAL
TRANSMISSION.....................21-333
TORQUE SPECIFICATIONSÐXJ
VEHICLES.........................23-161
TORQUEÐ2.5L.......................8B-8
TORQUEÐ4.0L.......................8B-8
TOUCH-UP, PAINTED SURFACE.........23-158
TOW HOOK, REAR
.....................13-9
TOW HOOKS
........................13-13
TOW HOOKS, FRONT
..................13-7
TOW, TRAILER; TRAILER TOW (XJ)
....8W-54-1
TOW, TRAILER; TRAILER TOW (XJ-RHD)
. 8W-54-1TOWING AND HOISTING, JUMP
STARTING............................0-9
TOWING, FOUR-WHEEL-DRIVE VEHICLE . . . 0-12
TOWING RECOMMENDATIONS...........0-10
TOWING SPECIFICATIONS, TRAILER....Intro.-5,
Intro.-9
TOWING WHEN KEYS ARE NOT
AVAILABLE..........................0-13
TOWINGÐXJ, TWO-WHEEL-DRIVE
VEHICLE............................0-11
(TPS)ÐPCM INPUT, THROTTLE
POSITION SENSOR...................14-25
TRACK BAR; FRONT SUSPENSION AND
AXLE...........................2-11,2-15
TRACK BAR; REAR SUSPENSION AND
AXLES...............................3-8
TRAC-LOK DIFFERENTIAL...............3-45
TRAILER HITCH......................23-77
TRAILER HITCHÐXJ..................23-77
TRAILER TOW; TRAILER TOW (XJ)....8W-54-1
TRAILER TOW; TRAILER TOW (XJ-RHD) . 8W-54-1
TRAILER TOWING SPECIFICATIONS....Intro.-5,
Intro.-9
TRANSFER CASE (4WD VEHICLES).......0-24
TRANSFER CASE ASSEMBLY....21-294,21-319
TRANSFER CASE CHANGES...........21-307
TRANSFER CASE DISASSEMBLY AND
OVERHAUL..................21-289,21-310
TRANSFER CASE IDENTIFICATION......21-284,
21-307
TRANSFER CASE INSTALLATION . . 21-288,21-309
TRANSFER CASE, LEGEND FOR NP231 . . 21-306
TRANSFER CASE, LEGEND FOR NP242 . . 21-332
TRANSFER CASE LUBRICANT AND FILL
LEVEL............................21-284
TRANSFER CASE, NP231.......21-283,21-305
TRANSFER CASE, NP242.......21-307,21-331
TRANSFER CASE REMOVAL.....21-287,21-309
TRANSFER CASE SKID PLATE.......13-15,13-3
TRANSMISSION, 30RH/32RH
AUTOMATIC.........................21-67
TRANSMISSION AND CONVERTER
INSTALLATION......................21-117
TRANSMISSION AND CONVERTER
REMOVAL.........................21-115
TRANSMISSION AND TORQUE
CONVERTER INSTALLATION...........21-199
TRANSMISSION AND TORQUE
CONVERTER REMOVAL...............21-198
TRANSMISSION APPLICATION..........21-67
TRANSMISSION ASSEMBLY AND
ADJUSTMENT............21-265,21-16,21-52
TRANSMISSION ASSEMBLY AND
ADJUSTMENT PROCEDURES..........21-155
TRANSMISSION ASSEMBLY TIPS.......21-155
TRANSMISSION, AUTOMATIC............0-23
TRANSMISSION, AW-4 AUTOMATIC.....21-165
TRANSMISSION, AX 15 MANUAL........21-33
TRANSMISSION, AX 4/5 MANUAL........21-1
TRANSMISSION CASE CLEANING AND
INSPECTION.......................21-125
TRANSMISSION CASE OVERHAUL,
FIRST-REVERSE BRAKE PISTON........21-247
TRANSMISSION CHANGES AND PARTS
