air filter JEEP DJ 1953 Owner's Guide

Fl
EXHAUST EMISSION CONTROL SYSTEMS

12793

FIG.
Fl-1—HURRICANE
F4-134
ENGINE EXHAUST EMISSION CONTROL SYSTEM
1—
Anti-Backfire
Diverter
Valve

2— Air
Pump

3—
Pump
Air
Filter
Injection
Tube(s)
(Inside
Manifold)

5—Air
Delivery
Manifold
6—
Check
Valve
Ignition
timing must be set at 0 or at top dead
center.

Fl-10.
Exhaust Manifold

The
exhaust manifold is provided with a
boss
that is drilled and tapped at each cylinder to accept the

air
delivery manifold and injection tubes.

Fl-11.
MAINTENANCE

Efficient
performance of the exhaust emission con­
trol
system is dependent upon precise maintenance.
In
addition to the air pump and connecting
hoses

and
tubes, this system's efficiency is dependent
upon special carburetor calibration, distributor cen­

trifugal
advance curve and ignition timing setting

which
must be adjusted at 0 or top dead center.

Road
test
is a factory recommended optional serv­ ice every
6,000
miles
[9,600
km.] to evaluate over­

all
performance.

The
following procedure is recommended to assist
in
diagnosing performance and/or emission level
problems that are peculiar to
Exhaust
Emission

Control
System equipped vehicles.

Fl-12.
Carburetor

Check
carburetor number for proper application. (Specifications are listed at the end of this section)

Check
the dash pot and adjust as required.

Proper
carburetor idle mixture adjustment is im­
perative for
best
exhaust emission control.
The
idle adjustment should be made with the en­
gine
at normal operating temperature and air
cleaner
in place. Adjust the throttle
stop
screw to
idle the
engine
at specified RPM. All lights and accessories must be turned off.

Fl-13.
Carburetor
Idle
Setting
NOTE:
The idle mixture adjustment procedure for
the late model
YF-4941S
and
YF-6115S
Carter
Carburetor
equipped with the
External
Idle
Mix­

ture
Limiter
Cap is the same as outlined below
in
Pars.
"A"
through
"D";
however, because of the

Idle
Limiter
Cap,
the idle mixture screw
CANNOT

be adjusted in the counter-clockwise
(rich)
direc­
tion. The adjustment is made from the
rich
stop
position and the mixture screw is turned in (clock­
wise) approximately %
turn
to "Lean Best
Idle."
Refer
to Section E, Fig. E-6.

The
"Lean
Best
Idle"
method of idle setting is as follows:

a.
Any scheduled service of ignition system should
precede this adjustment. 144

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

Fl
b. Connect tachometer to
engine.

c.
Warm
up
engine
and stabilize temperatures.

d.
Adjust
engine
idle to
speed
desired, using throt­
tle idle
speed
adjusting screw.

e.
Carburetors without Idle
Limiter
Cap turn idle mixture screws out (counterclockwise) until a
loss

of
engine
speed
is indicated; then, slowly turn mix­
ture screw in (clockwise-leaner) until maximum

speed
(RPM) is reached. Continue turning in (clockwise) until
speed
begins
to drop; turn mixture
adjustment back out (counterclockwise-richer) un­

til
maximum
speed
is just regained at a "lean as
possible" mixture adjustment.

Fl-14.
Distributor

Check
the distributor number for proper appli­
cation.
Check
the distributor cam dwell angle and
point condition and adjust to specifications or re­ place as required. (Specifications listed at the end
of this section)
Check
ignition timing and set at

0°
or
TDC.

Fl-15.
Anti-iackfire
Diverter Valve

The
anti-backfire valve remains closed
except
when
the throttle is closed rapidly from an
open
position.

To
check the valve for proper operation, accelerate
the
engine
in neutral, allowing the throttle to
close

rapidly.
The valve is operating satisfactorily when
no exhaust system backfire occurs. A further check
to determine whether the valve is functioning can be made by removing from the anti-backfire valve
the large
hose
Which
connects to the check valve.
Accelerate the
engine
to allow the throttle to
close

rapidly.
The valve is operating satisfactorily if a
momentary interruption of rushing air is audible.

Fl-16.
Check Valve

The
check valve prevents the reverse flow of ex­
haust
gases
to the pump in the
event
the pump
should, for any reason,
become
inoperative or should exhaust pressure ever
exceed
pump pressure.

To
check this valve for proper operation, remove the air supply
hose
from the pump at the
distri­

bution manifold.
With
the
engine
running, listen for exhaust leakage at the check valve which is
connected to the distribution manifold.

