light JEEP RENEGADE 2014 1.G Repair Manual

TOWING TRAILERS
TOW HOOK SETUP
128) 129)
Instructions for using the
removable ball head tow
bar
IMPORTANT Before setting off,check
the correctlockingof the removable
ball head tow bar, as follows:
❒the green mark of the knob must
coincide with the green mark on the
tow bar;
❒the knob is in the stop position on
the tow bar (without slot);
❒locked lock and key removed. The
knob cannot be removed;
❒ball head bar firmly secured to the
housing pipe. Check by shaking with a
hand.
The fitting procedure must be repeated
if any of the requirements are not met.
If even only one of the requirements
is not met the tow hookmust notbe
used, since there is risk of causing
accidents. Contact a Jeep Dealership.
The ball head tow bar can be
fitted/removed manually, without
requiring specific equipment.
IMPORTANT Never use vehicles or
work tools: the mechanism may be
damaged.IMPORTANT Never unlock in the case
of trailer attached to the vehicle or
with rack fitted.
IMPORTANT When driving without
trailer (or without rack), the ball head
tow bar must be removed and the
closing plug must always be inserted in
the housing pipe. This applies
particularly if, due to the bar, the
visibility of the number plate or of the
lighting system is reduced.
117

IN AN EMERGENCY
A punctured tyre or a burnt-out bulb?
At times, a problem may interfere
with our journey.
The pages on emergencies can help
you to deal with critical situations
independently and with calm.
In an emergency we recommend that
you call the freephone number found in
the Warranty Booklet.
It is also possible to call the national or
international universal freephone
number to search for the nearest
Dealership.HAZARD WARNING LIGHTS...........124
REPLACING A BULB ......................124
REPLACING FUSES........................130
CHANGING A WHEEL ...................135
TIREKIT ...........................................139
JUMP STARTING ............................141
FUEL CUT-OFF SYSTEM ................143
AUTOMATIC TRANSMISSION
GEAR LEVER UNLOCKING.............143
TOWING THE VEHICLE ..................145
BROKEN-DOWN VEHICLE
TOWING .........................................146
123

HAZARD WARNING
LIGHTS
CONTROL
Press button fig. 105 to switch the
lights on/off.
When the hazard warning lights are on,
the
andwarning lights flash.
IMPORTANT The use of hazard warning
lights is governed by the highway
code of the country you are driving in:
comply with legal requirements.
Emergency braking
In the event of an emergency braking
the hazard warning lights switch on
automatically as well as warning lights
andin the instrument panel.
The lights switch off automatically when
emergency braking ceases.
REPLACING A BULB
133) 134) 135)52)
GENERAL
INSTRUCTIONS
❒Before replacing a bulb check the
contacts for oxidation;
❒replace blown bulbs with others of
the same type and power;
❒after replacing a headlight bulb,
always check its alignment;
❒when a light is not working, check
that the corresponding fuse is intact
before replacing the bulb. For the
location of fuses, refer to the paragraph
“If a fuse blows” in this chapter.IMPORTANT When the weather is cold
or damp or after heavy rain or washing,
the surface of headlights or rear lights
may steam up and/or form drops of
condensation on the inside. This is
a natural phenomenon due to the
difference in temperature and humidity
between the inside and the outside
of the glass which does not indicate a
fault and does not compromise the
normal operation of lighting devices.
The mist disappears quickly when the
lights are turned on, starting from
the centre of the diffuser, extending
progressively towards the edges.
105J0A0050C
124
IN AN EMERGENCY

