lights JEEP RENEGADE 2017 1.G Owners Manual

FRONT VIEW
Front View
1 — Headlights
2 — Engine Compartment
3 — Windshield4 — Doors
5 — Exterior Mirrors
6 — Wheels
10 GRAPHICAL TABLE OF CONTENTS

REAR VIEW
Rear View
1 — Rear Lights
2 — Rear Windshield Wiper
3 — Liftgate
2
GRAPHICAL TABLE OF CONTENTS 11

▫Keyless Enter-N-Go — Passive Entry — If
Equipped .............................32
▫ Dead Lock Device — If Equipped ............36
▫ Child Locks ...........................37
 SEATS ................................38
▫ Manual Front Seats ......................38
▫ Power Adjustment (Front) — If Equipped ......39
▫ Heated Seats — If Equipped ................41
▫ Rear Seats ............................42
 HEAD RESTRAINTS ......................46
▫ Front Head Restraints ....................46
▫ Rear Head Restraints .....................47
 STEERING WHEEL .......................48
▫ Tilt/Telescoping Steering Column ............48
▫ Heated Steering Wheel — If Equipped .........48
 MIRRORS ..............................49
▫ Inside Day/Night Mirror ..................49 ▫
Auto Dimming Mirror — If Equipped .........49
▫ Outside Mirrors ........................50
▫ Folding Mirror .........................51
▫ Heated Mirrors — If Equipped .............51
 EXTERIOR LIGHTS .......................52
▫ Headlights ............................52
▫ Daytime Running Lights (DRL) — If Equipped . .52
▫ High Beams ...........................52
▫ Flash-To-Pass ..........................53
▫ Automatic Lighting — If Equipped ..........53
▫ Automatic High Beam Headlamp Control — If
Equipped .............................54
▫ Parking Lights .........................54
▫ Headlight Delay ........................54
▫ Front Fog Lights — If Equipped .............55
▫ Turn Signals ...........................55
 INTERIOR LIGHTS .......................56
16 GETTING TO KNOW YOUR VEHICLE

▫Courtesy Lights .........................56
▫ Internal Compartment Lights ...............60
▫ Cargo Area Lights .......................61
 WIPERS AND WASHERS ...................61
▫ Front Wiper Operation ....................62
▫ Rain Sensing Wipers — If Equipped ..........62
▫ Rear Wiper Operation ....................64
▫ Windshield Wiper De-Icer — If Equipped ......65
 CLIMATE CONTROLS .....................66
▫ Air Outlet And Diffuser Locations — Passenger
Compartment ..........................66
▫ Manual Climate Controls Overview ...........67
▫ Automatic Climate Control Overview .........72
▫ Operating Tips .........................80
 WINDOWS .............................83
▫ Power Window Controls ..................83
▫ Auto-Down Feature .....................84 ▫
Auto-Up Feature With Auto-Reverse Protection — If
Equipped .............................84
▫ Reset Auto-Up ..........................84
▫ Wind Buffeting .........................85
 MY SKY SUN ROOF — IF EQUIPPED .........85
▫ Removable Roof — If Equipped .............85
▫ Power My Sky — If Equipped ..............86
▫ Removing And Installing Panels .............87
▫ Bag For Housing Panels — If Equipped ........93
▫ Emergency Open/Close ...................95
▫ Wind Buffeting .........................96
 HOOD ................................96
▫ To Open The Hood ......................96
▫ To Close The Hood ......................98
 LIFTGATE .............................99
▫ Opening ..............................99
▫ Closing ............................ .101
3
GETTING TO KNOW YOUR VEHICLE 17

To Unlock The Doors And Liftgate
Push the interior door unlock button on the door panel.
Push and release the unlock button on the key fob once to
unlock the driver’s door or twice within five seconds to
unlock all doors and the liftgate.
All doors can be programmed to unlock on the first push of
the unlock button. Refer to “Uconnect Settings” in “Multi-
media” for further information.The turn signal lights will flash to acknowledge the unlock
signal. The illuminated entry system will be activated.
1st Push Of Key Fob Unlock Button
This feature lets you program the system to unlock either
the driver’s door or all doors on the first push of the unlock
button on the key fob. To change the current setting, refer
to “Uconnect Settings” in “Multimedia” for further infor-
mation.
NOTE:
If the vehicle is equipped with Passive Entry, refer
to “Keyless Enter-N-Go — Passive Entry” located in
“Doors” in “Getting To Know Your Vehicle” for further
information.
To Lock The Doors And Liftgate
Push and release the lock button on the key fob to lock all
doors and liftgate.
The turn signal lights will flash and the horn will chirp to
acknowledge the signal. Refer to “Uconnect Settings”
located in “Multimedia” for further programmable infor-
mation.
If the vehicle is equipped with Passive Entry, refer to
“Keyless Enter-N-Go — Passive Entry” located in “Doors”
in “Getting To Know Your Vehicle” for further information.
Key Fob Emergency Key Release
1 — Emergency Key Release Button
2 — Emergency Key 20 GETTING TO KNOW YOUR VEHICLE

remain armed when the battery is reconnected; the exterior
lights will flash, and the horn will sound. If this occurs,
disarm the vehicle security alarm.
Disabling
To completely disable the alarm (e.g. in the case of long
inactivity of the car), lock the doors by turning the vehicle
key in the exterior door lock cylinder.
NOTE:If the batteries in the key fob discharge in the event
of a failure to the system or to switch off the alarm, place
the ignition in the ON/RUN position.
DOORS
Manual Door Locks
To lock each door, rotate the door lock button on each door
trim panel forward. To unlock the doors, pull the inside
door handle to the first detent or rotate the door lock
button until the lock symbol is no longer visible.
If the lock symbol is visible when the door is shut, the door
will lock. Therefore, make sure the key fob is not inside the
vehicle before closing the door. Locking/Unlocking Doors From Outside
With the doors closed, insert the key blade into the driver
exterior door lock cylinder and turn to the right to lock the
driver’s door.
To unlock the driver ’s door, insert the key blade into the
driver exterior door lock cylinder and turn to the left to
unlock the driver’s door.
NOTE:
The manual lock knob unlocks each individual
door separately.
Manual Door Lock
30 GETTING TO KNOW YOUR VEHICLE

WARNING!(Continued)
•Seats should be adjusted before fastening the seat
belts and while the vehicle is parked. Serious injury
or death could result from a poorly adjusted seat belt.
• Do not ride with the seatback reclined so that the
shoulder belt is no longer resting against your chest.
In a collision you could slide under the seat belt,
which could result in serious injury or death.
CAUTION!
Do not place any article under a power seat or impede
its ability to move as it may cause damage to the seat
controls. Seat travel may become limited if movement
is stopped by an obstruction in the seat’s path.
Power Lumbar Adjustment— If Equipped
Push the switch forward or rearward to increase or de-
crease the lumbar support. Push the switch upward or
downward to raise or lower the lumbar support. NOTE:
Power seat adjustments are only allowed when the
ignition device is turned to ON, and for about 30 minutes
after it is turned to OFF. The seats can also be moved after
opening/closing the doors for about 30 minutes, locking or
unlocking the doors, or switching on of the front courtesy
lights.
Heated Seats — If Equipped
The heated seat switches are located on the instrument
panel.
You can choose between two heating levels:
• Push the heated seat button
once to turn the HI
setting on.
• Push the heated seat buttona second time to turn
the LO setting on.
• Push the heated seat buttona third time to turn the
heating elements off.
If the HI-level setting is selected, the system will automati-
cally switch to LO-level after approximately 145 minutes of
continuous operation. At that time, the display will change
from HI to LO, indicating the change. The LO-level setting
will turn off automatically after approximately 60 minutes.
3
GETTING TO KNOW YOUR VEHICLE 41

EXTERIOR LIGHTS
Headlights
The headlight switch is located on the left side of the instrument
panel. The headlight switch controls the operation of the head-
lights, side marker lights, daytime running lights, fog lights and
the dimming of the instrument cluster and interior lighting.
Turning on the headlights will illuminate the instrument
cluster and the controls located on the instrument panel.
Daytime Running Lights (DRL) — If Equipped
The Daytime Running Lights (DRLs) will turn on when the
engine is started and remain on unless the headlights are
turned on or the engine is shut off.
The DRLs will be disabled during turn signal operation
and resume operation when the turn signal operation has
ended.
High Beams
To turn on the high beam headlights, push the turn signal
lever forward (toward the front of the vehicle) and an
indicator will illuminate in the cluster. To turn off the high
beams, pull the turn signal lever rearward (toward the rear
of the vehicle).
Headlight Switch
1 — Rotate Headlight Switch
2 — Ambient Light Dimmer
3 — Instrument Panel Dimmer
4 — Push Fog Light Switch 52 GETTING TO KNOW YOUR VEHICLE

NOTE:The headlights must be on for the high beams to
activate.
Flash-To-Pass
You can signal another vehicle with your headlights by
lightly pulling the multifunction lever toward you. This
will cause the headlights to turn on at high beam and
remain on until the lever is released.
Automatic Lighting — If Equipped
Turn the headlight switch to the AUTO position.
When the automatic headlights are enabled, the headlight
time delay is active. After the ignition is placed in the OFF
position, the headlights will automatically turn off after the
time is set by Uconnect Settings.
Refer to “Headlight Delay” in this section for more infor-
mation.
NOTE: The engine must be running before the headlights
will come on in the automatic mode.
Light Sensor
The light sensor is equipped with an infrared LED, located
on the windshield. It detects changes in light intensity
outside the vehicle, based on the sensitivity of light set by
using the menu on the display or on the Uconnect system.
The higher the sensitivity, the lesser the amount of external
light required for controlling the lighting.
High Beam And Turn Signal Controls
3
GETTING TO KNOW YOUR VEHICLE 53

Automatic High Beam Headlamp Control — If
Equipped
The Automatic High Beam Headlamp Control system
provides increased forward lighting at night by automat-
ing high beam control through the use of a digital camera
mounted on the inside rearview mirror. This camera de-
tects vehicle specific light and automatically switches from
high beams to low beams until the approaching vehicle is
out of view.
NOTE:
•The Automatic High Beam Headlamp Control can be
turned on or off using the Uconnect System. Refer to
“Uconnect Settings” in “Multimedia” for further infor-
mation.
• Broken, muddy, or obstructed headlights and taillights
of vehicles in the field of view will cause headlights to
remain on longer (closer to the vehicle). Also, dirt, film,
and other obstructions on the windshield or camera lens
will cause the system to function improperly.
Parking Lights
From the O (off) position, rotate the headlight switch to the
first detent (parking position) to turn on the parking lights.
The parking light indicator in the instrument cluster will
illuminate.
Headlight Delay
This feature provides the safety of headlight illumination
for up to 90 seconds when leaving your vehicle in an unlit
area.
The time delay of the headlights is programmable between
0, 30, 60 and 90 seconds. Refer to “Uconnect Settings” in
“Multimedia” for further information.
Headlight Delay Activation
To activate the delay feature, place the ignition in the OFF
position while the headlights are still on. Then, turn off the
headlights within two minutes. The delay interval begins
when the headlight switch is turned off from the “Low-
beam” position.
If the headlight switch is in AUTO position and headlights
were on before the ignition is OFF, the delay interval begins
automatically.
54 GETTING TO KNOW YOUR VEHICLE