INTERCHANGEABILITY................21-67
TRANSMISSION COMFORT SWITCH;
TRANSMISSION CONTROLS (XJ-RHD) . . 8W-31-1
TRANSMISSION CONTROL MODULE;
TRANSMISSION CONTROLS (XJ-RHD) . . 8W-31-1
TRANSMISSION CONTROL MODULE
(TCM) SERVICE.....................21-183
TRANSMISSION CONTROL MODULEÐ
4.0L ENGINE ONLY; TRANSMISSION
CONTROLS (XJ)...................8W-31-1
TRANSMISSION CONTROLS AND
COMPONENTS.......................21-67
TRANSMISSION COOLER FLOW TESTING . 21-113
TRANSMISSION COOLER LINE AND
FITTING SERVICE...................21-111
TRANSMISSION COOLER LINE FITTINGS . 21-197
TRANSMISSION COOLER REVERSE
FLUSHING.........................21-114
TRANSMISSION COOLER SERVICE
......21-196
TRANSMISSION DIAGNOSIS
. 21-78,21-79,21-80,
21-81,21-82,21-83,21-84,21-85
TRANSMISSION DIAGNOSIS, 30RH/32RH
. 21-70
TRANSMISSION DIAGNOSIS, AW-4
.....21-176
TRANSMISSION DISASSEMBLY
. . 21-119,21-201TRANSMISSION DISASSEMBLY AND
OVERHAUL.....................21-37,21-5
TRANSMISSION GEAR RATIOS..........21-34
TRANSMISSION IDENTIFICATION . . 21-166,21-33,
21-67,21-2
TRANSMISSION INSTALLATION.....21-36,21-5
TRANSMISSION LUBRICANT............21-34
TRANSMISSION, MANUAL..............0-22
TRANSMISSION OIL COOLERS...........7-36
TRANSMISSION OVERHAUL, 30RH/32RH . 21-119
TRANSMISSION OVERHAUL, AW-4......21-201
TRANSMISSION RANGE LAMP;
INTERIOR LIGHTING (YJ)............8W-44-1
TRANSMISSION RANGES AND SHIFT
LEVER POSITIONS...................21-166
TRANSMISSION REMOVAL.........21-35,21-3
TRANSMISSION REMOVAL AND
INSTALLATION, 30RH/32RH...........21-115
TRANSMISSION REMOVAL AND
INSTALLATION, AW-4................21-198
TRANSMISSION SHIFT PATTERN........21-34
TRANSMISSION SHIFTER/IGNITION
INTERLOCK MECHANISM, AUTOMATIC....19-55
TRANSMISSION SWITCH AND PLUG
LOCATIONS.........................21-34
TRANSMISSION THROTTLE CABLE
ADJUSTMENT......................21-194
TRANSMISSION THROTTLE CABLE
REPLACEMENT.....................21-193
TRANSMISSION THROTTLE VALVE
CABLE ADJUSTMENT...................21-71
TRANSMISSION, TORQUE
SPECIFICATIONSÐMANUAL...........21-333
TRANSMISSION UP-SHIFT LAMP,
MANUAL; INSTRUMENT CLUSTER (XJ) . 8W-40-2
TRANSMISSION VALVE BODY
INSTALLATION......................21-187
TRANSMISSION VALVE BODY
OVERHAUL........................21-250
TRANSMISSION VALVE BODY REMOVAL . 21-186
TRANSMISSION VALVE BODY
SOLENOIDS........................21-184
TRANSMISSION/TRANSFER CASE
IDENTIFICATION, ENGINE.............Intro.-5
TRANSMISSION/TRANSFER CASE
SPECIFICATIONS....................21-333
TRANSMITÐPCM OUTPUT, SCI.........14-29
TRANSMITTER, KEYLESS ENTRY . 8P-1,8P-7,8P-8
TRAVEL SENSOR, BRAKE PEDAL;
ANTI-LOCK BRAKES (YJ)............8W-32-1
TRAY LAMPÐXJ, I/P ASH RECEIVER.....23-80
TRAYÐXJ, BATTERY
..................23-14