BulbsType Power
Front side lights/Daytime running lights (DRL) P21/5W 21/5 W
Rear side lightsP21W 21 W
Main beam/dipped beam headlights (halogen) H4 60/55 W
Main beam/dipped beam headlights (Xenon gas discharge) D5S 25 W
Front direction indicatorsPY21W 21 W
Rear direction indicatorsW16W 16 W
Side direction indicators (front and on door mirror) WY5W 5 W
3rd brake lightLED –
Number plateW5W 5 W
Fog lightsH11 55 W
Rear fog lightW16W 16 W
Reverse lightW16W 16 W
Front courtesy lightsC5W 5 W
Front roof lights (sun visors)C5W 5 W
Rear roof light (versions without sun roof) C5W 5 W
Rear roof lights (versions with sun roof) C5W 5 W
Luggage compartment roof lights W5W 5 W
Glove compartment lightW5W 4 W
125

CHANGING AN EXTERIOR
LIGHT
Front upper light cluster
(main beam/dipped halogen
headlights)
To replace the bulb, proceed as follows:
❒working from inside the engine
compartment, remove cover A fig. 106,
using the dedicated tab;
❒turn the bulb and bulb holder
assembly B fig. 107 anticlockwise and
then remove it outwards;❒remove, outwards, the bulb and bulb
holder assembly C fig. 108,
disconnecting it from connector D;
❒install the new bulb and bulb holder
assembly, ensuring that it is locked
correctly;
❒then insert the bulb and bulb holder
unit in its housing and turn it clockwise,
making sure that it is locked correctly.
IMPORTANT Only replace the bulb
when the engine is off. Also ensure that
the engine is cold, to prevent the risk
of burns.
Front upper light cluster
(main beam/dipped Xenon
gas discharge headlights)
For replacing these bulbs, contact
a Jeep Dealership.
Front lower light cluster
Side light/daytime running lights (DRLs)
and front direction indicators
To replace the bulbs proceed as
follows:
❒steer the wheels completely;
❒using the screwdriver, undo screws A
fig. 109 and remove flap B;
❒remove electrical connectors C fig.
110;
106J0A0260C
107J0A0261C
108J0A0414C
109J0A0211C
110J0A0306C
126
IN AN EMERGENCY

❒turn anticlockwise (on the left device)
or clockwise (on the right device) and
remove the bulb and bulb holder
assemblies fig. 111: D = side
lights/daytime running lights (DRLs), E =
direction indicators;
❒replace the blown bulb: to remove
the bulb, press on it gently (1 fig. 112)
and at the same time turn it
anticlockwise (2);❒insert the new bulb, by pressing it fig.
112 and turning it clockwise, making
sure that it locks correctly;
❒then insert the bulb and bulb holder
units in their respective housings and
turn them anticlockwise (right side) and
clockwise (left side), ensuring that
they are locked correctly;
❒reconnect the electrical connectors;
❒finally, refit flap B fig. 109, completely
tightening fixing screws A.
Fog lights
To replace the bulbs proceed as
follows:
❒steer the wheels completely;
❒using the screwdriver, undo screws A
fig. 113 and remove flap B;
❒using tab C fig. 114, remove
electrical connector D;❒turn the bulb and bulb holder
assembly E fig. 114 anticlockwise and
then replace the bulb;
❒fit the new bulb and bulb holder
assembly, ensuring that it locks
correctly;
❒reconnect the electrical connector;
❒finally, refit flap B fig. 113, completely
tightening fixing screws A.
Side direction indicators
Side direction indicators on door
mirrors
(where provided)
For bulb replacement, contact a Jeep
Dealership.
Rear upper light cluster
This contains the bulbs for the side
lights, brake lights and direction
indicators.
111J0A0263C
112J0A0264C
113J0A0211C
114J0A0301C
127

