display JEEP GRAND CHEROKEE 2017 WK2 / 4.G Owner's Manual

Speed Warning — If Equipped
Push and release theupordown arrow button until the
Speed Warning Menu icon/title is highlighted in the
instrument cluster display. Push and release the OKbutton
to enter speed warning. Use the upordown arrow button
to select a desired speed, then push and release the OK
button to set the speed. The Speed Warning telltale will
display in the instrument cluster display, and a chime will
sound with a pop up warning message when the set speed
is exceeded.
Diesel Particulate Filter (DPF) Messages
This engine meets all required diesel engine emissions
standards. To achieve these emissions standards, your
vehicle is equipped with a state-of-the-art engine and
exhaust system. These systems are seamlessly integrated
into your vehicle and managed by the Powertrain Control
Module (PCM). The PCM manages engine combustion to
allow the exhaust system’s catalyst to trap and burn
Particulate Matter (PM) pollutants, with no input or inter-
action on your part.
WARNING!
A hot exhaust system can start a fire if you park over
materials that can burn. Such materials might be grass or
leaves coming into contact with your exhaust system. Do
not park or operate your vehicle in areas where your
exhaust system can contact anything that can burn.
Your vehicle has the ability to alert you to additional
maintenance required on your vehicle or engine. Refer to
the following messages that may be displayed on your
Instrument Cluster Display:
• Exhaust Filter Nearing Full Safely Drive at Highway
Speeds to Clear — This message will be displayed on
the instrument cluster display if the exhaust particulate
filter reaches 80% of its maximum storage capacity.
Under conditions of exclusive short duration and low
speed driving cycles, your diesel engine and exhaust
after-treatment system may never reach the conditions
required to cleanse the filter to remove the trapped PM.
If this occurs, the “Exhaust Filter XX% Full Safely Drive
at Highway Speeds to Remedy” message will be dis-
played in the instrument cluster display. If this message
is displayed, you will hear one chime to assist in alerting
you of this condition. By simply driving your vehicle at
142 GETTING TO KNOW YOUR INSTRUMENT PANEL

highway speeds for up to 20 minutes, you can remedy
the condition in the particulate filter system and allow
your diesel engine and exhaust after-treatment system to
cleanse the filter to remove the trapped PM and restore
the system to normal operating condition.
• Exhaust System Regeneration in Process Continue
Driving — This message indicates that the Diesel Par-
ticulate Filter (DPF) is self-cleaning. Maintain your cur-
rent driving condition until regeneration is completed.
• Exhaust System — Regeneration Completed — This
message indicates that the Diesel Particulate Filter (DPF)
self-cleaning is completed. If this message is displayed,
you will hear one chime to assist in alerting you of this
condition.
• Exhaust System Service Required - See Dealer — This
messages indicates regeneration has been disabled due
to a system malfunction. At this point the engine Pow-
ertrain Control Module (PCM) will register a fault code,
the instrument panel will display a MIL light.
CAUTION!
See your authorized dealer, as damage to the exhaust
system could occur soon with continued operation. •
Exhaust Filter Full — Power Reduced See Dealer —
This message indicates the PCM has derated the engine
to limit the likelihood of permanent damage to the
after-treatment system. If this condition is not corrected
and a dealer service is not performed, extensive exhaust
after-treatment damage can occur. To correct this condi-
tion it will be necessary to have your vehicle serviced by
your local authorized dealer.
NOTE: Failing to follow the oil change indicator, changing
your oil and resetting the oil change indicator by 0 miles
remaining will prevent the diesel exhaust filter from per-
forming it’s cleaning routine. This will shortly result in a
Malfunction Indicator Light (MIL) and reduced engine
power. Only an authorized dealer will be able to correct
this condition.
CAUTION!
See your authorized dealer, as damage to the exhaust
system could occur soon with continued operation.
Diesel Exhaust Fluid (DEF) Warning Messages
Your vehicle will begin displaying warning messages when
the DEF level reaches a driving range of approximately 500
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 143