TRAYÐYJ, BATTERY
.................23-110
TREAD WEAR INDICATORS
..............22-3
TRIM COVERSÐXJ, B/C-PILLAR AND
LIFTGATE PILLAR
....................23-88
TRIM PANEL EXTENSIONÐXJ, QUARTER
. 23-87
TRIM PANELÐXJ, DOOR
..............23-31
TRIM PANELÐXJ, FRONT INNER SCUFF
PLATE/COWL SIDE
...................23-86
TRIM PANELÐXJ, LIFTGATE
............23-59
TRIM PANELÐYJ, FULL-METAL DOOR
. . . 23-137
TRIM PANELS AND SCUFF PLATESÐXJ,
INTERIOR
..........................23-84
TRIM PANELSÐXJ, QUARTER AND
WHEELHOUSE
.......................23-87
TRIM REPAIR PRODUCTSÐXJ,
AFTERMARKET PAINT
................23-159
TRIM REPAIR PRODUCTSÐYJ,
AFTERMARKET PAINT
................23-160
TROUBLE CODE (DTC), DIAGNOSTIC
.....14-54
TROUBLE CODE, GENERATOR
DIAGNOSTIC
........................8A-22
TROUBLE CODE, SPEED CONTROL
DIAGNOSTIC
.........................8H-5
TROUBLE DIAGNOSISÐXJ, DOME/
COURTESY LAMP
....................8L-16
TROUBLE DIAGNOSISÐXJ, HEADLAMP
DELAY FUNCTION
....................8L-14
TROUBLE DIAGNOSISÐXJ, LIGHTED
VANITY MIRROR
.....................8L-16
TROUBLE DIAGNOSISÐYJ, DOME/
COURTESY LAMP
....................8L-31
TROUBLESHOOTING TESTS; WIRING
DIAGRAMSÐGENERAL INFORMATION
(XJ)
...............................8W-4
30 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

TROUBLESHOOTING TOOLS; WIRING
DIAGRAMSÐGENERAL INFORMATION
(XJ)...............................8W-4
TROUBLESHOOTING WIRING
PROBLEMS; WIRING DIAGRAMSÐ
GENERAL INFORMATION (XJ)...........8W-5
TUBE AXLE (2WD), MODEL 30 AXLE......2-22
TUBE CAP, FUEL TANK FILLER;
EMISSION CONTROL SYSTEMS......25-4,25-7
TUBE CAP, FUEL TANK FILLER; FUEL
SYSTEM............................14-13
TUBE, NO-LEAD FUEL TANK FILLER......14-13
TUBES/LINES/HOSES AND CLAMPS,
FUEL..........................14-62,14-9
TURN RELAY, LEFT; TRAILER TOW (XJ) . 8W-54-1
TURN RELAY, LEFT; TRAILER TOW
(XJ-RHD).........................8W-54-1
TURN RELAY, RIGHT; TRAILER TOW
(XJ).............................8W-54-1
TURN RELAY, RIGHT; TRAILER TOW
(XJ-RHD).........................8W-54-1
TURN SIGNAL INDICATOR LAMPS;
INSTRUMENT CLUSTER (XJ).........8W-40-2
TURN SIGNAL INDICATOR LAMPS;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
TURN SIGNAL RELAY; TURN SIGNALS
(XJ-RHD).........................8W-52-1
TURN SIGNAL SYSTEM.................8J-1
TURN SIGNAL SYSTEM - YJ.............8J-3
TURN SIGNAL/HAZARD WARNING
SWITCH REMOVE/INSTALL - YJ..........8J-5
TURN SIGNAL/HAZARD WARNING
SYSTEM - XJ..........................8J-3
TURN SIGNALS; TURN SIGNALS (YJ) . . 8W-52-1
TURN SIGNAL/TAIL LAMP BULB
REPLACEMENTÐXJ, BACK-UP/REAR.....8L-12
TURN SIGNAL/TAIL LAMP BULB
REPLACEMENTÐYJ, BACK-UP/REAR.....8L-28
TWO-WHEEL-DRIVE VEHICLE TOWINGÐ
XJ .................................0-11