Fl-17.
Air
Pump

Check
for proper drive belt tension with belt tension
gauge
W-283. The belt strand tension should be

50-60
pounds on a belt with previous service, meas­

ured
on the
longest
accessible span
between
two pulleys. When installing a new belt, adjust the
tension to
60-80
pounds tension. DO NOT PRY
ON
THE DIE
CAST
PUMP
HOUSING.

To
check the pump for proper operation, remove the air
outlet
hose
at the pump.
With
the
engine

running,
air discharge should be
felt
at the pump

outlet
opening. The pump
outlet
air pressure, as determined by the relief valve, is preset and is not
adjustable.

The
air pump
rear
cover assembly, housing the pressed in inlet and discharge tubes, and the pres­
sure relief valve are the only pump
components

recommended for service replacement. These parts
are
to be replaced only when damaged as a result
of handling or in the
event
the relief valve was
tampered with.

Fl-18.
Carburetor
Air
Cleaner

Every
6000
miles
[9,600
km.] clean the inside
sur­

face at the sump and
refill
to indicated oil level with
SAE
40 or 50
engine
oil
above
32 F; SAE 20

below
32 F. Wash filter
element
in kerosene and

drain.
Reassemble the air cleaner.

More
frequent cleaning and replacement is advis­ able when the car is operated in dusty areas or on
unpaved roads. Accumulated dirt restricts air flow,
reducing fuel
economy
and performance.

Fl-19.
REMOVAL
PROCEDURES

The
following paragraphs
give
the procedures for removing the major units of the Exhaust Emission

Control
System and the required equipment
needed.

Fl-20.
Air
Pump

Loosen
the air pump adjusting strap to facilitate

drive
belt removal. Remove the air pump air dis­
charge hose(s) and air filter attachment. Separate
the air pump from its mounting bracket. At time of installation, torque tighten the air pump mount­ing
bolts
to
30-40
lbs-ft. [4,15 a 5,53 kg-m.]. Adjust
the belt strand tension to
50-60
pounds on a belt
with previous service and
60-80
pounds on a new
belt.

Fl-21.
Anti-Backfire
Diverter Valve

The
anti-backfire diverter valve removal requires disconnecting the
hoses
and bracket to
engine
at­
taching screws.

Fl-22.
Air
Distribution
Manifold
and
Injection Tubes

In
order to remove the air distribution manifold
without bending the tubing, which could result in
fractures
or leakage, it is necessary to remove the
exhaust manifold as an assembly from the
engine.

After
the exhaust manifold assembly is removed
from
the
engine,
place the manifold in a vise and

loosen
the air distribution manifold
tube
retaining nuts at each cylinder exhaust port. Tap the injec­
tion
tubes
lightly to allow the air distribution mani­
fold to be pulled away partially from the exhaust manifold. The stainless steel injection
tubes
in the
exhaust manifold may have
become
partially fused
to the air distribution manifold and, therefore, may
require
application of heat to the joint in order to
separate. While applying heat to the joint, rotate
the injection
tubes
with pliers being careful not to
damage the
tubes
by applying excessive force.

At
time of installation, the air injection
tubes
must
be positioned into the exhaust manifold prior to
placing the exhaust manifold assembly on the en­ gine.

Note:
Two different length injection
tubes
are used.

The
shorter length injection
tubes
must be inserted into cylinders 1 and 4. 145

Fl

EXHAUST
EMISSION CONTROL SYSTEMS The
air distribution manifold should be installed
after the exhaust manifold assembly is torqued
to the cylinder head. The recommended procedure
for exhaust manifold assembly installation is as follows:
Clean
the mating surface of both the
manifold and cylinder head.
Install
the exhaust manifold to the cylinder head using a new gasket.

Tighten
the manifold to cylinder head, attaching
bolts
down evenly.
Finish
torque tightening to 29
to 35 ft. lbs. [3,4 a 4,8 kg-m.].

Fl-23.
REQUIRED
EQUIPMENT

Each
station licensed to perform repair and main­
tenance on the Exhaust Emission Control System
must be equipped with that equipment necessary
for major
engine
tune-up analysis which shall in­ clude at least the following or equivalent.
Ignition Analyzer Oscilloscope
Ammeter
Ohmmeter
Voltmeter Tachometer
2 Vacuum Gages

Pressure
Gage (0-10 psi.)