miles. If the following warning message sequence is ig-
nored, your vehicle may not restart unless DEF is added
with in the mileage shown in the instrument cluster
display message.
•Engine Will Not Restart in XXXX mi DEF Low Refill
Soon — This message will display when DEF driving
range is less than 500 miles, DEF fluid top off is required
with in the displayed mileage. The message will be
shown in the display during vehicle start up with the
current allowed mileage and accompanied by a single
chime. The remaining mileage can be pulled up anytime
by way of the “Messages” list within the instrument
cluster display.
• Engine Will Not Restart in XXXX mi Refill DEF — This
message will display when DEF driving range is less
than 311 miles. It is also displayed at 249 miles, 186
miles, and 124 miles. Continuous Display starts at 124
miles. DEF fluid top off is required with in the displayed
mileage. The message will be shown in the display
during vehicle start up with an updated distance mile-
age, and it will be accompanied by a single chime.
Starting at 100 miles, remaining range will be continu-
ously displayed while operating the vehicle. Chimes will also accompany the 75, 50 and 25 mile remaining
distances. The DEF Low telltale will be on continuously
until DEF fluid is topped off.
• Engine Will Not Restart Refill DEF — This message
will display when the DEF driving range is less than 1
mile, DEF fluid top off is required or the engine will not
restart. The message will be shown in the instrument
cluster display during vehicle start up, and it will be
accompanied by a single chime. The DEF Low telltale
will be illuminated continuously until DEF fluid tank is
filled with a minimum of two gallons of DEF.
Diesel Exhaust Fluid (DEF) Fault Warning
Messages
There are different messages which are displayed if the
vehicle detects that the DEF system has been filled with a
fluid other than DEF, has experienced component failures,
or when tampering has been detected.
When the DEF system needs to be serviced the following
warnings will display:
• Service DEF System See Dealer — This message will
display when the fault is initially detected and each time
the vehicle is started. The message will be accompanied
by a single chime and the Malfunction Indicator Light.
144 GETTING TO KNOW YOUR INSTRUMENT PANEL

We recommend you drive to your nearest authorized
dealer and have your vehicle serviced immediately. If
not corrected in 30 miles, vehicle will enter the “Engine
Will not restart in XXXmi Service DEF See dealer”
warning stage and message.
• Incorrect DEF Detected See Dealer — This message will
display if the DEF system has detected the incorrect
fluid has been introduced to the DEF tank. The message
will be accompanied by a single chime. We recommend
you drive to your nearest authorized dealer and have
your vehicle serviced immediately. If not corrected in 30
miles, vehicle will enter the Engine Will not restart in
XXX mi Service DEF See dealer warning stage and
message.
• Engine Will Not Restart in XXX mi Service DEF See
Dealer — This message is first displayed if the fault
detected is not serviced after 30 miles of operation. It is
also displayed at 250 miles, 186 miles, and 124 miles.
System service is required within the displayed mileage.
The message will be displayed in the instrument cluster
display during vehicle start up with an updated distance
mileage, and it will be accompanied by a single chime.
Starting at 124 miles, remaining range will be continu-
ously displayed while operating the vehicle. Chimes will also accompany the 75, 5,0 and 25 mile remaining
distances. We recommend you drive to your nearest
authorized dealer and have your vehicle serviced imme-
diately.
• Engine Will Not Restart Service DEF System See
Dealer — This message will display if DEF system issue
detected is not serviced during the allowed period. Your
engine will not restart unless your vehicle is serviced by
your authorized dealer. This message will be displayed
when under 1 mile until engine will not start and each
time the vehicle is started, and will be continuously
displayed. The message will be accompanied by a single
chime. Your Malfunction Indicator Light will be continu-
ously illumined. We highly recommend you drive to
your nearest authorized dealer if the message appears
while engine is running.
•
Engine Will Not Start Service DEF System See Dealer—
This message will display when the fault detected is not
serviced after the Engine will not restart Service DEF
System See Dealer message is displayed on the next
subsequent restart. Your engine will not start unless you
vehicle is serviced by your authorized dealer. The mes-
sage will be accompanied by a single chime. Your
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 145

