brake fluid JEEP DJ 1953 User Guide

BRAKES

12519

FIG.
P-13—DOUBLE
SAFETY MASTER CYLINDER
1— Boot
2— Snap Ming 3"*—Piston Assembly
4—
Backing
Ring 5—
Master
Cylinder Cup 6—
Master
Cylinder Cup
7— Piston
8—
Master
Cylinder Cup 9—
Cup
Protector
10—Spring 11—
Cylinder
Housing
12—
Cover
Gasket
13—
Cover

14—
Washer
Gasket 15—
Washer
16—
Cover
Bolt
17—
Check
Valve Spring 18—
Check
Valve
19—
Tube
Seat
20— Piston Stop
REASSEMBLY

a.
Prior
to reassembly of the master cylinder, dip

all
components
in clean brake fluid and place on
clean paper or in a clean pan.

b.
Install the primary cup washer, primary cup,
cup protector, and return spring on the secondary piston.
c. Install the piston cups in the double
groove
end
of the secondary piston, so the flat j of the cups face each other (lip of cups away from each other).
Install
the cup expander in the lip
groove
of the
end cup.

cL
Coat the cylinder bore and piston assemblies with clean brake fluid
before
installing any parts

in
the cylinder.
e. Install the secondary piston assembly first and then the primary piston which is supplied in the
repair
kit.

f.
Install the push rod assembly, which includes
the push rod,
boot,
and rod retainer, and secure
with the snap ring. Install the primary piston
stop.

g. Place new rubber check valves over the check valve springs and install in the
outlet
holes, spring
first.

Note:
When replacing a
complete
master cylinder
with a service unit, the original push rod must be used. The push rod retainer and snap ring retainer 12617

FIG.
P-14—REMOVING TUBE SEATS 1
—Screwdriver

2— No. 6-32 Self-Tapping Screw

3—
Tube
Seat must be removed and discarded. As the new unit
has the retainers installed it is only necessary to

install
the push rod until a "snap" is heard and the push rod is retained. 332

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P h.
Install
the tube seats, flat side toward the check

valve,
and press in with tube nuts or the master

cylinder
brake pipe tube nuts.

BLEEDING
a.
Before the master cylinder is installed on the
car,
the unit must be bled.

b.
Support the cylinder assembly in a vise and

fill
both fluid reservoirs with approved brake fluid,

e.
Loosely install a plug in each
outlet
of the

cylinder.
Depress the push rod several times until

air
bubbles cease to appear in the brake fluid.

d.
Tighten the plugs and attempt to depress the piston. The piston travel should be restricted after
all
air is expelled.
e.
Install
the master cylinder on the car and bleed
the hydraulic lines at the wheel cylinder. Refer to
Par.
P-7.

P-21.
Wheel
Cylinder
Reconditioning
•
Refer to Fig. P-15.
Note:
Make sure a replacement brake cylinder
has the same part number as the original cylinder.

FIG.
P-15—WHEEL
BRAKE CYLINDER
1— Boot

2—
Piston

3—
Cylinder
Cup
4—
Cup
Spring
5—
Cylinder

6—
Bleeder
Screw
a.
To remove a wheel cylinder,
jack
up the vehicle

and
remove the wheel, hub, and
drum.
Disconnect
the brake line at the fitting on the brake backing
plate. Remove the brake
shoe
return spring which

will
allow the brake
shoes
at the toe to
fall
clear of the brake cylinder. Remove two screws holding
the wheel cylinder to the backing plate.
b.
Remove the rubber dust covers on ends of

cylinder.
Remove the pistons and piston cups and
the spring.

c.
Wash the parts in clean alcohol.

d.
Examine the cylinder bore for roughness or
scoring.
Check
fit of pistons to cylinder bore.
e. When reassembling the cylinder, dip springs, pistons and piston cups in brake fluid.
Install

spring
in center of the wheel cylinder.
Install

piston cups with the cupped surface towards the

spring
so that the flat surface
will
be against
the piston.
Install
pistons and dust covers.
f.
Install
wheel cylinder to the backing plate and connect brake line and install brake
shoe
return

spring.

g. Replace wheel, hub, and
drum.

h.
Bleed the brake lines (Par. P-7).