Cam
Angle Dwell Meter Ignition Timing
Light

Engine
Exhaust Combustion Analyzer Compression Tester

Fl-24.
REPLACEMENT
PARTS

Parts
necessary to repair and/or maintain the

Exhaust
Emission Control System are available through any Jeep
SALES CORPORATION
ware­
house.

Fl-25.
WARRANTY

All
parts of the Exhaust Emission Control System

are
covered by the Manufacturer's Warranty as stated in the Warranty Service and 'Jeep' Quality
Maintenance Plan booklet.

Fl-26.
EXHAUST EMISSION CONTROL
SYSTEM
DIAGNOSIS GUIDE
Pump Noisy

Hoses Touching Other Parts of Engine or Body (Hood).

Note:
The air pump is not completely noiseless.

Under
normal conditions, pump
noise
rises in pitch as
engine
speed
increases. It is also desirable to
allow for normal break-in wear of the pump prior
to replacement for excessive noise.

Pump Seized

Replace
pump.

Leak
In
Hose

Check
for leaks; using
soap
and water — tighten
clamps or replace
hoses.
Pump
Inoperative

Loose Belt — tighten belt — do not pry on housing.

Filter
Plugged — replace.

Exhaust Backfire

Check
for vacuum leaks — correct as necessary.
Check
air filter for excessive
restriction
— replace as necessary.

Check
anti-backfire valve — replace as necessary.

Induction System Backfire

Verify
engine
timing and distributor dwell.

Verify
accelerator pump charge. 146

'Jeep'
UNIVERSAL SERIES
SERVICE
MANUAL

Fl
Fl-27.
EXHAUST EMISSION CONTROL SYSTEM MAINTENANCE CHART

Efficient
performance of the Exhaust Emission
Control
System is
dependent
upon precise main­tenance. As indicated in the following chart, it is very important that all of the maintenance require­

ments
listed are performed with extreme care at
the specific intervals indicated.

OPERATION
Thousands of miles* or
number of months whichever
occurs first 2
6
12 18
24 30

R R
R R
R R

O O o O
O
o O

R
O
o
o

R
o

o o

o
o

o
O
o
Inspect engine-driven
belts
for condition and tension...
Replace positive crankcase ventilation valve (PCV) Replace filter on exhaust emission control system

Clean
carburetor air cleaner

Engine
tune-up
Check
engine
timing

Adjust
carburetor idle
speed
and mixture

Perform
factory-recommended road
test
for evaluation of overall performance and handling

R
— Required Services
O
— Optional Services
Miles
2,000

6,000

12,000
18,000
24,000
30,000
Kilometers

3,200

9,600

19,200
28,800
38,400 48,000

Fl-28.
EXHAUST EMISSION CONTROL SYSTEM CARBURETOR SPECIFICATIONS

Make
Models

Part
Number
Throttle
Bore
Main
Venturi

Low
Speed Jet

Main
Metering Jet

Idle
Port
Nozzle Bleed in Body
Pump Jet

Float
Level
Dash
Pot Setting

Engine
Idle
RPM:
with Distributor Model
IAY-4401A.
with Distributor Model
IAY-4401B.
Carter
— Single Bore

^ an H
YF
4366S ana 4941S, 6115S

1M"
[3,81 cm.]

IX"
[3,18 cm.]
.035"
[0,889
mm.] .089" [2,26 mm.]
.184" x .030" [4,70 a
0,765]
.028"
[0,713
mm.]
.024"
[0,610
mm.] lW [6,74 mm.]
%"
[3,75 mm.] 650 — 700 700 — 750

Fl-29.
EXHAUST EMISSION CONTROL SYSTEM DISTRIBUTOR SPECIFICATIONS

Engine

Make
Models
Rotation
Point Opening

Breaker
Lever
Tension..
Cam
Angle (Dwell)
Condenser Capacity
Dist.
Degrees and RPM:
Start..

Intermediate

Maximum

TIMING:
Crankshaft

Mark
Location

Firing
Order
F4-134
Prestolite

IAY-4401A

CCW
Rotor End
.020"
[0,508
mm.|
17 — 20 ozs. [482 a 567 gr.l
42°

.25 — .28 mfd.

0°
— 300
3°
— 375

13.5°
— 1700

0°
TDC @ Idle

Crankshaft
Pulley
1-3-4-2
Prestolite

IAY-4401B

CCW
Rotor End
.020"
[0,508
mm.]
17 — 20 ozs. [482 a 567 gr.
42°

.25 — .28 mfd.

