air bleeding JEEP CJ 1953 Service Manual

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P The
standard parking brakes (Fig. P-3) consist of
cable-controlled linkage for applying the rear wheel

brake
shoes
mechanically. A single cable from the

parking
brake control lever is connected, by means of an equalizer, to cables leading to individual rear

brakes.
A lever attached to the secondary
shoe,

with a link acting against the
primary
shoe,
expands the
shoes
into
contact with the drums.
P-4.
Transmission Brake

The
transmission brake is mechanically operated
by a hand lever through a cable and conduit and is mounted at the rear output bearing housing on the
transfer case. The transmission brake and its
linkage are shown in Fig. P-4.
P-5.
Brake Maintenance
No brake can be
expected
to work well when grease
or oil is allowed to leak
into
the drum from the rear axle. Little braking friction can be obtained

between
brakes and drums when the surface is
covered with grease and oil. For this reason, take
care
not to over-lubricate wheel bearings, forcing

lubricant
past seals. Also, check condition of seals

if
leak is suspected or whenever brake drums

are
pulled.
Whenever
wheels
are removed, it is advisable to
wash the drums with a suitable solvent so that all
grease and dirt are removed. Linings with any
evidence of grease or oil on them should be replaced.
The
hydraulic system should be kept free of dirt

and
moisture.
Use only SAE standard J-1703 Hydraulic
Brake
Fluid.

Caution:
Keep mineral oils, gasoline, or kerosene
out of the system as
they
cause rubber cups to

soften,
swell, and distort, resulting in failure.
P-6.
Brake
Service

To
service the brakes,
follow
the procedure
below:

a.
Check the fluid level in the brake master cylin­
der.
See Lubrication Section, Par. B-40.
b. Check brake pedal adjustment. See Par. P-9.
c. Check brake pedal travel. If the pedal travels more than halfway to the floor, the brake system
must be checked and the self adjusting star wheel mechanisms checked for binding, also the brake
linings should be inspected as
they
may be badly

worn.
How much lining is
left
can only be deter­ mined by visually inspecting the linings. See Par.
P-l6 for relining brakes.

d.
If the brakes pull to one side after adjustment, check tire pressures. All tires must be inflated to recommended pressures to ensure even braking. If
the condition persists, examine the brake linings
for foreign material and clean as necessary. If clean­
ing
does
not correct the condition the linings should be replaced. If the side pull persists, check front
wheel alignment and balance.
e. Check the brake system for leaks by applying a steady pressure on the brake pedal. A leak in the
system
will
allow the pedal to "fall away". If the pedal "falls away" check for a leaking wheel cylin­
der.
Remove
wheels
and drums and carefully check
each cylinder. Also examine all lines and fittings.

Rebuild
or replace all wheel cylinders (Par. P-21)

if
one is
defective
as
they
are all probably in poor condition. If the leak has allowed brake fluid to get
on the linings, the linings
will
have to be replaced.
f. A
"spongy"
brake pedal indicates the pressure of air in the hydraulic system.
This
condition must
be corrected by bleeding the brakes. See Par. P-7.
g. Should the brakes
become
locked so that the vehicle cannot be moved, the brakes may be re­
leased by opening the bleeder screw on any one of the wheel cylinders. Before the vehicle is driven, correct the cause of the condition. The cause may
3
14 15 16 17 18
4
10796

1—
Cable
and Conduit
2—
Hand
Brake
Clip

3—
Hand
Brake
Bracket
4—
Hand
Brake
Handle Assembly 5—
Rear
Cap
6—
Drive
Gear
Bushing
7—
Driven
Gear

8—
Driven
Gear
Sleeve
FIG.
P-4—TRANSMISSION
BRAKE

9—Backing
Plate
10— Shoe and
Lining

11—
Lever
End Return Spring
12—
Brake
Drum
13— Bolt 14—
Rear
Companion Flange
15—
Washer

16— Nut 17— Propeller Shaft Flange Yoke
18—
Rear
Propeller Shaft
19—
Adjusting
End Spring
20—
Adjusting
Screw Bracket
21—
Operating
Lever

22—
Clevis

23—
Retracting
Spring
Clip

24—
Retracting
Spring
Link
325

p

BRAKES
be either a defective master cylinder or the use of
low grade brake fluid which has expanded because
of heat. Use standard duty brake fluid conforming to
SAE-J1703
specification.