Malfunction Indicator Light will be continuously illumi-
nated. If the message appears and you can not start the
engine, we recommend you have your vehicle towed to
your nearest authorized dealer immediately.
NOTE:
• The gauge may take up to five seconds to update after
adding a gallon or more of Diesel Exhaust Fluid (DEF) to
the DEF tank. If you have a fault related to the DEF
system, the gauge may not update to the new level. See
your authorized dealer for service.
• The DEF gauge may also not immediately update after a
refill if the temperature of the DEF fluid is below 12F
(-11C). The DEF line heater will possibly warm up the
DEF fluid and allow the gauge to update after a period
of run time. Under very cold conditions, it is possible
that the gauge may not reflect the new fill level for
several drives.
Battery Saver On/Battery Saver Mode Message —
Electrical Load Reduction Actions — If Equipped
This vehicle is equipped with an Intelligent Battery Sensor
(IBS) to perform additional monitoring of the electrical
system and status of the vehicle battery. In cases when the IBS detects charging system failure, or
the vehicle battery conditions are deteriorating, electrical
load reduction actions will take place to extend the driving
time and distance of the vehicle. This is done by reducing
power to or turning off non-essential electrical loads.
Load reduction is only active when the engine is running.
It will display a message if there is a risk of battery
depletion to the point where the vehicle may stall due to
lack of electrical supply, or will not restart after the current
drive cycle.
When load reduction is activated, the message “Battery
Saver On” or “Battery Saver Mode” will appear in the
instrument cluster display.
These messages indicate the vehicle battery has a low state
of charge and continues to lose electrical charge at a rate
that the charging system cannot sustain.
NOTE:
•
The charging system is independent from load reduc-
tion. The charging system performs a diagnostic on the
charging system continuously.
• If the Battery Charge Warning Light is on it may indicate
a problem with the charging system. Refer to “Battery
Charge Warning Light” in “Warning And Indicator
146 GETTING TO KNOW YOUR INSTRUMENT PANEL

– Check what may be plugged in to power outlets +12V,115V AC, USB ports
– Check HVAC settings (blower, temperature)
– Check the audio settings (volume)
After a trip:
• Check if any aftermarket equipment was installed (ad-
ditional lights, upfitter electrical accessories, audio sys-
tems, alarms) and review specifications if any (load and
Ignition Off Draw currents).
• Evaluate the latest driving cycles (distance, driving time
and parking time).
• The vehicle should have service performed if the mes-
sage is still present during consecutive trips and the
evaluation of the vehicle and driving pattern did not
help to identify the cause.
TRIP COMPUTER
The Trip Computer is located in the instrument cluster
display. Push and release the up
ordownarrow
button until “Trip Info” is highlighted in the instrument
cluster display. Push and release the left
orright
arrow buttons to select Trip A or Trip B.
Trip A
•Shows the total distance traveled for Trip A since the last
reset.
• Shows the elapsed time traveled for Trip A since the last
reset.
Trip B
• Shows the total distance traveled for Trip B since the last
reset.
• Shows the elapsed time traveled for Trip B since the last
reset.
Elapsed Time
Shows the total elapsed time of travel since the last reset
when the ignition switch is in the ACC position. Elapsed
time will increment when the ignition switch is in the ON
or START position.
To Reset A Trip Function
Reset will only occur while a resettable function is selected
(highlighted). Push and hold the OKbutton to clear the
resettable function being displayed.
148 GETTING TO KNOW YOUR INSTRUMENT PANEL