0°
— 450

4.5°
— 550

13.5°
— 1700

0°
TDC @ Idle

Crankshaft
Pulley
1-3-4-2

Fl-30.
SPARK PLUG
GAP

Spark
Plug Gap. .030"
[0,765
mm.] 147

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

Fl
EXHAUST
EMISSION
CONTROL
SYSTEM

Contents

DAUNTLESS
V-6
ENGINE
SUBJECT
PAR.

GENERAL
.F2-1
HEATED
AIR
SYSTEM.
. F2-2
Testing
Thermo
Air
Cleaner
F2-4
Positive
Crankcase
Ventilation
Valve.
. . .F2-6

Vacuum
Motor Replacement . .F2-8
Air
Cleaner Sensor Replacement F2-9
Replacement Procedures F2-7

AIR
PUMP
.F2-10

AIR
FILTER.
F2-11

AIR
DELIVERY
MANIFOLD.
F2-12

AIR INJECTION TUBES.
F2-13

ANTI-BACKFIRE
VALVE..
.F2-14
ENGINE COMPONENTS
.F2-15
MAINTENANCE
.F2-3
Carburetor
F2-16, F2-17

Distributor
F2-18

Anti-Backfire
Valve . . F2-19
Check
Valve..
F2-20

F2-1.
GENERAL
—V-6
Engine

The
Dauntless V-6
engine
Exhaust
Emission
Con­

trol
System consists of a belt-driven air pump

which
directs compressed air through connecting
hoses
to a steel distribution manifold into stainless steel injection
tubes
in the exhaust port adjacent
to each exhaust valve.
This
air, with its normal
oxygen
content, reacts with the hot but incom­
pletely burned exhaust
gases
and permits further combustion in the exhaust port or manifold.

The
Exhaust
Emission System on V6-225
engines

limits
the hydrocarbon and carbonmonoxide emis­sions from the exhaust system. The system includes

an
engine
designed for low emissions and lean
carburetor
calibration at idle and part throttle.

The
lean carburetion is possible because of the
heated air system that is part of the Emission
System.
See Fig. F2-2.
With
the heated air system
operating, inlet air temperature is around
115°F.
[46°C],
after the first few minutes of operation.

This
makes the use of lean (hot weather)
cali­
bration
possible, and the vehicle
still
responds and

drives
well in cold weather.

The
engine
has a "ported"
spark
advance, with the

vacuum
take-off just above the throttle valve, so that there is no vacuum advance at closed throttle,
but there is vacuum advance as
soon
as the throttle is opened slightly. To reduce emissions at idle and
at lower
engine
speeds, the
engine
timing is such
that the distributor
will
not have centrifugal ad­
vance until about 900 RPM.
F2-2.
HEATED
AIR
SYSTEM

The
heated air system on late model V6 engines,
consists of a manifold heat collector, a heated-air
SUBJECT
PAR.

Air
Pump F2-21
Intake
Manifold F2-22
Carburetor
Air Cleaner F2-5, F2-23

REMOVAL PROCEDURES
F2-24
Air
Pump. F2-25
Anti-Backfire
Valve..
. . .F2-26
Air
Distribution Manifold,

And
Air Injection Tubes F2-27

REQUIRED
EQUIPMENT..
. F2-28
REPLACEMENT
PARTS..
.F2-29

WARRANTY
F2-30
DIAGNOSIS GUIDE
F2-31
MAINTENANCE CHART.
F2-32
GENERAL
SPECIFICATIONS
F2-33

CARBURETOR SPECIFICATIONS.
.... .F2-34

DISTRIBUTOR SPECIFICATIONS
. .F2-35
SPARK PLUG GAP
F2-36
pipe, a adapter elbow and an air cleaner contain­ing temperature control doors operated by vacuum
through a temperature sensor. The heat
stove
is a
sheet
metal cover, shaped to and bolted on with
the right exhaust manifold. Air drawn in along the lower
edge
of the
stove
passes across the mani­
fold surface, picking-up heat. The heated air is
drawn
out from the front of the manifold, through
the heated air pipe and adapter elbow into the
snorkel
of the air cleaner.

The
temperature control air cleaner is designed to mix this heated air with cold air from under the
hood so that carburetor inlet air temperature aver­
ages
about
115°F.
[46°C.].
This
mixing is
done
by two air doors, a cold air door and a hot air door,

which
move
together
so that when the cold air door is closed, the hot air door is open and vice
versa.
Most of the time, both doors
will
be partially
open as required to control the temperature. When
the underhood temperature reaches about 135
°F
[57°C]
the cold air door
will
open wide and the
hot air door
will
close
tight See Fig. F2-3. Ob­ viously, if underhood temperatures rise above
135°F.
[57°C]
the air cleaner
will
no longer be
able to control temperatures and the inlet air tem­

perature
will
rise with underhood temperature.
The
temperature doors are moved by a diaphragm
type vacuum door. When there is no vacuum pres­ ent in the motor, the diaphragm spring forces the
cold air door open and the hot air door closed.

