light JEEP GRAND CHEROKEE 2005 WK / 3.G Owner's Guide

Multi-Function Control Lever
The multi-function control lever controls the operation of
the headlights, turn signals, headlight beam selection,
instrument panel light dimming, passing light, interior
courtesy/dome lights, and optional fog lights.
Battery Saver Feature—Exterior/Interior Lights
If the multi-function control lever is left in the interior
light position, parking light position, or the headlight
position when the ignition switch is moved to the OFF
position, the battery saver feature will automatically turn
off the exterior and interior lights after eight minutes.
Normal operation will resume when the ignition is
turned ON or when the headlight switch is turned to
another position.
Multi-Function Control Lever
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Headlights and Parking Lights
Turn the end of the multi-function control lever to the
first detent for parking light operation. Turn to the
second detent for headlight operation. Turn to the third
detent for “Auto” headlight operation (if equipped).
Automatic Headlight System — If Equipped
Turn the end of the multi-function control lever to the
third detent to activate the automatic headlight system.
This system performs two functions. With the engine
running and the multi-function control lever in the A
(Auto) position, the headlights will turn on and off based
on the surrounding light levels.
Headlights On Automatically With Wipers
If your vehicle is equipped with Automatic Headlights it
also has this customer programmable feature. When your
headlights are in the automatic mode, and the engine is
running, they will automatically turn on when the wiper
system is on.
If your vehicle is equipped with a “Rain Sensitive Wiper
System,” and it is activated, the headlights will automati-
cally turn on after the wipers complete five wipe cycles
within approximately 1 minute, and they will turn off
Headlight Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113
3

approximately four minutes after the wipers completely
stop. Refer to “Windshield Wipers and Washers” in this
section for more information
NOTE:When your headlights come on during the
daytime, the instrument panel lights will automatically
dim to the lower nighttime intensity. Refer to “Instru-
ment Panel and Interior Lights” below for setting the
instrument panel lights to full daytime intensity.
SmartBeams — If Equipped
The SmartBeam system provides increased forward light-
ing at night by automating high beam control through
the use of a digital camera mounted on the inside
rearview mirror. This camera detects vehicle specific light
and automatically switches from high beams to low
beams until the approaching vehicle is out of view.
To Activate
1. Select “Enable Auto HI Beams.” Refer to “EVIC —
Customer Programmable Features” in Section 4 of this
manual.
2. Turn the end of the multi-function control lever to the
A (Auto) headlight position.
NOTE:This system will not activate until the vehicle is
at or above 20 mph (32 km/h).
To Deactivate
1. Pull back on the muti-function control lever to manu-
ally deactivate the system (normal operation of high
beams).
2. Pull back on the multi-function control lever once
again to re-activate the system.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE:Broken, muddy, or obstructed headlights and
taillights of vehicles in the field of view will cause
headlights to remain on longer (closer to the vehicle).
Also, dirt, film, and other obstructions on the windshield
or camera lens will cause the system to function improp-
erly.
Instrument Panel and Interior Lights
When the multi-function control lever is in the parklight,
headlight, or A (Auto) position (if equipped), rotating the
center portion of the lever up and down will increase and
decrease the brightness (dimmer control) of the instru-
ment panel lights. Full daytime brightness on all elec-
tronic displays (odometer, overhead console, radio, and
Automatic Climate Control (if equipped) is obtained by
rotating the center portion of the control to the first
detent above the dimmer range. Rotating the control to
the second detent above the dimmer range turns the
interior lights on. Rotating the control to the “Off”
(extreme bottom) position disables all the interior lights,even when the doors and liftgate are open. While in the
“Off” position the instrument panel lighting is at the
lowest light level and may not be suitable for night
driving.
Daytime Running Lights — Canada Only
The headlights come on at a low intensity level whenever
the engine is running. The lights remain on until the
ignition switch is turned OFF or the parking brake is
engaged. The headlight switch must be used for normal
night time driving.
Lights-On Reminder
If the headlights or parking lights are on after the ignition
is turned OFF, a chime will sound when the driver’s door
is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115
3