U-JOINTS, PROPELLER SHAFTS.........16-15
UNBALANCE.........................16-3
UNDERHOOD LAMP; INTERIOR
LIGHTING (XJ)....................8W-44-2
UNDERHOOD LAMP; INTERIOR
LIGHTING (XJ-RHD)................8W-44-1
UNDERHOOD LAMP; INTERIOR
LIGHTING (YJ)....................8W-44-1
UNDERHOOD LAMP BULB
REPLACEMENTÐXJ..................8L-13
UNDERHOOD LAMP BULB
REPLACEMENTÐYJ..................8L-29
UNDERHOOD LAMP REPLACEMENTÐXJ . . 8L-13
UNDERHOOD LAMP REPLACEMENTÐYJ . . 8L-29
UNDERHOOD LAMP SERVICE
INFORMATIONÐXJ...................8L-12
UNDERHOOD LAMP SERVICE
INFORMATIONÐYJ...................8L-28
UNIT (ECU), ELECTRONIC CONTROL......5-34
UNIT, FUEL GAUGE SENDING...........14-16
UNIT (HCU), HYDRAULIC CONTROL.......5-33
UNIT, HYDRAULIC CONTROL; ANTI-LOCK
BRAKES (XJ)......................8W-32-2
UNIT, HYDRAULIC CONTROL; ANTI-LOCK
BRAKES (XJ-RHD).................8W-32-2
UNIT, HYDRAULIC CONTROL; ANTI-LOCK
BRAKES (YJ)......................8W-32-2
UNIVERSAL JOINT ANGLE
MEASUREMENT.......................16-4
UNIVERSAL JOINT REPLACEMENT.......16-10
UNIVERSAL JOINTS...................16-2
UNLOCK RELAY; POWER DOOR LOCKS
(XJ).............................8W-61-1
UNLOCK RELAY; POWER DOOR LOCKS
(XJ-RHD).........................8W-61-1
UPPER SUSPENSION ARM..............2-12
UPSHIFT LAMP; FUEL/IGNITION (XJ) . . . 8W-30-5
UP-SHIFT LAMP; INSTRUMENT CLUSTER
(YJ)
.............................8W-40-2
UPSHIFT LAMP; TRANSMISSION
CONTROLS (XJ)
...................8W-31-1
UPSHIFT LAMP; TRANSMISSION
CONTROLS (YJ)
...................8W-31-1
UP-SHIFT LAMP, MANUAL
TRANSMISSION; INSTRUMENT
CLUSTER (XJ)
.....................8W-40-2
USAGE, INSTALLATION METHODS AND
PARTS
...............................6-4USAGE STATEMENT, FUEL...............14-1
USAGE STATEMENTÐGAS ENGINES,
FUEL...............................0-19
USE THIS GROUP, HOW TO; WIRING
DIAGRAMS (XJ)......................8W-1
USE THIS GROUP, HOW TO; WIRING
DIAGRAMS (XJ-RHD)..................8W-1
USE THIS GROUP, HOW TO; WIRING
DIAGRAMS (YJ)......................8W-1
USING ALIGNMENT SCREENÐXJ,
HEADLAMP/FOG LAMP ADJUSTMENT.....8L-7
USING ALIGNMENT SCREENÐYJ,
HEADLAMP/FOG LAMP ADJUSTMENT....8L-23
USING ON-BOARD DIAGNOSTIC
SYSTEM; BATTERY/STARTING/
CHARGING SYSTEMS DIAGNOSTICS.....8A-22
USING ON-BOARD DIAGNOSTIC
SYSTEM; VEHICLE SPEED CONTROL
SYSTEM............................8H-5
VACUUM DISCONNECT AXLEÐYJ
VEHICLES...........................2-27
VACUUM HOSE ROUTING SCHEMATICS....25-2
VACUUM MOTOR, FRESH AIR DOOR.....24-34
VACUUM MOTOR REPLACEMENT, A/C
RECIRCULATING DOOR................24-27
VACUUM MOTOR REPLACEMENT,
HEATER/DEFROSTER/INSTRUMENT
PANEL OUTLET......................24-26
VACUUM RESERVOIR..................8H-1