WARNING/INDICATOR LIGHTS AND MESSAGES
IMPORTANT:The warning/indicator light switches on in
the instrument panel together with a dedicated message
and/or acoustic signal when applicable. These indications
are indicative and precautionary and as such must not be
considered as exhaustive and/or alternative to the infor-
mation contained in the Owner Manual, which you are
advised to read carefully in all cases. Always refer to the
information in this chapter in the event of a failure indica-
tion. All active telltales will display first, if applicable. The
system check menu may appear different based upon
equipment options and current vehicle status. Some tell-
tales are optional and may not appear.
Red Telltale Lights
Seat Belt Reminder Warning Light
Red Telltale
Light What It Means
Seat Belt Reminder Warning Light
When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight sec-
onds as a bulb check. During the bulb check, if the driver’s or passenger seat belt is unbuckled, a
chime will sound. After the bulb check or when driving, if the driver ’s seat belt remains unbuck-
led, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound.
Refer to “Occupant Restraint Systems” in “Safety” for further information.
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 149

Electronic Stability Control (ESC) OFF Indicator Light — If Equipped
Yellow TelltaleLight What It Means
Electronic Stability Control (ESC) OFF Indicator Light — If Equipped
This light indicates the Electronic Stability Control (ESC) is off.
Tire Pressure Monitoring System (TPMS) Warning Light
Yellow Telltale
Light What It Means
Tire Pressure Monitoring Indicator Light
The warning light switches on and a message is displayed to indicate that the tire pressure is
lower than the recommended value and/or that slow pressure loss is occurring. In these cases,
optimal tire duration and fuel consumption may not be guaranteed.
Should one or more tires be in the condition mentioned above, the display will show the indica-
tions corresponding to each tire in sequence.
IMPORTANT: Do not continue driving with one or more
flat tires as handling may be compromised. Stop the
vehicle, avoiding sharp braking and steering. Repair im-
mediately using the dedicated tire repair kit and contact
your authorized dealer as soon as possible. Each tire, including the spare (if provided), should be
checked monthly when cold and inflated to the inflation
pressure recommended by the vehicle manufacturer on the
vehicle placard or tire inflation pressure label. If your
vehicle has tires of a different size than the size indicated
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 161

Wait To Start Light — If Equipped
Yellow TelltaleLight What It Means
Wait To Start Light
The “Wait To Start” telltale will illuminate for approximately two seconds when the ignition is
turned to the RUN position. It’s duration may be longer based on colder operating conditions.
Vehicle will not initiate start until telltale is no longer displayed. Refer to “Starting Procedures”
in “Starting and Operating” for further information.
NOTE:
The “Wait To Start” telltale may not illuminate if the intake manifold temperature is
warm enough.
Low Diesel Exhaust Fluid (DEF) Indicator Light — If Equipped
Yellow Telltale Light What It Means
Low Diesel Exhaust Fluid (DEF) Indicator Light
The Low Diesel Exhaust Fluid (DEF) Indicator will illuminate if the vehicle is low on Diesel Ex-
haust Fluid (DEF). Refer to “Starting And Operating” for further information.
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 169

Adaptive Cruise Control (ACC) Set With Target Detected Light — If Equipped
Green TelltaleLight What It Means
Adaptive Cruise Control (ACC) Set With Target Detected Light — If Equipped
This light will turn on when the Adaptive Cruise Control is SET and the target vehicle is de-
tected. Refer to
Adaptive Cruise Control (ACC) — If Equipped in Starting And Operating for
further information.
LaneSense Indicator Light — If Equipped
Green Telltale Light What It Means
LaneSense Indicator Light
The LaneSense indicator is solid green when both lane markings have been detected and the sys-
tem is “armed” to provide visual warnings in the instrument cluster display and a torque warn-
ing in the steering wheel if an unintentional lane departure occurs. Refer to “LaneSense — If
Equipped
in “Starting And Operating” for further information.
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 173