brake light JEEP GRAND CHEROKEE 2005 WK / 3.G Owners Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 2005, Model line: GRAND CHEROKEE, Model: JEEP GRAND CHEROKEE 2005 WK / 3.GPages: 408, PDF Size: 25.77 MB
Page 115 of 408
NOTE:Broken, muddy, or obstructed headlights and
taillights of vehicles in the field of view will cause
headlights to remain on longer (closer to the vehicle).
Also, dirt, film, and other obstructions on the windshield
or camera lens will cause the system to function improp-
erly.
Instrument Panel and Interior Lights
When the multi-function control lever is in the parklight,
headlight, or A (Auto) position (if equipped), rotating the
center portion of the lever up and down will increase and
decrease the brightness (dimmer control) of the instru-
ment panel lights. Full daytime brightness on all elec-
tronic displays (odometer, overhead console, radio, and
Automatic Climate Control (if equipped) is obtained by
rotating the center portion of the control to the first
detent above the dimmer range. Rotating the control to
the second detent above the dimmer range turns the
interior lights on. Rotating the control to the “Off”
(extreme bottom) position disables all the interior lights,even when the doors and liftgate are open. While in the
“Off” position the instrument panel lighting is at the
lowest light level and may not be suitable for night
driving.
Daytime Running Lights — Canada Only
The headlights come on at a low intensity level whenever
the engine is running. The lights remain on until the
ignition switch is turned OFF or the parking brake is
engaged. The headlight switch must be used for normal
night time driving.
Lights-On Reminder
If the headlights or parking lights are on after the ignition
is turned OFF, a chime will sound when the driver’s door
is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115
3
Page 121 of 408
WARNING!
Tilting the steering wheel column while the vehicle
is moving is dangerous. Without a stable steering
column, you could lose control of the vehicle and
have an accident. Adjust the tilting mechanism only
while the vehicle is stopped. Be sure it is locked
before driving.
TRACTION CONTROL — IF EQUIPPED
The Traction Control System monitors the amount of
wheel spin in each of the driven wheels. If wheel spin is
detected, the pressure to the brake system of the slipping
wheel(s) is modulated to provide enhanced acceleration.
The system operates at speeds typically encountered in
city traffic driving. 4WD models also include unique
logic in 4 HI or 4 LO (if equipped) to enhance off-road
capabilities.The “Traction Control Indicator Light,” located in the
instrument cluster, will flash when the Traction Control
System is active.
To turn the system OFF, press the switch, located below
the climate controls in the center stack, until the “Traction
Control Indicator Light” turns on and stays on. Also, a
Traction Control Indicator Light
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121
3
Page 122 of 408
“TRACTION SYS DISABLED” message will be displayed
in the Electronic Vehicle Information Center (EVIC).
Refer to Section 4 of this manual.
To turn the system back ON, press the switch a second
time, until the “Traction Control Indicator Light” turns
off.When the Traction Control System has been turned off
using the switch, a feature of the system remains active.
This feature functions similar to a limited slip differential
and controls the wheel spin across an axle. If one wheel
on an axle is spinning faster than the other, the system
will apply the brake of the spinning wheel and allow
more engine torque to be applied to the wheel that is not
spinning.
NOTE:
•The “Traction Control Indicator Light” comes on mo-
mentarily each time the ignition switch is turned ON.
This will occur even if you used the switch to turn the
system OFF.
•Each time the ignition is turned ON, the Traction
Control System will be ON even if it was turned OFF
previously.
•The Traction Control System will make buzzing or
clicking sounds when it is active.
Traction Control Switch
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 123 of 408
There are two Electronic Vehicle Information Center
(EVIC) messages associated with the Traction Control
System. Refer to Section 4 of this manual.
