radio JEEP GRAND CHEROKEE 2004 WK / 3.G Owners Manual

REMOTE KEYLESS ENTRY
This system allows you to lock or unlock the doors and
liftgate or activate the panic alarm from distances up to
about 23 feet (7 meters) using a hand held radio trans-
mitter. The transmitter need not be pointed at the vehicle
to activate the system.
To Unlock the Doors and Liftgate
Press and release the ªUnlockº button on the key fob
once to unlock the driver's door, or twice (within 5
seconds) to unlock all doors and liftgate. The illuminated
entry system will also come on.
NOTE:The system can be programmed to do the
following:
²unlock all the doors on the first button press
²flash the turn signals with unlock
²On vehicles equipped with an overhead console these
functions can be selected at the overhead console
using the ªCustomer Programmable Features.º Refer
to ªOverhead Console Ð Customer Programmable
Featuresº in this section, otherwise see your autho-
rized dealer.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To Lock the Doors and Liftgate
Press and release the ªLockº button on the key fob to lock
all doors and liftgate. If you wish, the horn can be
programmed to chirp once and/or the turn signals can be
programmed to flash once to show the system is acti-
vated. For customer programmable features, refer to
ªOverhead Consoleº in this section for programming
details, otherwise see your authorized dealer.
Using the Panic Alarm
To turn on the panic alarm feature, press and release the
PANIC button with the ignition off. When the panic
alarm is on the headlights and marker lights will flash,
the horn will pulse on and off and the interior lights will
turn on.
The panic alarm will stay on for 3 minutes unless you
turn it off by pressing the PANIC button a second time or
by starting the vehicle and accelerating to 15 mph (24
km/h).
General Information
This device complies with FCC rules part 15 and with
RSS-210 of Industry Canada. Operation is subject to the
following two conditions: (1) This device may not cause
harmful interference and (2) This device must accept any
interference that may be received, including interference
that may cause undesired operation.
If your transmitter fails to operate from a normal dis-
tance, check for these two conditions.
1. Weak batteries in transmitter. The expected life of
batteries is from one to two years.
2. Closeness to a radio transmitter such as a radio station
tower, airport transmitter, military base, and some mobile
or CB radios.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21
2

Power Reclining Seat
The recliner control is on the outboard side of the seat.
Use this switch to recline the seatback and to return the
seatback to the upright position.
WARNING!
Do not ride with the seatback reclined so that the
seat belt is no longer resting against your chest. In a
collision you could slide under the seat belt and be
seriously or even fatally injured. Use the recliner
only when the vehicle is parked.
Memory System Ð If Equipped
If your vehicle is equipped with this system, your Re-
mote Keyless Entry Transmitter or Memory System But-
tons on the driver's door panel can be used to recall the
driver's seat, driver's outside rear view mirror, and radio
station presets to saved positions.
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Press the memory button ª1º if you are setting the
memory for driver one or number ª2º if you are setting
the memory for driver two.
3. Adjust the seat, recliner, and driver's outside rear view
mirrors to the desired position.
4. Set the radio station presets as you desire (up to 10 AM
and 10 FM station settings).
5. Press and release the SET button. An indicator light on
the set switch will flash, telling you that you are in the set
memory mode.6. Press and release button number ª1º or number ª2º on
the driver's door, depending on which transmitter you're
using. The flashing indicator light on the set switch will
go out telling you that the driver memory has been set.
If your remote keyless entry transmitter is lost, you may
order a new transmitter from your local authorized
dealer. You must designate transmitter #1 or #2. Your
authorized dealer will have to program your vehicle to
match the new transmitter.
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

to turn this feature on or off. Also, refer to ªWindshield
Wipers and Washersº in this section for more information
NOTE:When your headlights come on during the
daytime, the instrument panel lights will automatically
dim to the lower nighttime intensity. Refer to ªInstru-
ment Panel and Interior Lightsº below for setting the
instrument panel lights to full daytime intensity.
Instrument Panel and Interior Lights
When the multi-function control lever is in the parklight,
headlights, or AUTO position (if equipped), rotating the
center portion of the lever up and down will increase and
decrease the brightness (dimmer control) of the instru-
ment panel lights. Full daytime brightness on all elec-
tronic displays (odometer, overhead console, radio, and
Automatic Climate Control (if equipped) is obtained by
rotating the center portion of the control to the first
detent above the dimmer range. Rotating the control to
the second detent above the dimmer range turns theinterior lights on. Rotating the control to the ªOffº
(extreme bottom) position disables all the interior lights,
even when the doors and liftgate are open. While in the
ªOffº position the instrument panel lighting is at the
lowest light level and may not be suitable for night
driving.
Daytime Running Lights Ð Canada Only
The headlights come on at a low intensity level whenever
the engine is running. The lights remain on until the
ignition switch is turned OFF or the parking brake is
engaged. The headlight switch must be used for normal
night time driving.
Lights-On Reminder
If the headlights or parking lights are on after the ignition
is turned OFF, a chime will sound when the driver's door
is opened.
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