Fog Lights — If Equipped
The fog light switch is located in the multi-
function control lever. To activate the fog lights,
turn on the park/turn lights, low beam headlights,
or “Auto” headlights and pull out the end of the multi-
function control lever. A light in the instrument cluster
shows when the fog lights are on.
NOTE:Turning on the high beam headlights turns off
the fog lights.
A front fog light is a lighting device providing illumina-
tion forward of the vehicle under conditions of fog, rain,
snow, or dust. Principally, the front fog light supplements
the lower beam of a standard headlight system.
NOTE:Proper aim and adjustments of the front fog
lights should be made to prevent excessive glare for other
drivers.
Turn Signals
Move the multi-function control lever up or down and
the arrows on each side of the instrument cluster will
flash to show proper operation of the front and rear turn
signal lights. You can signal a lane change by moving the
lever partially up or down.
High Beam Switch
Pull the multi-function control lever towards you to
switch the headlights to “High” beam. The “High Beam
Indicator Light” on the instrument cluster will illumi-
nate.Pull the multi-function control lever a second time to
switch the headlights to “Low” beam.
Passing Light
You can signal another vehicle with your headlights by
lightly pulling the multi-function control lever toward
the steering wheel. This will cause the headlights to turn
on at high beam and remain on until the lever is released.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Headlight Time Delay
There is also a feature that delays turning off the vehicle
lights for 30, 60, or 90 seconds after the ignition switch is
turned OFF. To activate the headlight delay, the multi-
function control lever must be rotated to the “Off”
position after the ignition switch is turned OFF. Only the
headlights will illuminate during this time. Refer to
“EVIC- Customer Programmable Features” in Section 4
to turn this feature “On/Off” or set the time interval.
WINDSHIELD WIPERS AND WASHERS
The front and rear wipers and washers are operated by a
switch in the right side control lever. Turn the end of the
control lever to select “Lo,” “Hi,” or one of the five speed
sensitive intermittent windshield wiper speeds. Refer to
“Speed Sensitive Intermittent Wiper System” in this
section. For information on the rear wiper and washer
refer to “Rear Window Features” in this section.NOTE:Always remove any build-up of snow that
prevents the windshield wiper blades from returning to
the OFF position. If the windshield wiper switch is
turned off and the blades cannot return to the OFF
position, damage to the wiper motor may occur.
Windshield Wiper/Washer Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117
3

WARNING!
Tilting the steering wheel column while the vehicle
is moving is dangerous. Without a stable steering
column, you could lose control of the vehicle and
have an accident. Adjust the tilting mechanism only
while the vehicle is stopped. Be sure it is locked
before driving.
TRACTION CONTROL — IF EQUIPPED
The Traction Control System monitors the amount of
wheel spin in each of the driven wheels. If wheel spin is
detected, the pressure to the brake system of the slipping
wheel(s) is modulated to provide enhanced acceleration.
The system operates at speeds typically encountered in
city traffic driving. 4WD models also include unique
logic in 4 HI or 4 LO (if equipped) to enhance off-road
capabilities.The “Traction Control Indicator Light,” located in the
instrument cluster, will flash when the Traction Control
System is active.
To turn the system OFF, press the switch, located below
the climate controls in the center stack, until the “Traction
Control Indicator Light” turns on and stays on. Also, a
Traction Control Indicator Light
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121
3

“TRACTION SYS DISABLED” message will be displayed
in the Electronic Vehicle Information Center (EVIC).
Refer to Section 4 of this manual.
To turn the system back ON, press the switch a second
time, until the “Traction Control Indicator Light” turns
off.When the Traction Control System has been turned off
using the switch, a feature of the system remains active.
This feature functions similar to a limited slip differential
and controls the wheel spin across an axle. If one wheel
on an axle is spinning faster than the other, the system
will apply the brake of the spinning wheel and allow
more engine torque to be applied to the wheel that is not
spinning.
NOTE:
•The “Traction Control Indicator Light” comes on mo-
mentarily each time the ignition switch is turned ON.
This will occur even if you used the switch to turn the
system OFF.
•Each time the ignition is turned ON, the Traction
Control System will be ON even if it was turned OFF
previously.
•The Traction Control System will make buzzing or
clicking sounds when it is active.
Traction Control Switch
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

There are two Electronic Vehicle Information Center
(EVIC) messages associated with the Traction Control
System. Refer to Section 4 of this manual.
Traction Sys Disabled
This message will be displayed if the Traction Control
System has been turned off using the switch, or if there is
a temporary condition that will will result in partial or no
Traction Control System function. The “Traction Control
Indicator Light” will be on when the system is disabled
or only partial function is allowed. The “TRACTION SYS
DISABLED” message and the “Traction Control Indicator
Light” being illuminated without the switch being de-
pressed is not an indication that service of the electronic
brake system is required.Service Elec Brake System
This message will be displayed if a condition exists that
may require servicing the electronic brake system. When
this message is displayed and the “Traction Control
Indicator Light” is on, there is a malfunction of the
Traction Control System. If the “SERVICE ELEC BRAKE
SYSTEM” message continues to be displayed after sev-
eral ignition cycles and the vehicle has been driven
several miles at speeds greater than 30 mph (48 km/h),
see your authorized dealer for service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123
3

ELECTRONIC STABILITY PROGRAM (ESP)— IF
EQUIPPED
WARNING!
ESP (Electronic Stability Program) cannot prevent
the natural laws of physics from acting on the
vehicle, nor can it increase the traction afforded. The
ESP cannot prevent accidents, including those re-
sulting from excessive speed in turns, or hydroplan-
ing. Only a safe, attentive, and skillful driver can
prevent accidents. The capabilities of an ESP-
equipped vehicle must never be exploited in a reck-
less or dangerous manner which could jeopardize
the user’s safety or the safety of others.
ESP (Electronic Stability Program) enhances directional
control and reduces driving wheel spin of the vehicle
under various driving conditions.ESP corrects for over/understeering of the vehicle by
applying brakes to the appropriate wheel. Engine torque
is also limited. The “ESP Indicator Light,” located in the
instrument cluster, starts to flash as soon as the tires lose
traction and the ESP system becomes active.ESP Indicator Light
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE