change language JEEP PATRIOT 2020 Owner handbook (in English)

•A maximum of 2,000 entries per phone will
be downloaded and updated every time a
phone is connected to the Uconnect Phone.
•Depending on the maximum number of en-
tries downloaded, there may be a short delay
before the latest downloaded names can be
used. Until then, if available, the previously
downloaded phonebook is available for use.
•Only the phonebook of the currently con-
nected mobile phone is accessible.
•Either the mobile phone’s phonebook or the
mobile phone’s SIM card phonebook is
downloaded.
•This downloaded phonebook cannot be ed-
ited or deleted on the Uconnect Phone.
These can only be edited on the mobile
phone. The changes are transferred and
updated to Uconnect Phone on the next
phone connection.
Add Names To Your Uconnect Phonebook
NOTE:
Adding names to the Uconnect Phonebook
is recommended when the vehicle is not in
motion.To add names to the Uconnect phonebook
using Voice Commands:
1. Push the Phone
button to begin.
2. After the “Ready” prompt and the following
beep, say “Phonebook New Entry.”
3. When prompted, say the name of the new
entry. Use of long names helps the Voice
Command and it is recommended. For ex-
ample, say “Robert Smith” or “Robert” in-
stead of “Bob.”
4. When prompted, enter the number designa-
tion (e.g., “Home,” “Work,” “Mobile,” or
“Other”). This will allow you to store multiple
numbers for each phonebook entry, if de-
sired.
5. When prompted, recite the phone number
for the phonebook entry that you are adding.
After you are finished adding an entry into the
phonebook, you will be given the opportunity to
add more phone numbers to the current entry or
to return to the main menu.The Uconnect Phone will allow you to enter up
to 32 names in the phonebook with each name
having up to four associated phone numbers
and designations. Each language has a sepa-
rate 32 name phonebook accessible only in that
language. In addition, if equipped and sup-
ported by your phone, Uconnect Phone auto-
matically downloads your mobile phone’s
phonebook.
Edit Uconnect Phonebook Entries
NOTE:
Editing phonebook entries is recommended
when the vehicle is not in motion. Automatic
downloaded phonebook entries cannot be
deleted or edited.
•Push the Phone
button to begin.
•After the “Ready” prompt and the following
beep, say “Phonebook Edit.”
•You will then be asked for the name of the
phonebook entry that you wish to edit.
•Next, choose the number designation (home,
work, mobile, or other) that you wish to edit.
70

and hold status of the two calls have switched.
Only one call can be placed on hold at a time.
Conference Call
When two calls are in progress (one active and
one on hold):
1. Push and hold the Phone
button until you
hear a double beep, indicating that the two
calls have been joined into one conference
call.
Three-Way Calling
To initiate three-way calling, push the Voice
Command
button while a call is in progress,
and make a second phone call, as described
under “Making a Second Call While Current Call
is in Progress.” After the second call has estab-
lished, push and hold the Phone
button until
you hear a double beep, indicating that the two
calls have been joined into one conference call.
Call Termination
To end a call in progress:
1. Momentarily push the Phone
button.
•Only the active call(s) will be terminated
and if there is a call on hold, it will become
the new active call. If the active call isterminated by the phone far end, a call on
hold may not become active automatically.
This is cell phone-dependent.
2. To bring the call back from hold, push and
hold the Phone
button until you hear a
single beep.
Redial
To redial the last number called from your
mobile phone using Voice Command:
1. Push the Phone
button to begin.
2. After the “Ready” prompt and the following
beep, say “Redial.”
•The Uconnect Phone will call the last num-
ber that was dialed from your mobile
phone.
NOTE:
This may not be the last number dialed from
the Uconnect Phone.
Call Continuation
Call continuation is the progression of a phone
call on the Uconnect Phone after the vehicle
ignition has been switched to OFF. Call continu-ation functionality available on the vehicle can
be any one of three types:
1. After the ignition is switched to OFF, a call
can continue on the Uconnect Phone either
until the call ends, or until the vehicle battery
condition dictates cessation of the call on the
Uconnect Phone and transfer of the call to
the mobile phone.
2. After the ignition is cycled to OFF, a call can
continue on the Uconnect Phone for a cer-
tain duration, after which the call is automati-
cally transferred from the Uconnect Phone to
the mobile phone.
3. An active call is automatically transferred to
the mobile phone after the ignition is cycled
to OFF.
Uconnect Phone Features
Language Selection
To change the language that the Uconnect
Phone is using:
•Push the Phone
button to begin.
73

Disc Mode
To switch to the disc mode, say “Disc.” In this
mode, you may say the following commands:
•“Track” (#) (to change the track)
•“Next Track” (to play the next track)
•“Previous Track” (to play the previous track)
•“Main Menu” (to switch to the main menu)
USB Mode
To switch to USB mode, say “USB.” In this
mode, you may say the following commands:
•“Next Track” (to play the next track)
•“Previous Track” (to play the previous track)
•“Play” (to play an Artist Name, Playlist Name,
Album Name, Track Name, etc.)
Bluetooth Streaming (BT) Mode
To switch to Bluetooth Streaming (BT) mode,
say “Bluetooth Streaming.” In this mode, you
may say the following commands:
•“Play” (to play the current track)
•“Pause” (to pause the current track)
•“Next Track” (to play the next track)•“Previous Track” (to play the previous track)
Memo Mode
To switch to the voice recorder mode, say
“Memo.” In this mode, you may say the follow-
ing commands:
•“New Memo” (to record a new memo) —
During the recording, you may push the
Voice Command
button to stop recording.
You proceed by saying one of the following
commands:
– “Save” (to save the memo)
– “Continue” (to continue recording)
– “Delete” (to delete the recording)
•“Play Memos” (to play previously recorded
memos) — During the playback you may
push the Voice Command
button to stop
playing memos. You proceed by saying one
of the following commands:
– “Repeat” (to repeat a memo)
– “Next” (to play the next memo)
– “Previous” (to play the previous memo)
– “Delete” (to delete a memo)
– “Delete All” (to delete all memos)System Setup
To switch to system setup, you may say one of
the following:
•“Change to system setup”
•“Main menu system setup”
•“Switch to system setup”
•“Change to setup”
•“Main menu setup” or
•“Switch to setup”
In this mode, you may say the following com-
mands:
•“Language English”
•“Language French”
•“Language Spanish”
•“Language Dutch”
•“Language Deutsch”
•“Language Italian”
•“Tutorial”
•“Voice Training”
87