Whenever
the
engine
is running, the amount of
vacuum
present in the vacuum motor depends on
the temperature sensor in the air cleaner which is located in the vacuum line
between
the intake
manifold and the vacuum motor. In the sensor, a 149

F2

EXHAUST
EMISSION
CONTROL
SYSTEMS

FIG.
F2-5—COLD
AND
HOT AIR
DOORS
PARTIALLY
OPEN
1— Motor
2—
Air
Cleaner

3—
Sensor
4—
Temp
Sensing Spring 5—
Air
Bleed Valve
6— Hot
Air
Pipe
7—
Diaphragm
Spring 8—
Diaphragm

9—
Control
Damper
10—
Linkage

11—
Air
Inlet 12—
Vacuum
Chamber
13—
Snorkel
Tube stationary
and to
make sure
the
gasket seals
properly. system vacuum motor
or
sensor,
use the
procedure
outlined
in the
following paragraphs.

F2-6.
Positive Crankcase Ventilator Valve
Every
12,000
miles
[19,200
km.] replace
the
posi­
tive crankcase ventilator valve. Also, remove
the
PCV
filter from inside
the air
cleaner. Wash filter

in
suitable solvent
and dry by
blowing lightly
with
an air
hose.
Oil
with
engine
oil;
shake
out
excess
oil.
Reinstall
the
filter. After installing
new

valve, always readjust
engine
idle.
F2-7.
Replacement Procedures

Should
the
test
performed
in
paragraph
F2-4
indicate necessary replacement
of the
heated
air
F2-8.
Replacement of
Vacuum Motor

a.
Drill
center
of two
spot
welds using
a ]f6
inch [1,59
mm.]
drill.
Do not
center punch.
b. Enlarge
two
holes
using
a
j& inch
[3,96 mm.]

drill.

Caution:
Use
extreme care
not to
damage
the ail

cleaner snorkel.
c. Remove vacuum motor retainer strap.
See
Fig.

F2-6.

d.
Lift
vacuum motor, cocking
it to one
side
to

unhook motor linkage
at the
control door. 154

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

F2

14043

FIG.
F2-6—REPLACING VACUUM MOTOR ASSEMBLY

A—Drill
VW
Hole
B—Sensor
Unit
Replacement Position
1—
Motor
3—Sensor
Unit

2—
Spot
Welds
4—Retaining
Strap
•e.
Drill
a
%j
inch [2,78 mm.] hole in snorkel tube

at
point
"A"
as shown in Fig.
F2-6.
f.
Use the motor strap retainer and the
sheet
metal

screw
provided in the motor replacement kit to secure the retainer and motor to the snorkel tube.
g. Make sure the screw
does
not interfere with the
operation of the damper assembly. Shorten screw
if
required.

F2-9.
Replacement
of Air
Cleaner Sensor

a.
Remove two sensor retaining clips by
prying.
See

Fig.
F2-7.

b.
Pull
vacuum
hoses
from sensor.

c.
Note
carefully the installed position of the sensor so that you can install new sensor in same position.

Then
remove sensor.

d.
Install
sensor and gasket assembly in air cleaner

m
same position as noted in
step
c.
This
is to eliminate the possibility of interference with the air

filter
element.
e.
Install
sensor retaining
clip,
meanwhile support­
ing
sensor at B around the outside rim to prevent 14042

FIG.
F2-7—REPLACING SENSOR ASSEMBLY

1—Sensor
Retaining
Clip
damage to the temperature sensing spring. See

Fig.
F2-7.

f.
Reinstall
vacuum hoses.

F2-10.
AIR
PUMP
The
air injection pump is a positive displacement
vane type which is permanently lubricated and
requires
no periodic maintenance.

The
pump contains an integral relief valve which
controls the
air
supplied to the
engine
exhaust ports

during
high speed operation to limit maximum exhaust system temperatures.

F2-11.
AIR
FILTER
The
air injection system draws clean air from the
carburetor
air filter through an inlet hose, into the

air
pump and from the pump through two
outlets
(one for each cylinder head).

F2-12.
AIR
DELIVERY MANIFOLD

The
air delivery manifolds constructed of cold
rolled
steel with a zinc plating, distribute the air

from
the pump to each of the air delivery tubes in

a
uniform manner.