Traction Sys Disabled
This message will be displayed if the Traction Control
System has been turned off using the switch, or if there is
a temporary condition that will will result in partial or no
Traction Control System function. The “Traction Control
Indicator Light” will be on when the system is disabled
or only partial function is allowed. The “TRACTION SYS
DISABLED” message and the “Traction Control Indicator
Light” being illuminated without the switch being de-
pressed is not an indication that service of the electronic
brake system is required.Service Elec Brake System
This message will be displayed if a condition exists that
may require servicing the electronic brake system. When
this message is displayed and the “Traction Control
Indicator Light” is on, there is a malfunction of the
Traction Control System. If the “SERVICE ELEC BRAKE
SYSTEM” message continues to be displayed after sev-
eral ignition cycles and the vehicle has been driven
several miles at speeds greater than 30 mph (48 km/h),
see your authorized dealer for service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123
3
Page 124 of 408
ELECTRONIC STABILITY PROGRAM (ESP)— IF
EQUIPPED
WARNING!
ESP (Electronic Stability Program) cannot prevent
the natural laws of physics from acting on the
vehicle, nor can it increase the traction afforded. The
ESP cannot prevent accidents, including those re-
sulting from excessive speed in turns, or hydroplan-
ing. Only a safe, attentive, and skillful driver can
prevent accidents. The capabilities of an ESP-
equipped vehicle must never be exploited in a reck-
less or dangerous manner which could jeopardize
the user’s safety or the safety of others.
ESP (Electronic Stability Program) enhances directional
control and reduces driving wheel spin of the vehicle
under various driving conditions.ESP corrects for over/understeering of the vehicle by
applying brakes to the appropriate wheel. Engine torque
is also limited. The “ESP Indicator Light,” located in the
instrument cluster, starts to flash as soon as the tires lose
traction and the ESP system becomes active.ESP Indicator Light
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 126 of 408
than the other, the system will apply the brake of the
spinning wheel and allow more engine torque to be
applied to the wheel that is not spinning.
To improve the vehicle’s traction when driving with
snow chains, or starting off in deep snow, sand or gravel,
it may be desirable to switch off the ESP by pressing the
ESP switch.
With the ESP switched off, the engine torque reduction
and stability features are cancelled. Therefore, the en-
hanced vehicle stability offered by ESP is unavailable.
If the “ESP Indicator Light” begins to flash during
acceleration, ease up on the accelerator and apply as little
throttle as possible. Be sure to adapt your speed and
driving to the prevailing road conditions. When the “ESP
Indicator Light” is illuminated continuously, the ESP is
switched off. To return to the enhanced vehicle stability
offered by ESP, press the ESP switch (the “ESP IndicatorLight” in the instrument cluster goes out). Avoid spin-
ning one drive wheel. This may cause serious damage to
the drive train.
NOTE:
•The “ESP Indicator Light” comes on momentarily each
time the ignition switch is turned ON.
•Each time the ignition is turned ON, the ESP System
will be ON even if it was turned off previously.
•The ESP Control System will make buzzing or clicking
sounds when it is active.
There are two Electronic Vehicle Information Center
(EVIC) messages associated with the Electronic Stability
Control System. Refer to Section 4 of this manual.
ESP System Disabled
This message will be displayed if the ESP System has
been turned off using the switch, or if there is a tempo-
rary condition that will result in partial or no ESP
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 127 of 408
function. The “ESP Indicator Light” will be on when the
system is disabled or only partial function is allowed. The
“ESP SYSTEM DISABLED” message and the “ESP Indi-
cator Light” being illuminated without the switch being
depressed is not an indication that service of the elec-
tronic brake system is required.
Also, the “ESP SYSTEM DISABLED” message will be
present when the vehicle is shifted into 4WD LOW.
Service Elec Brake System
This message will be displayed if a condition exists that
may require servicing the electronic brake system. When
this message is displayed and the “ESP Indicator Light”
is on, there is a malfunction of the ESP System. If the
“SERVICE ELEC BRAKE SYSTEM” message continues to
be displayed after several ignition cycles and the vehicle
has been driven several miles at speeds greater than 30
mph (48 km/h), see your authorized dealer for service.CAUTION!
The manufacturer recommends towing with all four
wheels off the ground. Acceptable methods are to
tow the vehicle on a flatbed or with one end of the
vehicle raised and the other end on a towing dolly.
REAR PARK ASSIST SYSTEM— IF EQUIPPED
The Rear Park Assist System provides visual and audible
indications of the distance between the rear fascia and the
detected obstacle when backing up. Refer to the Warning
Section and Note Section for limitations of this system
and recommendations.