P-22. TROUBLE
SHOOTING

P-23.
Squeaky
Brakes

In
most cases, squeaks are entirely eliminated by

correct
adjustment of the brakes. Squeaks may be
caused however, by glazed linings, lining wore thin
to the point of
exposed
rivets or by vibration. A

drum
will
not vibrate when the brake is securing

uniform
contact over the entire lining surface, ex­
cept when due to improper conditions such as the
linings becoming glazed.
Glazed
surface of the

brake
linings may be removed by a stiff
wire
brush.
Occasionally
squeaks are caused by roughened
sur­

face of the
drum,
which can usually be remedied
by rubbing down with emery cloth and by wiping
the brakings surface clean. In extreme cases it may
be necessary to reface the drum in a lathe. Should
this be done, do not remove a metal thickness greater than .030" [0,762 mm.] - .060" [1,52 mm.]

overall
diameter.

P-24. Rattles
in
Brakes

See that the tension of the springs in the brakes

and
attached to the control system are sufficient to

return
brakes and brake mechanism to their normal
position.
Return
springs are so placed that they
keep all slack out of the control system by tension on all joints.

Brakes
will
not rattle inside the
drum
if the springs
holding the
shoes
are kept at the proper tension. 333

p

BRAKES
P-25.
SERVICE

SYMPTOMS
Brakes Drag
Brake
Shoes
Improperly Adjusted
Piston Cups Enlarged . . •.
«•
Mineral
Oil or Improper Brake
Fluid
in System. . .

Improper
Pedal Adjustment
Clogged Master Cylinder By-Pass Port...

One
Brake Drags
Brake
Shoe
Adjustment Incorrect
v Brake
Hose
Clogged.
Return
Spring Broken
Wheel Cylinder Piston
01
Cups
Defective.........
Loose or Damaged Wheel Bearings

Brake Grabs
—
Vehicle Pulls
to One
Side
Grease
or Brake
Fluid
on
Lining................
Dirt
Between
Lining
and Drum

Drum
Scored or Rough
Loose Wheel Bearings. .
Axle Spring Clips Loose
Brake
Backing Plate Loose

Brake
Lining
..

Brake
Shoe
Reversed
Tires
Under-Inflated -
Tires
Worn Unequally
Glazed
or Worn
Lining

Restricted Brake
Line

Excessive Pedal Travel
Normal
Lining
Wear

Lining
Worn Out ... .

Leak
in Brake
Line.

Scored Brake Drums
Incorrect
Brake
Lining.

Air
in Hydraulic System

Spongy Brake Pedal
Air
in
Lines.
Brake
Shoe
Adjustment Incorrect
Insufficient Brake
Fluid

Excessive Pedal Pressure
Grease
or Brake
Fluid
in
Lining

Shoes
Improperly Adjusted

Warped
Brake
Shoes
Distorted Brake Drums
Glazed
or Worn
Lining

Restricted Brake
Line
Faulty
Brake Cylinder Insufficient Brake
Fluid.

Squeaky Brakes
Shoes
Warped or Drums Distorted
Lining
Loose.....
Dirt
Imbedded in
Lining

Improper
Adjustment.

Oil
or Grease on
Lining
Glazed
or Worn
Lining.

Drum
Scored
DIAGNOSIS

PROBABLE
REMEDY

Adjust
Flush
all
lines
with Alcohol. Install new cups in wheel and Master Cylinders

Adjust
Master Cylinder Eye Bolt
Clean
Master Cylinder

Adjust
Replace Replace
Replace
Adjust
or Replace
Replace
Lining

Clean
with Wire Brush

Turn
Drum and Replace
Lining

Adjust
Tighten Tighten
Different Kinds on Opposite Wheels

Forward
and
Rear
Shoes
misinstalled
Inflate
Replace or Rotate Replace Linings

Locate
and Repair

Adjust

Replace
Locate
and Repair Replace or Regrind Replace

Fill
Master
Cylinder
— Bleed Lines
Bleed Lines
Adjust

Fill
Master Cylinder
Replace
Lining
Major
Adjustment
Replace
Replace or Regrind Replace Linings * .

Locate
and Repair
Repair
or Replace
Fill
Master Cylinder Replace
Replace
Wire
Brush or Replace

Adjust
Replace Linings Replace Linings

Turn
Drum and Replace Linings 334