VACUUM RESERVOIR REMOVE/INSTALL . . 8H-10
VACUUM ROUTING SCHEMATICÐ2.5L 4
CYLINDER ENGINE....................25-3
VACUUM ROUTING SCHEMATICÐ4.0L 6
CYLINDER ENGINE....................25-3
VACUUM SUPPLY TEST................8H-6
VACUUM TEST, POWER BOOSTER.........5-9
VALUES, CONVERSION FORMULAS AND
EQUIVALENT......................Intro.-11
VALVE AND SPRING IDENTIFICATION,
AW-4 .............................21-343
VALVE BODY ASSEMBLY AND
ADJUSTMENT......................21-153
VALVE BODY CHECK BALL DIMENSIONS,
AW-4 .............................21-341
VALVE BODY DISASSEMBLY AND
INSPECTION.......................21-147
VALVE BODY INSTALLATION,
TRANSMISSION.....................21-187
VALVE BODY OVERHAUL,
TRANSMISSION.....................21-250
VALVE BODY REMOVAL, TRANSMISSION . 21-186
VALVE BODY SERVICE...............21-104
VALVE BODY SOLENOIDS,
TRANSMISSION.....................21-184
VALVE CABLE ADJUSTMENT,
TRANSMISSION THROTTLE............21-71
VALVE CABLE ADJUSTMENT (XJ/YJ),
THROTTLE.........................21-101
VALVE COMPONENT REPLACEÐ
CYLINDER HEAD NOT REMOVED.....9-23,9-65
VALVE, EXPANSION..............24-31,24-35
VALVE FITTING O-RING SEAL, FLOW
CONTROL..........................19-14
VALVE, FUEL TANK PRESSURE
RELIEF/ROLLOVER..............14-16,14-62
VALVE INSTALLATION (WITH ABS),
MASTER CYLINDER AND
COMBINATION........................5-20
VALVE, MASTER CYLINDERÐ
COMBINATION
........................5-15
VALVE, PRESSURE RELIEF/ROLLOVER
. 25-6,25-7
VALVE REMOVAL (WITH ABS), MASTER
CYLINDER AND COMBINATION
...........5-17
VALVE REPLACEMENT (NON-ABS),
COMBINATION
........................5-16
VALVE SERVICE, CONVERTER
DRAINBACK CHECK
..................21-113
VALVE SHAFT OVERHAUL, MANUAL
.....21-215
VALVE SHAFT SEAL REPLACEMENT,
MANUAL
..........................21-187
VALVE SPRINGS AND OIL SEALS
.........9-23
VALVE SPRINGS, VALVES
...........9-27,9-69
VALVE STEM SEAL AND SPRING
REPLACEMENT
.......................9-65
VALVE TEST, POWER BOOSTER CHECK
.....5-9
VALVE TIMING
....................9-30,9-71
VALVES AND VALVE SPRINGS
.......9-27,9-69VANITY MIRROR LAMPS, VISOR;
INTERIOR LIGHTING (XJ)............8W-44-2
VANITY MIRROR LAMPS, VISOR;
INTERIOR LIGHTING (XJ-RHD)........8W-44-1
VANITY MIRROR TROUBLE
DIAGNOSISÐXJ, LIGHTED.............8L-16
VANITY MIRRORÐXJ, LIGHTED.........8L-16
VARIANCE, PINION GEAR DEPTH; FRONT
SUSPENSION AND AXLE................2-40
VARIANCE, PINION GEAR DEPTH; REAR
SUSPENSION AND AXLES...........3-22,3-39
VARIATION ADJUSTMENT, COMPASS......8C-5
VARIATION, DISC BRAKE ROTOR
THICKNESS..........................5-52
VEHICLE CODE DECODING............Intro.-5
VEHICLE CODE DESIGNATIONS........Intro.-1
VEHICLE CODE PLATE...............Intro.-4
VEHICLE CONTROL AND DISPLAY