P-7.
Bleeding
Brakes

The
hydraulic
brake system must be bled whenever

a
fluid line has been disconnected or air
gets
into the system. A leak in the system may sometimes
be indicated by the presence of a spongy brake
pedal.
Air trapped in the system is compressible

and
does
not permit the pressure, applied to the
brake
pedal, to be transmitted solidly through to
the brakes. The system must be absolutely free
from
air at all times. When bleeding brakes, bleed
at that wheel with the
longest
line from the master
FIG.
P-5—BLEEDING
BRAKES

1—Bleeder
Screw
cylinder
first, the next
longest
second, etc. During
the bleeding operation the master cylinder must
be kept at least %
full
of hydraulic brake fluid.

To
bleed the brakes, first carefully clean all
dirt

from
around the master cylinder filler plug. If
bleeder tank is used follow the manufacturers in­
structions.
Remove the filler plug and
fill
the master
cylinder
to the lower
edge
of filler neck.
Clean
off

all
bleeder connections at all four wheel cylinders.

Attach
bleeder
hose
and fixture to right
rear
wheel

cylinder
bleeder screw and place end of tube in a
glass jar, and submerged in brake fluid. Open the bleeder valve one-half to three-quarters of a
turn.

See
Fig.
P-5.
Depress the
foot
pedal, allowing it to return very
slowly. Continue this pumping action to force the
fluid
through the line and out of the bleeder
hose
which
carries with it any air in the system. When bubbles cease to appear at the end of the bleeder
hose, close the bleeder valve and remove the hose.
After
the bleeding operation at each wheel cylinder
has been completed,
fill
the master cylinder reser­
voir
and replace the filler plug.
Do not re-use the liquid which has been removed

from
the lines through the bleeding process because
of air bubbles and
dirt.

P-8.
Brake Hoses

a.
Hydraulic
lines (tubing and hose) are the means
of transmitting fluid under pressure between the master cylinder and the wheel cylinders.

Note:
On
some
vehicles a proportioning valve is
located in the
rear
brake line along the inside left
frame
side
rail.
The valve is not serviceable and
must be replaced as an assembly.

Should
replacement be necessary make certain the valve is properly positioned with the centerline of
the hex plug (in the bottom of the valve) in the
vertical
position. Refer to Fig. P-l.

The
hoses
are the flexible links between the wheels

or
axles and the frame or body. The
hoses
must

withstand
the fluid pressures without expansion
and
must be free to flex during spring deflection
and
wheel turns without causing damage to the
hose.

b.
Hydraulic
lines are subject to damage and
deterioration. Hoses should be inspected for cuts,

chafing,
cracks,
twists and
loose
frame supports.

Hydraulic
tubing should be inspected for signs of
leakage (due to faulty flares or
loose
connections);

restrictions
(due to dents or corrosion); and wear (due to friction against other metal parts). Always
use correct type and size of wrench on fittings.

Avoid
damage to female fittings by supporting fit­
ting with tube nut during removal of assembly.

c.
On fittings where gaskets are used, always use
a
new gasket. Copper gaskets take a set and may
not form a
good
seal if reused.

d.
When replacing hydraulic brake hose, attach
hose
to wheel cylinder and securely tighten hose,
then attach
opposite
end to frame fitting or tubing.
Avoid
twists in
hose
when assembling to frame fitting
or
tubing. Hold
hose
end securely with

wrench
while attaching tubing to hose. If
hose
end
clip
is used, make certain clip is assembled properly.

Check
for interference during spring deflection or
rebound and during front wheel turns.

e.
Check
for any possible contact between front

brake
hose
and inner sidewall of tire when the front
wheels are in maximum
turn
position.
Check
for sufficient but not excessive length of
hose
between
the clamp and the wheels by turning the wheels
from
one extreme
turn
position to the otherl
f.
Check
that there is no possibility of any contact between the
tail
pipe and
rear
brake
hose
under
all
operating conditions.
P-9.
Brake Pedal Adjustment

There
should always be at least W [12,7 mm.]
free pedal travel before the push rod
engages
the master cylinder piston.

This
adjustment is accomplished by shortening or 326

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P h.
Install
the tube seats, flat side toward the check

valve,
and press in with tube nuts or the master

cylinder
brake pipe tube nuts.

BLEEDING
a.
Before the master cylinder is installed on the
car,
the unit must be bled.

b.
Support the cylinder assembly in a vise and

fill
both fluid reservoirs with approved brake fluid,

e.
Loosely install a plug in each
outlet
of the

cylinder.
Depress the push rod several times until

air
bubbles cease to appear in the brake fluid.

d.
Tighten the plugs and attempt to depress the piston. The piston travel should be restricted after
all
air is expelled.
e.
Install
the master cylinder on the car and bleed
the hydraulic lines at the wheel cylinder. Refer to
Par.
P-7.

