spare tire location JEEP GRAND CHEROKEE 2004 WK / 3.G Owners Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 2004, Model line: GRAND CHEROKEE, Model: JEEP GRAND CHEROKEE 2004 WK / 3.GPages: 344, PDF Size: 6.09 MB
Page 99 of 344
TO MEMORY is set to YES) when the remote keyless
entry transmitter is used to unlock the door. Pressing the
STEP button when in this display will select ªYesº or
ªNo.º
Retrain Tire Sensors? (Available with TPM System
Only)
When this feature is selected, the TPM system will start
the retraining procedure (Refer to Training Procedure
below). Pressing the STEP button when in this display
will select ªYesº or ªNo.º Then, press the MENU button
to enter selection.
WARNING!
Death or serious injury can occur if magnetically
sensitive devices are exposed to this magnet. Mag-
nets can affect pacemakers.
NOTE:The tire pressure sensors must be retrained after
rotating the tires or replacing one or more sensors. If a
wheel rotation is not followed by the retrain procedure,
the system will not properly inform you of the correct
vehicle location for a low or high pressure tire.
The following describes how to use this feature:
1. Locate the training magnet under the spare tire
(shaped like a doughnut).
2. Press the MENU button until RETRAIN TIRE SEN-
SORS is displayed.
3. Press the STEP button to select YES to retrain TPM
sensor.
4. Press the MENU button to enter selection.
5. Display will read TRAIN LEFT FRONT TIRE.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99
3
Page 207 of 344
Tire Loading and Tire Pressure
Tire Placard Location
NOTE:Some vehicles have a ªTire and Loading Infor-
mationº placard located on the driver's side ªBº pillar.
Tire and Loading Information Placard
This placard tells you important information about the,
1) number of people that can be carried in the vehicle
2) the total weight your vehicle can carry
3) the tire size designed for your vehicle
4) the cold tire inflation pressures for the front, rear
and spare tires.
STARTING AND OPERATING 207
5
Page 219 of 344
and display SPARE SWAP DETECTED along with a
chime. This could take up to 10 minutes with vehicle
speed above 25 mph (40 km/h).
With the 4 Tire TPM System, if a road tire and wheel is
replaced by the spare, the TPM system will display TIRE
SENSOR BAD/MISSING. This is due to the spare tire not
being equipped with a tire pressure sensor. Once the road
tire is repaired and/or installed back on the vehicle with
the proper tire pressure the message will be removed.
This could take up to 10 minutes with vehicle speed
above 25 mph (40 km/h).
The tire pressure sensorsmustbe retrained following a
wheel rotation or sensor replacement. Refer to ªEVIC Ð
Retrain Tire Sensorsº in Section 3 for more information. It
is necessary to program the EVIC with the new sensor(s)
or the new position of each sensor as it is rotated to a
different corner of the vehicle.If a wheel rotation is not followed by the retrain proce-
dure, the system will not properly inform you of the
correct vehicle location of a low or high tire pressure.
General Information
This device complies with part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:
²This device may not cause harmful interference.
²This device must accept any interference received,
including interference that may cause undesired op-
eration.
The tire pressure sensors are covered under one of the
following licenses:
United States.....................KR5S120123
Canada........................2671-S120123
STARTING AND OPERATING 219
5
Page 235 of 344
WHAT TO DO IN EMERGENCIES
CONTENTS
mHazard Warning Flashers.................236
mIf Your Engine Overheats.................237
mChanging A Flat Tire....................238
NJack And Lug Wrench Locations...........238
NSpare Tire Location....................239NTire Changing Procedure................242
mJump Starting Procedure..................246
mEmergency Tow Hooks Ð If Equipped........248
mTowing A Disabled Vehicle................248
6
Page 239 of 344
WARNING!
²Always store the jack, lug wrench and spare, flat
or damaged tire securely in the proper place.
Never leave them loose in the vehicle where they
could become dangerous projectiles during a
quick stop or collision.
²The jack is designed to use as a tool for changing
tires only. The jack should not be used to lift the
vehicle for service purposes, unless suitable sup-
ports are placed under the vehicle as a safety
measure, The vehicle should be jacked on a firm
level surface only. Avoid ice or slippery areas.
Spare Tire Location
To Remove the Spare Tire
1. Open the liftgate.
2. Grasp the cover on both sides at the edge adjacent to
the carpet depressions and lift the cover to unlatch.The
cover may be placed forward to lean against the rear
WHAT TO DO IN EMERGENCIES 239
6
Page 244 of 344
5. Raise the vehicle by turning the jack handle clockwise
until the tire clears the ground.
WARNING!
Raising the vehicle higher than necessary can make
the vehicle less stable and cause an accident. It could
slip off the jack and hurt someone near it. Raise the
vehicle only enough to remove the tire.
6. Remove the lug nuts and wheel.
7. Position the spare wheel/tire on the vehicle and install
the lug nuts with the cone-shaped end toward the wheel.
Lightly tighten the nuts until they are equally snug, using
a crisscross pattern. To avoid the risk of forcing the
vehicle off the jack, do not tighten the nuts fully until the
vehicle has been lowered.
8. Lower the vehicle and remove the jack and wheel
blocks.
Rear Jacking Location
244 WHAT TO DO IN EMERGENCIES