SYMBOLS........................Intro.-10
VEHICLE CONTROL AND DISPLAY
SYMBOLS, INTERNATIONAL...........Intro.-5
VEHICLE DESIGNATIONS.............Intro.-1
VEHICLE DIMENSION DATA.....Intro.-5,Intro.-6
VEHICLE EMISSION CONTROL
INFORMATION (VECI) LABEL............25-1
VEHICLE, GEAR ADJUSTMENTS IN.......19-39
VEHICLE IDENTIFICATION NUMBER (VIN)
DECODING........................Intro.-4
VEHICLE IDENTIFICATION NUMBER (VIN)
PLATE ............................Intro.-4
VEHICLE, LABELS AND PLATESÐXJ......Intro.-2
VEHICLE, LABELS AND PLATESÐYJ....Intro.-3
VEHICLE LOAD DATA................Intro.-5
VEHICLE LOAD DATAÐXJ............Intro.-7
VEHICLE LOAD DATAÐYJ............Intro.-8
VEHICLE SAFETY CERTIFICATION LABEL . Intro.-4
VEHICLE SPEED CONTROL; VEHICLE
SPEED CONTROL (XJ)..............8W-33-1
VEHICLE SPEED CONTROL; VEHICLE
SPEED CONTROL (XJ-RHD)..........8W-33-1
VEHICLE SPEED SENSOR; FUEL SYSTEM . . 14-66
VEHICLE SPEED SENSOR; FUEL/
IGNITION (XJ).....................8W-30-2
VEHICLE SPEED SENSOR; FUEL/
IGNITION (YJ).....................8W-30-3
VEHICLE SPEED SENSOR; VEHICLE
SPEED CONTROL SYSTEM..........8H-1,8H-5
VEHICLE SPEED SENSOR; FUEL/
IGNITION (XJ-RHD)................8W-30-2
VEHICLE SPEED SENSOR TEST.........14-48
VEHICLE SPEED SENSORÐPCM INPUT . . . 14-25
VEHICLE TOWING, FOUR-WHEEL-DRIVE . . . 0-12
VEHICLE TOWINGÐXJ, TWO-WHEEL-
DRIVE..............................0-11
VEHICLE VIBRATION..................22-10
VENT DOOR CONTROL CABLES.........24-32
VENT WINDOW GLASSÐXJ, REAR
QUARTER..........................23-73
VENT WINDOW GLASSÐYJ, FULL-
METAL DOOR......................23-137
VENTILATION SYSTEM, CRANKCASE;
EMISSION CONTROL SYSTEMS..........25-5
VENTILATION SYSTEM, CRANKCASE;
LUBRICATION AND MAINTENANCE........0-19
VENTÐYJ, HARD TOP ROOF..........23-127
VIBRATION; FRONT SUSPENSION AND
AXLE...............................2-19
VIBRATION; PROPELLER SHAFTS.........16-3
VIBRATION; REAR SUSPENSION AND
AXLES..............................3-10
VIBRATION DAMPER...............9-30,9-72
VIBRATION DIAGNOSIS
...........22-10,22-11
VIBRATION, DRIVELINE
.................16-3
VIBRATION, TIRE NOISE OR
.............22-4
VIBRATION TYPES
....................22-10
VIBRATION, VEHICLE
.................22-10
VISCOUS FAN DRIVE
...................7-34
VISOR VANITY MIRROR LAMPS;
INTERIOR LIGHTING (XJ)
............8W-44-2
VISOR VANITY MIRROR LAMPS;
INTERIOR LIGHTING (XJ-RHD)
........8W-44-1
VISUAL INSPECTION
..................14-35
VOLTAGE, OPEN CIRCUIT
...............8A-6
VOLTAGE SPECIFICATIONS, OUTPUT
.....8A-23
VOLTAGEÐPCM INPUT, BATTERY
........14-21
WARNING LAMP, ABS; ANTI-LOCK
BRAKES (XJ)
......................8W-32-2
JINDEX 31
Description Group-Page Description Group-Page Description Group-Page