when valid tire pressure sensor messages have been
received from all 4 road tires. TPM system function is
temporarily unavailable due to external electromagnetic
interference, such as electronic devices or nearby radio or
TV towers.
4. In addition to monitoring the vehicle tires, the TPM
system monitors faults within the system. When any
fault has been set, the TPM system will display TIRE
SENSOR BAD/MISSING. Be sure to inspect your tires for
proper inflation pressure. After you determine that your
tires are properly inflated, see your authorized dealer for
service to diagnose the problem with the TPM system.5. With the 5 Tire TPM System, if a road tire is replaced
by the spare, the TPM system will automatically detect
that the tires have been switched (after the ignition has
been cycled) and display SPARE SWAP DETECTED
along with a chime. This could take up to 10 minutes
with vehicle speed above 25 mph (40 km/h).
6. With the 4 Tire TPM System, if a road tire is replaced
by the spare, the TPM system will display TIRE SENSOR
BAD/MISSING. This is due to the spare tire not being
equipped with a tire pressure sensor. Once the road tire is
repaired and/or installed back on the vehicle with the
proper tire pressure the message will be removed. This
could take up to 10 minutes with vehicle speed above 25
mph (40 km/h).
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

the liftgate will unlock at the first press of the remote
keyless entry unlock button. Pressing the STEP button
when in this display will select DRIVER'S DOOR 1ST or
ALL DOORS.
Remote Linked To Memory? (Available with
Memory Seat Only)
When this feature is selected the memory seat, mirror,
and radio settings will return to the memory set position
when the remote keyless entry ªUnlockº button is
pressed. If this feature is not selected then the memory
seat, mirror, and radio settings can only return to the
memory set position using the door mounted switch.
Pressing the STEP button when in this display will select
ªYesº or ªNo.º
Sound Horn On Lock?
When this feature is selected a short horn sound will
occur when the remote keyless entry ªLockº button is
pressed. This feature may be selected with or without theflash lights on lock/unlock feature. Pressing the STEP
button when in this display will select ªYesº or ªNo.º
Flash Lights On Lock/Unlock?
When this feature is selected, the front and rear turn
signals will flash when the doors are locked or unlocked
using the remote keyless entry transmitter. This feature
may be selected with or without the sound horn on lock
feature selected. Pressing the STEP button when in this
display will select ªYesº or ªNo.º
Headlamp Delay
When this feature is selected the driver can choose, when
exiting the vehicle, to have the headlamps remain on for
30, 60, or 90 seconds, or not remain on. Pressing the STEP
button when in this display will select 30, 60, 90, or OFF.
Headlamp On With Wipers? (Available with Auto
Headlights Only)
When this feature is selected and the headlight switch
has at least once been moved to the AUTO position, the
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97
3

To set the variance: Turn the ignition ON and set the
display to ªCompass/Temperature.º Press the RESET
button approximately five seconds. The last variance
zone number will be displayed. Press the STEP button to
select the new variance zone and press the RESET button
to resume normal operation.
GARAGE DOOR OPENER Ð IF EQUIPPED
The HomeLinktWireless Control System provides a
convenient way to replace up to three hand-held radio-
frequency (RF) transmitters used to activate devices such
as gate operators, garage door openers, entry door locks,
security systems, even home lighting. Additional
HomeLink information can be found at:
www.homelink.comor by calling1-800-355-3515.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Programming HomeLink
NOTE:It is recommended that a new battery be placed
in the hand-held transmitter of the device being pro-
grammed to HomeLink for quicker training and accurate
transmission of the radio frequency signal.
WARNING!
Vehicle exhaust contains carbon monoxide, a danger-
ous gas. Do not run the vehicle's engine while
programming HomeLink. Exhaust gas can cause se-
rious injury or death.
WARNING!
Your motorized door or gate will open and close
while you are programming HomeLink. Do not
program HomeLink if people or pets are in the path
of the door or gate. A moving door or gate can cause
serious injury or death to people and pets or damage
to objects.
1. Position the end of your hand-held transmitter 1-3
inches (5-14 cm) away from the lower left corner of the
EVIC display while keeping the display in view.
NOTE:Some gate operators and garage door openers
may require you to replace the next step with procedures
noted in the9Gate Operator/Canadian Programming9
section.
2. Simultaneously press and hold both the desired
HomeLink button and the hand-held transmitter button.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Gate Operator/Canadian Programming
Canadian radio-frequency laws require transmitter sig-
nals to9time-out9(or quit) after several seconds of
transmission - which may not be long enough for
HomeLink to pick up the signal during programming.
Similar to this Canadian law, some U.S. gate operators are
designed to9time-out9in the same manner.
If you live in Canada or you are having difficulties
programming a gate operator by using the9Program-
ming HomeLink9procedures (regardless of where you
live), replace step two with the following:
NOTE:If programming a garage door opener or gate
operator, it is advised to unplug the device during the
9cycling9process to prevent possible overheating.
Press and hold the HomeLink button while you press
and release - every two seconds ((cycle() your hand-heldtransmitter button until the radio signal has success-
fully been accepted by HomeLink. (The message
TRAINED will appear on the HomeLink display.)
Proceed with the remaining steps under9Programming
HomeLink9to complete.
Using HomeLink
To operate, simply press and release the programmed
HomeLink button. Activation will now occur for the
trained device (i.e. garage door opener, gate operator,
security system, entry door lock, home/office lighting,
etc.). For convenience, the hand-held transmitter of the
device may also be used at any time. In the event that
there are still programming difficulties or questions,
contact HomeLink at:www.homelink.comor1-800-355-
3515.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111
3