❒open the tailgate;
❒working at the point indicated by the
arrow, remove flap A fig. 115;
❒unscrew fixing device B fig. 116;
❒disconnect the electrical connector,
working on device C;
❒remove the rear light cluster,
outwards as indicated in fig. 117;
❒undo the four fixing screws D fig. 118
and remove the bulb holder unit;❒replace the bulb concerned (fig. 119:
E/G = brake lights, F = direction
indicators) (E and G bulbs always
switch on together);
❒fit the new bulb, making sure it is
correctly locked;
❒refit the bulb holder unit correctly on
the rear light cluster, completely
tightening the four fixing screws;
❒reposition the rear light cluster on the
vehicle;❒screw the rear light cluster fixing
device into position completely and
reconnect the electrical connector;
❒refit flap A fig. 115, ensuring that it
locks correctly;
❒finally, close the tailgate.
Rear lower light cluster
These contain the rear fog light bulbs
(left side) and reversing light bulbs (right
side).
To replace the bulbs proceed as
follows:
❒using the screwdriver, undo screws A
fig. 120 and B and remove flap C;
❒upper screw A is easy to access,
whereas for lower screw B it is
necessary to incline the blade of the
screwdriver appropriately as illustrated
in fig. 121;
115J0A0113C
116J0A0269C
117J0A0316C
118J0A0268C
119J0A0270C
128
IN AN EMERGENCY
To replace the bulbs proceed as
follows:

❒turn bulb holder D fig. 122
anticlockwise and replace the bulb
concerned;
❒fit the new bulb, making sure it is
correctly locked;
❒refit the bulb holder in its housing and
turn it clockwise, making sure that it
locks correctly;
❒refit flap C correctly, completely
tightening the screws.
3rd brake light
The 3rd brake lights are LED-based. To
replace them, contact a Jeep
Dealership.
Number plate lights
To replace the bulbs proceed as
follows:
❒remove the lenses A fig. 123;
❒rotate the bulb holder anticlockwise
and remove the bulbs;❒insert the new bulbs, making sure
that they are locked correctly in the
bulb holders;
❒finally, refit the lenses.
120J0A0212C
121J0A0213C
122J0A0302C
123J0A0444C
129

WARNING
133)Before replacing the bulb, wait for the
exhaust ducts to cool down: RISK OF
BURNS!
134)Changes or repairs to the electrical
system carried out incorrectly and without
due consideration for the technical
specifications of the system may lead to
malfunctioning and generate a fire hazard.
135)Halogen bulbs contain pressurised
gas. If they break, glass fragments could fly
everywhere.
WARNING
52)Halogen bulbs must be handled by
holding the metallic part only. Touching the
transparent part of the bulb with your
fingers may reduce the intensity of the
emitted light and even reduce the lifespan
of the bulb. In the case of accidental
contact, rub the lamp with a cloth and
spirit and leave to dry.
REPLACING FUSES
INTRODUCTION
136) 137) 138) 139) 140)
53) 54)
Fuse extracting pliers
To replace a fuse, use the pliers hooked
to the engine compartment fuse box
cover (see fig. 124).
FUSE LOCATION
Fuses are grouped together in four fuse
boxes located in the engine
compartment, under the dashboard
and inside the luggage compartment.
ENGINE COMPARTMENT
FUSE BOX
The fuse box is located by the side of
the battery fig. 125.
Releasing fixing screw and
removing fuse box cover
Proceed as follows:
❒fully tighten screw A fig. 126, using
the dedicated screwdriver provided;
124J0A0250C
125J0A0117C
130
IN AN EMERGENCY

LUGGAGE COMPARTMENT FUSE BOXESfig. 129
NOTE The configuration of the luggage compartment varies in accordance with the equipment on the vehicle.
Fuse box no. 1
DEVICES FUSE AMPERE
HI-FI system F2 20
Electric sun roof F3 20
Front seat electric lumbar adjustment (driver guide) F4 7,5
Electric front seat adjustment (driver side) F5 30
Electric front seat adjustment (driver side and passenger side) F6 7,5
Electric front seat lumbar adjustment (driver side and passenger
side)F7 30
Electrical front seat heating F8 20
The fuse box also has a 20 A protective fuse for the sun roof curtain.
Fuse box no. 2
DEVICES FUSE AMPERE
External trailer lighting control unit F1 10
External lighting control unit (left side) F5 15
External lighting control unit (right side) F6 15
134
IN AN EMERGENCY