P-21.
Wheel
Cylinder
Reconditioning
•
Refer to Fig. P-15.
Note:
Make sure a replacement brake cylinder
has the same part number as the original cylinder.

FIG.
P-15—WHEEL
BRAKE CYLINDER
1— Boot

2—
Piston

3—
Cylinder
Cup
4—
Cup
Spring
5—
Cylinder

6—
Bleeder
Screw
a.
To remove a wheel cylinder,
jack
up the vehicle

and
remove the wheel, hub, and
drum.
Disconnect
the brake line at the fitting on the brake backing
plate. Remove the brake
shoe
return spring which

will
allow the brake
shoes
at the toe to
fall
clear of the brake cylinder. Remove two screws holding
the wheel cylinder to the backing plate.
b.
Remove the rubber dust covers on ends of

cylinder.
Remove the pistons and piston cups and
the spring.

c.
Wash the parts in clean alcohol.

d.
Examine the cylinder bore for roughness or
scoring.
Check
fit of pistons to cylinder bore.
e. When reassembling the cylinder, dip springs, pistons and piston cups in brake fluid.
Install

spring
in center of the wheel cylinder.
Install

piston cups with the cupped surface towards the

spring
so that the flat surface
will
be against
the piston.
Install
pistons and dust covers.
f.
Install
wheel cylinder to the backing plate and connect brake line and install brake
shoe
return

spring.

g. Replace wheel, hub, and
drum.

h.
Bleed the brake lines (Par. P-7).

P-22. TROUBLE
SHOOTING

P-23.
Squeaky
Brakes

In
most cases, squeaks are entirely eliminated by

correct
adjustment of the brakes. Squeaks may be
caused however, by glazed linings, lining wore thin
to the point of
exposed
rivets or by vibration. A

drum
will
not vibrate when the brake is securing

uniform
contact over the entire lining surface, ex­
cept when due to improper conditions such as the
linings becoming glazed.
Glazed
surface of the

brake
linings may be removed by a stiff
wire
brush.
Occasionally
squeaks are caused by roughened
sur­

face of the
drum,
which can usually be remedied
by rubbing down with emery cloth and by wiping
the brakings surface clean. In extreme cases it may
be necessary to reface the drum in a lathe. Should
this be done, do not remove a metal thickness greater than .030" [0,762 mm.] - .060" [1,52 mm.]

overall
diameter.

P-24. Rattles
in
Brakes

See that the tension of the springs in the brakes

and
attached to the control system are sufficient to

return
brakes and brake mechanism to their normal
position.
Return
springs are so placed that they
keep all slack out of the control system by tension on all joints.

Brakes
will
not rattle inside the
drum
if the springs
holding the
shoes
are kept at the proper tension. 333

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

ALPHABETICAL INDEX

SUBJECT PAR.
SUBJECT
PAR.

Abbreviations,
List
U-17 Accelerator Linkage E-70
Air
Cleaner B-25, B-26, B-82, C-21, E-69

Air
Delivery Manifold Fl-4, F2-12
Air
Filter, Pump • F2-3, F2-11

Air
Injection Tubes Fl-5, F2-13
Air
Pump Fl-2, F2-10
Alternator Bearings B-76, H-80
Alternator Brushes H-74, H-75
Alternator Charging System •
•
H-63
Alternator
Diodes
H-69, H-85
Alternator Precautions H-64 Alternator Rotor H-76, H-79
Alternator Tests H-67, H-77 Alternator Specifications H-l 52
Alternator Stator H-84
Anti-Backfire
Valve Fl-6, F2-14
Antifreeze
Chart
• G-22 Antifreeze
Solutions
- G-16
Axle Camber O-l
Axle Caster 0-8

Back-Up
Lights H-135

Ballast
Resistor. H-32 Battery C-3, H-2 Bendix Folo-Thru Drive H-105, H-106
Bleeding Brakes P-7
Body T-l Body Lubrication. B-65 Body Name Plates ' A-7

Brake
Adjustment P-14
Brake
Drums. • .P-17

Brake
Hoses
P-8

Brake
Maintenance . P-5
Brake
Master Cylinder B-40, P-2, P-20

Brake
Service P-6
Brake
Wheel Cylinder • P-21

Camber
Adjustment 0-7
Camshaft D-6, D-51, D-52, D-53, D-81, Dl-26, Dl-33, Dl-55, Dl-80

Carburetor
E-10, E-25

Carburetor
Adjustment C-25, E-14, E-40,
Fl-13,
F2-16
Carburetor
Specifications .Fl-38, F2-34, E-79

