wheel JEEP WAGONEER 2022 User Guide
[x] Cancel search | Manufacturer: JEEP, Model Year: 2022, Model line: WAGONEER, Model: JEEP WAGONEER 2022Pages: 428, PDF Size: 12.99 MB
Page 325 of 428
W $ 5N ,N *
Do not attempt to change a tire on the side of
the vehicle close to moving traffic. Pull far
enough off the road to avoid the danger of
being hit when operating the jack or changing
the wheel.
Being under a jacked-up vehicle is dangerous.
The vehicle could slip off the jack and fall on
you. You could be crushed. Never put any part
of your body under a vehicle that is on a jack. If
you need to get under a raised vehicle, take it to
a service center where it can be raised on a lift.
Never start or run the engine while the vehicle
is on a jack.
The jack is designed to be used as a tool for
changing tires only. The jack should not be
used to lift the vehicle for service purposes.
The vehicle should be jacked on a firm level
surface only. Avoid ice or slippery areas.
WARNING!
Do not attempt to change a tire on the side of
the vehicle close to moving traffic. Pull far
enough off the road to avoid being hit when
operating the jack or changing the wheel.
7
22_WS_OM_EN_USC_t.book Page 323
Page 329 of 428
WARNING!
Carefully follow these tire changing warnings to
help prevent personal injury or damage to your
vehicle:
Always park on a firm, level surface as far from
the edge of the roadway as possible before
raising the vehicle.
Turn on the Hazard Warning Flashers.
Apply the parking brake firmly and set the
transmission in PARK.
Block the wheel diagonally opposite the wheel
to be raised.
Never start or run the engine with the vehicle
on a jack.
Do not let anyone sit in the vehicle when it is
on a jack.
Do not get under the vehicle when it is on a
jack. If you need to get under a raised vehicle,
take it to a service center where it can be
raised on a lift.
WARNING!
7
22_WS_OM_EN_USC_t.book Page 327
Page 338 of 428
![JEEP WAGONEER 2022 User Guide W $ 5N ,N *
)a Vt V S L Q Q L Qg t L Ue V Fa Q be Ga Qge Uo X V. )o U Fe V
ge Qe Uate G b \ e [ Fe V V L Ye Z Kee O V See G V Pa \
Fa X Ve Ga Page o U e Ye Q Ia L O X Ue o I t Ke a](/img/16/55990/w960_55990-337.png "JEEP WAGONEER 2022 User Guide W $ 5N ,N *
)a Vt V S L Q Q L Qg t L Ue V Fa Q be Ga Qge Uo X V. )o U Fe V
ge Qe Uate G b \ e [ Fe V V L Ye Z Kee O V See G V Pa \
Fa X Ve Ga Page o U e Ye Q Ia L O X Ue o I t Ke a")
W $ 5N ,N *
)a Vt V S L Q Q L Qg t L Ue V Fa Q be Ga Qge Uo X V. )o U Fe V
ge Qe Uate G b \ e [ Fe V V L Ye Z Kee O V See G V Pa \
Fa X Ve Ga Page o U e Ye Q Ia L O X Ue o I t Ke a [ Oe a Q G
t L Ue V. $ t L Ue Fo X O G e [ S Oo Ge a Q G L Q M X Ue Vo Peo Qe.
'o Qot V S L Q \o X U Ye K L F Oe
V Z Kee O V Ia Vte U t Ka Q
30 P S K 48 k P K \f R U I R U O R Q J H U W K D Q
Ve Fo Q G V Fo Qt L Q Xo X V O \ Z Lt Ko Xt Vto S S L Qg Z Ke Q
\o X a Ue Vt X Fk a Q G Go Qot Oet a Q \o Qe Qea U a
V S L Q Q L Qg Z Kee O Qo Patte U Z Kat t Ke V See G.
C $U 7 ,ON
Racing the engine or spinning the wheels may
lead to transmission overheating and failure.
Allow the engine to idle with the transmission
in NEUTRAL for at least one minute after every
five rocking-motion cycles. This will minimize
overheating and reduce the risk of transmis-
sion failure during prolonged efforts to free a
stuck vehicle.
When “rocking” a stuck vehicle by shifting
between DRIVE and REVERSE, do not spin the
wheels faster than 15 mph (24 km/hyf R U
drivetrain damage may result.
Revving the engine or spinning the wheels too
fast may lead to transmission overheating and
failure. It can also damage the tires. Do not
spin the wheels above 30 mph (48 km/hyf
while in gear (no transmission shifting occur -
ringyf .
Page 340 of 428
C $U 7 ,ON
Towing faster than 30 mph (48 km/hyf R U
farther than 30 miles (48 kmyf Z L W K U H D U
wheels on the ground can cause severe trans-
mission damage. Damage from improper
towing is not covered under the New Vehicle
Limited Warranty.
Page 394 of 428
W $ 5N ,N *
Do not use a tire, wheel size, load rating, or
speed rating other than that specified for your
vehicle. Some combinations of unapproved
tires and wheels may change suspension
dimensions and performance characteristics,
resulting in changes to steering, handling, and
braking of your vehicle. This can cause unpre-
dictable handling and stress to steering and
suspension components. You could lose control
and have a collision resulting in serious injury or
death. Use only the tire and wheel sizes with
load ratings approved for your vehicle.
Never use a tire with a smaller load index or
capacity, other than what was originally
equipped on your vehicle. Using a tire with a
smaller load index could result in tire over -
loading and failure. You could lose control and
have a collision.
Failure to equip your vehicle with tires having
adequate speed capability can result in
sudden tire failure and loss of vehicle control.
CAUTION!
Replacing original tires with tires of a different
size may result in false speedometer and
odometer readings.
Page 405 of 428
TEC \b \f SPECIFICATIONS
VE \b \fE IDENTIFICATION NUMBER (VIN)
The VIN is found on a label located on the left front
corner of the instrument panel pad, visible from
outside of the vehicle through the windshield.
Windshield VIN Label Location
NOTE:It is illegal to remove or alter the VIN.
BRAKE SYSTEM
Your vehicle is equipped with dual hydraulic brake
systems. If either of the two hydraulic systems lose
normal capability, the remaining system will still
function. However, there will be some loss of
overall braking effectiveness. You may notice
increased pedal travel during application, greater
pedal force required to slow or stop, and potential
activation of the Brake Warning Light.
In the event power assist is lost for any reason the
brakes will still function. However, the effort
required to brake the vehicle will be much greater
than that required with the power system
operating.
W \b \f AND TIRE TORQUE SPECIFICATIONS
Proper lug nut/bolt torque is very important to
ensure that the wheel is properly mounted to the
vehicle. Any time a wheel has been removed and
reinstalled on the vehicle, the lug nuts/bolts
should be torqued using a properly calibrated
torque wrench using a six sided (hexyf G H H S Z D O O
socket.
TORQUE SPECIFICATIONS
**Use only authorized dealer recommended lug
nuts/bolts and clean or remove any dirt or oil
before tightening.
Inspect the wheel mounting surface prior to
mounting the tire and remove any corrosion or
loose particles.
Wheel Mounting Surface
Lug Nut/Bolt
Torque **Lug Nut/
Bolt SizeLug Nut/Bolt
Socket Size
130 ft-lb
(176 N·myf M14 x 1.50 22 mm
9
22_WS_OM_EN_USC_t.book Page 403