The Rear Park Assist System will remember the last
system state (enabled or disabled) from the last ignition
cycle when the ignition is changed to the RUN/ON
position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127
3
Page 134 of 408
ELECTRONIC SPEED CONTROL
When engaged, this device takes over accelerator opera-
tions at speeds greater than 25 mph (40 km/h) for 5.7L
engines, and 30 mph (48 km/h) for 3.7L/4.7L engines.
The controls are mounted on the steering wheel and
consist of ON·OFF, SET, RES·ACCEL, CANCEL, and
DECEL controls.
To Activate
Press the ON·OFF button to turn the system ON. To turn
the system OFF, press the ON·OFF button again. The
system should be turned OFF when not in use. The
CRUISE indicator light in the instrument cluster will
illuminate when the system is ON.
To Set at a Desired Speed
When the vehicle has reached the desired speed, press
and release the SET button. Release the accelerator and
the vehicle will operate at the selected speed.
To Deactivate
A soft tap on the brake pedal, normal braking, or pressing
the CANCEL button will deactivate the Speed Control
without erasing the memory. Pressing the ON·OFF to
turn the system OFF or turning off the ignition erases the
memory.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 164 of 408
INSTRUMENT CLUSTER DESCRIPTION
1. Speedometer
Indicates vehicle speed.
2. Brake Warning Light
The red BRAKE warning light will come on
when the ignition is first turned on, and stay on
briefly as a bulb check. If the bulb does not
come on during starting, have the bulb re-
paired promptly. If the light stays on longer, it may be an
indication that the parking brake has not been released.
If the light remains on when the parking brake is off, it
indicates a possible brake hydraulic system malfunction
or low fluid level. In this case, the light will remain on
until the cause is corrected. If a brake malfunction is
indicated, immediate repair is necessary and continued
operation of the vehicle in this condition is dangerous.3. Turn Signal Indicator Light
The arrow will flash with the exterior turn signal
when the turn signal lever is operated.
If the vehicle electronics sense that the vehicle has
traveled about one mile with the turn signals on, a chime
will sound to alert you to turn the signals off. If either
indicator flashes at a rapid rate, check for a defective
outside light bulb.
4. High Beam Indicator Light
Indicates that headlights are on high beam.
5. Malfunction Indicator Light
This light is part of an onboard diagnostic system
called OBD that monitors engine and automatic
transmission control systems. The light will illu-
minate when the key is in the ON position before engine
start. If the bulb does not come on when turning the key
from OFF to ON, have the condition checked promptly.
164 UNDERSTANDING YOUR INSTRUMENT PANEL
Page 165 of 408
Certain conditions such as a loose or missing gas cap,
poor fuel quality, etc. may illuminate the light after
engine start. The vehicle should be serviced if the light
stays on through several of your typical driving cycles. In
most situations the vehicle will drive normally and will
not require towing.
The Malfunction Indicator Light flashes to alert you to
serious conditions that could lead to immediate loss of
power or severe catalytic converter damage. The vehicle
should be serviced as soon as possible if this occurs. (See
page 313 for more information.)
6. Airbag Warning Light
This light turns on and remains on for 6 to 8
seconds as a bulb check when the ignition
switch is first turned ON. If the light is not on
during starting, stays on, or turns on while
driving, have the system inspected by an authorized
dealer as soon as possible.7. Anti-Lock Brake Warning Light
This light monitors the Anti-Lock Brake System.
The light will turn on when the ignition switch is
turned to the ON position and may stay on for as long as
four seconds.
If the ABS light remains on or turns on while driving, it
indicates that the Anti-Lock portion of the brake system
is not functioning and that service is required. However,
the conventional brake system will continue to operate
normally if the BRAKE warning light is not on.
If the ABS light is on, the brake system should be serviced
as soon as possible to restore the benefits of Anti-Lock
brakes. If the ABS light does not turn on when the
Ignition switch is turned to the ON position, have the
light inspected by an authorized dealer.
UNDERSTANDING YOUR INSTRUMENT PANEL 165
4