Caster
Adjustment 0-8

Charging
System Service. .H-34, H-63

Chassis
Lubrication B-7, B-83

Chassis
Torque Specifications U-14

Clutch
1-4, MO
Clutch
Adjustment 1-3
Clutch
Linkage B-44, 1-3

Clutch
Maintenance .. 1-2
Clutch
Release Bearing B-74, 1-25

Coil
C-20, H-19, H-31 Connecting Rod Bearings D-47, D-48, D-49, Dl-49 Connecting Rod
Crank
Pins D-42
Connecting Rods... .D-20, D-50, D-95, Dl-31, Dl-45, Dl-75
Controls B-59, B-62
Cooling System B-28, G-l Cooling System Filling G-2

Core
Hole Expansion Plugs D-72

Crankcase
Ventilating System B-13, C-6, D-110

Crankshaft
D-26, D-38, D-39, Dl-38, Dl-73
Crankshaft
End Play. D-83, Dl-74

Crankshaft
Main Bearing D-43, D-44, Dl-32, Dl-40, Dl-73

Crankshaft
Oil Seal, Front Dl-21, Dl-85
Crankshaft
Oil Seal, Rear D-63, D-85, Dl-72

Cylinder
Block D-32, Dl-34

Cylinder
Bores D-35, Dl-36

Cylinder
Head D-17, D-73, D-98, Dl-24, Dl-63, Dl-82

Cylinder
Head Torque. C-5
Dash Pot Adjustment C-26, E-44
Differential B-51 thru B-53, N-9 Differential Adjustments N-16, N-18
Differential, Powr-Lok N-20
Differential,
Trac-Lok
N-24
Directional Signal Lights. . H-138
Distributor B-14, B-15, C-10, D-13, Dl-9, H-9, H-20 Distributor Check H-l7, H-28
Distributor Point Dwell C-17 Distributor Resistance Test C-16

Drawbar
.R-6, U-16
Dual
Brake System P-l thru P-26

Electrical
Instruments H-l22

Electrical
Specifications .H-l52

Electrical
System H-l Engine .
..D-l,
Dl-1
Engine Code Number A-6
Engine Compression .
.
C-9 Engine Disassembly . • .D-6, Dl-5 Engine Installation D-105, Dl-102
Engine Lubrication System B-4, B-6 Engine Mountings D-3, Dl-3
Engine Oil B-9
Engine Oil Filter B-10, B-ll,
D-lll,
Dl-13, Dl-93
Engine Oil Pan D-l9, D-66, D-97, Dl-29, Dl-51, Dl-77 Engine Oil Pump. . .D-14, D-65, D-93, Dl-19, Dl-50, Dl-87
Engine Overheating. G-l9 Engine Removal D-5, Dl-4.

Exhaust
Emission Control — F4 Fl-1 thru Fl-30
Exhaust
Emission Control — V6 F2-1 thru F2-36
Exhaust
Manifold, Install F-6

Exhaust
Pipe -
•
F-8

Exhaust
System F-2, F-3

Exhaust
System Maintenance F-4

Fan
Belt C-27, Dl-11, Dl-96, G-18
Floating Oil Intake. D-64, Dl-30, Dl-50, Dl-76 Flywheel D-25, D-67, D-87, Dl-28, Dl-52, Dl-78
Flywheel Housing. D-71, D-88, Dl-27, Dl-54, Dl-79
Flywheel Pilot Bushing D-70, 1-8

Frame
R-l

Frame
Alignment. R-2
Frame
Dimensions R-3
Frame
Straightening R-4

Front
Bumper Weight. • U-9
Front
Axle B-50, M-2

Front
Axle Alignment R-5

Front
Axle Installation • M-12
Front
Axle Maintenance M-3

Front
Axle Shaft Removal M-5

Front
Axle U-Joint B-54, B-55, M-7

Front
Axle Steering Knuckle M-&

Front
Wheel Alignment 0-4

Front
Wheel Bearings B-56, B-57, Q-4
Front
Wheel Toe-in 0-5, 0-6

Front
Wheel Turning Angle 0-9
Fuel
Gauge Float Unit F-76

Fuel
Lines - E-77

Fuel
Pump E-45, E-54, E-60, E-67
Fuel
Pump Check C-23

Fuel
Tank
E-72

G

Gauges, Testing H-l24

General
Specifications A-8
Generator B-16, H-34 thru H-40

Glass
Replacement • T-4
Governor. . .
•.
• U-3
Guides, Valve D"61

H

Hazard
Warning Lights H-139
Head Lamp Aiming H-131, H-132 Head Lamp Replacement H-130
Headlight Dimmer Switch H-l
2
7

Heat Control Valve C-7, F-7 Heated Air System • •
•
F2-2
Heater U-10
Horns.....
....H-137 371