Two
check valves are included to prevent the
reverse
flow of exhaust
gases
to the pump should
the pump drive
fail.
This
reverse flow would dam­
age the air pump and connecting hose.

F2-13.
AIR
INJECTION TUBES
The
air injection tubes of stainless steel are in­ serted into machined
bosses
of the cylinder head.

The
tubes project into the exhaust ports directing
air
into the vicinity of the exhaust valve stem.

F2-14.
ANTI-BACKFIRE VALVE
The
anti-backfire valve is used to provide a "gulp" of air into the
engine
induction system during
rapid

throttle opening and subsequent closure.
During
rapid
throttle closure, the valve
opens
for approxi­
mately one (1) second and bleeds air into the
intake
manifold through a fitting in the carburetor.

Its
function is to bleed an adequate amount of

air
below the carburetor throttle plate to compen­ sate for the
overrich
fuel mixture normally inducted
into the combustion chamber during
rapid
throttle

closure.

Filtered
air from the pump is provided to the
anti-backfire
valve by means of a connecting hose.

An
exhaust system backfire
will
result if the valve

fails
to function properly.

F2-15.
ENGINE COMPONENTS
The
following item varies in design or specifications

from
those
on vehicles not equipped with the Ex­

haust
Emission
Control
System.

F2-16.
Carburetor

Check
carburetor number for proper application. Specifications are listed in this section.

Proper
carburetor idle mixture adjustment is im­ perative for
best
exhaust emission control.

The
idle adjustment should be made with the en­
gine
at normal operating temperature, lights and accessories off and the air cleaner in place.
Adjust
155

F2
EXHAUST EMISSION CONTROL SYSTEMS
the throttle
stop
screw to idle the
engine
at 650
to 700 rpm.

F2-17. Carburetor Idle Setting
The
"Lean
Best
Idle"
Method of Idle Setting is as
follows:

a.
Any scheduled service of ignition system should
precede this adjustment

b.
Connect tachometer to engine.

c.
Warm
up
engine
and stabilize temperatures.

d.
Adjust
engine
idle to speed desired, using throt­
tle idle speed adjusting screw.
e.
Turn
idle mixture screws out (counterclockwise)

until
a
loss
of
engine
speed is indicated; then slowly
turn
mixture screws in (clockwise-leaner)
until
maximum speed (rpm) is reached. Continue

turning
in (clockwise) until speed begins to drop;

turn
mixture adjustment back out (counterclock­
wise-richer)
until maximum speed is just regained

at
a "lean as possible" mixture adjustment.

F2-18. Distributor
The
ignition distributor used with the
Exhaust
Emission
Control
System is the same as that used
on
engines
without
Exhaust
Emission
Control.
Check
the distributor cam dwell angle and point
condition.
Check
ignition timing and adjust to specifications shown on the last
page
of this section.

F2-19.
Anti-Backfire
Valve

The
anti-backfire valve remains closed except when
the throttle is closed rapidly from an open position.
To
check the valve for proper operation, accelerate
the
engine
in neutral, allowing the throttle to close

rapidly.
The valve is operating satisfactorily when
no exhaust system backfire occurs. A further check
to determine whether the valve is functioning can
be made by removing from the anti-backfire valve
the large
hose
which connects the valve to the

pump.
With
a finger placed over the open end of
the
hose
(not the valve), accelerate the
engine
and allow the throttle to close rapidly. The valve is
operating satisfactorily if a momentary air rushing
noise is audible.

F2-20.
Check
Valve

The
check valves in the lines to the air distribution manifolds prevent the reverse flow of exhaust
gases

to the pump in the event the pump should, for

any
reason,
become
inoperative or should exhaust

pressure
ever exceed pump pressure.

To
check this valve for proper operation, remove the air supply
hose
from the pump at the check

valve.
With
the
engine
running, listen for exhaust
leakage at the check valve which is connected to
the distribution manifold.

F2-21.
Air
Pump

Check
for proper drive belt tension with belt tension
gauge
W-283. The belt strand tension should be 60 pounds measured on the
longest
accessible span
between two pulleys. DO NOT PRY ON THE

DIE
CAST
PUMP
HOUSING. To
check the pump for proper operation, remove
the air
outlet
hose
at the pump.
With
the
engine

running,
air discharge should be felt at one of
the pump
outlet
openings. The pump
outlet
air
pressure,
as determined by the relief valve, is preset
and
is not adjustable.

The
air pump
rear
cover assembly, housing the pressed in inlet and discharge tubes, and the pres­
sure
relief valve are the only pump components
recommended for service replacement. These parts
are
to be replaced only when damaged as a result
of handling or in the event the relief valve was
tampered with.

F2-22.
Intake Manifold

Intake
manifold leaks must not be overlooked. Air
leakage at the intake manifold may be compen­
sated for by
richer
idle mixture setting, however, this
will
usually cause uneven fuel-air distribution
and
will
always result in
loss
of performance and
exhaust emission control. To check for air leakage
into the intake manifold, apply kerosene or naph­
tha,
on the intake manifold to cylinder head joints

and
observe whether any changes in
engine
rpm

occur.
If an air leak is indicated, check the mani­
fold to cylinder head bolt torque. The correct torque is 25-35 lbs. ft. [3,46 a 4,84 kg-m.]. If the

leak
is
still
evident,
loosen
the manifold assembly

and
torque-tighten the bolts evenly.
Start
from the center and use proper torque values. Replace the
manifold
gasket if the leak
still
exists.
Clean
both
mating surfaces and check for
burrs
or other ir­

regularities.

Always
torque the bolts evenly to the specified
torque value to prevent warpage.

F2-23.
Carburetor
Air
Cleaner
—Oil
Bath

Every
6,000
miles [9,600 km.] disconnect attach­

ing
hoses
and unscrew the wing nut from the top
of the air cleaner and lift it off the carburetor.

Lift
the cover and filter element off the oil sump.

Clean
the inside surface of the sump and
refill
to

indicated
oil level with SAE 40 or 50
engine
oil
above 32 F; SAE 20 below 32 F.
Wash
filter element in kerosene and
drain.
Reassemble the air

cleaner
and install on carburetor.

More
frequent cleaning and replacement are advis­ able when the car is operated in dusty areas or on

unpaved
roads. Accumulated
dirt
restricts air flow,
reducing
fuel economy and performance.

F2-24.
REMOVAL PROCEDURES
The
following paragraphs
give
the procedures for removing the major units of the exhaust emission
control
system and the required equipment needed.

F2-2S.
Air
Pump

Loosen
the air pump mounting bracket bolts. Re­ move the air pump air hose(s). Separate the air pump from its mounting bracket. At time of install­
ation,
torque tighten the air pump mounting bolts
to
30-40
lbs.-ft [4,15 a 5,53 kg-m.].
Adjust
the
belt strand tension to 60 pounds. 156

F2
EXHAUST EMISSION CONTROL SYSTEMS
F2-3L
EXHAUST EMISSION CONTROL SYSTEM
DIAGNOSIS
GUIDE

Pump Noisy
Hoses Touching Other Parts of Engine or Body (Hood).

Note:
The Air Pump is not completely noiseless.

Under
normal conditions, pump
noise
rises in pitch as
engine
speed
increases. It is desirable to allow
for normal break-in wear of the pump prior to re­
placement for
excessive
noise.
Pump Seized
Replace pump.
-
do not pry on housing.
Leak
In Hose

Check
for leaks; using
soap
and water, tighten clamps or replace
hoses.

Pump Inoperative
Loose Belt — tighten belt
-

Filter
Plugged — replace.

Exhaust
Backfire

Check
for vacuum leaks — correct as necessary.
Check
anti-backfire valve — replace as necessary
Induction System Backfire

Verify
engine
timing and distributor dwell.
Verify
accelerator pump charge.

F2-32.
EXHAUST EMISSION CONTROL SYSTEM MAINTENANCE CHART

Efficient
performance of the Exhaust Emission very important that all of the maintenance require-

Control
System is
dependent
upon precise main-
ments
are performed with extreme care at the
tenance. As indicated in the following chart, it is specific interval indicated.
Thousands of miles* or

OPERATION
number of months whichever occurs first 2 6 12 18 24 30
Inspect engine-driven
belts
for condition and tension R R
Replace positive crankcase ventilation valve
(PCV)
R R

Check
for free operation of exhaust manifold heat control valve O O O O O

Clean
carburetor air cleaner — Oil Bath O O O O O
Replace carburetor air cleaner
element
— Dry Type O
Check
heated air system O O

Engine
tune-up O O

Check
engine
timing R O O O
Adjust
carburetor idle
speed
and mixture R O O O

Perform
factory-recommended road
test
for evaluation of overall performance and handling O O O O O

R
— Required Services O — Recommended Services

*
Miles Kilometers
2,000
—
3,200

6,000
—
9,600

12,000
—
19,200 18,000
—
28,800
24,000
—
38,400
30,000
—
48,000

F2-33.
GENERAL SPECIFICATIONS
Air
Pump Belt Tension 60 lb.

Rotor
Ring Screw Torque . 37 lb-in.
Housing Cover Bolt Torque 10 lb-ft. Speed Ratio, Air Pump to Engine
1
\i to 1

F2-34.
EXHAUST EMISSION CONTROL SYSTEM CARBURETOR SPECIFICATIONS

Make
Rochester Model Designation 2G Code Number
7027082
—
7041185

Choke
Manual
Number of Barrels 2

Throttle
Bore... \W [3,65 cm.]
Main
Metering Jet Production .051" - 60° [1,29 mm.]
High
Altitude — over
5000
ft .049" - 60° [1,24 mm.]
—
over
10,000
ft .047" - 60° [1,19 mm.]

Float
Level
Adjustment* 1%," [2,94 cm.]
Float
Drop Adjustment l%" [4,76 cm.]
Pump Rod Adjustment** 1%" [2,94 cm.]
Engine
Idle
R.P.M.
(In Neutral) 650 to 700

Initial
Idle Speed-screw
setting
3 turns in

Initial
Idle Mixture-screw
setting
2 turns out
Dash
Pot Setting. Y%w [3,75 mm.]
*From
air horn gasket to top of float at toe.

**From
air cleaner ring to top of pump rod.
158

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

U
DESCRIPTION
—
Continued

AXLES

W-99* Gauge — Pinion & Ring
Gear
Setting
W-104-B* Puller — Tapered Roller Bearing Removing
W-126* Driver — Pinion Bearing Cup
W-128* Installer — Differential Inner Oil Seal W-129 Spreader — Differential
Carrier
Housing
W-138* Driver & Adapter —
King
Pin Bearing
W-144* Wrench — Wheel Bearing Adjusting Nut W-147* Driver — Pinion Oil Seal W-163* Puller
—-
Axle Shaft Drive Flange
W-186* Driver — Axle Shaft Oil Seal
W-188* Driver — Differential Case Bearing W-251* Puller — Pinion Oil Seal
W-262*
Sleeve
— Pinion Bearing Installing

W-263
Semi-Floating
Rear
Axle Shaft Oil Seal W-264* Driver — Pinion Outer Bearing Cup
W-297* Torque Wrench — Pinion Bearing Adjusting W-343* Remover
85
Installer —
Rear
Axle Bearing (Flanged Axle)
W-344* Installer — Pinion Inner Bearing Cups

C-319-A
Puller —
Rear
Wheel Hub (Tapered Axle Shaft)
C-690 Checking Scale —
King
Pin Bearing Preload DD-914-P Press — Tapered Roller Bearing Removing
DD-914-9 Reducer Ring — Differential & Pinion Bearings (Use with DD-914-P)

C-3
716 Driver — Differential
Carrier
Bearing C-4142
Gear
Rotating Tool —
Trac-Lok
Differential
**Jeep*
exclusive
tool

Steering
Group

C-3646 Puller, Steering Shaft Arm

Brake
Group

W-172 Puller, Parking Brake Drum
U-12.
STflNDfiRD
AND
RECOMMENDED
TOOLS

Tool
Description
ENGINE

W-292
Tester — Cooling
System
Thermostat
C-119 Indicator — Cylinder Bore C-385 Compressor — Piston Ring
C-647 Fixture — Spring Testing
C-823
Hone
— Cylinder Bore Refinishing
C-3012 Reamer — Cylinder Ridge
C-3250 Pliers — Radiator fis Heater
Hose
Wire Clamp
C-3411
Gauge — Pressure & Vacuum
C-3422-A Compressor — E-type Valve Spring
C-3501
Hone
— Cylinder
Deglazing
C-3514
Flusher — Cooling
System

C-3886 Fixture — Carburetor Holding C-3896-A Tachometer — Portable
C-3943 Gauge — Compression Checking
C-3952 Torque Wrench, 150
lb-ft.
Swivel Head C-3953 Stand, Engine Repair
C-3959 Light — Ignition Timing
C-4065 Wrench — Oil Filter Removing
C-4080 Tester — Cooling
System
fig
Pressure Cap

ELECTRICAL

40B Hydrometer — Battery Service
W-291 Tester — Instrument
C-3674
Aimers —
Headlight
(Pair)
C-3829 Tester —
Diode
Polarity
C-3888 Tester — Volt-Ampere C-3950 Tester — 12V 60 Amp. Carbon Pile Resistor 361