ECO mode JEEP WRANGLER 2004 TJ / 2.G Owners Manual

To Shut Off the Passenger Airbag
1. Turn ignition to OFF position.
2. Remove the water-resistant plug.
3. Place the ignition key in the Passenger Airbag ON/
OFF Switch, press inward and turn the key to the right to
the OFF position. This will shut off the passenger airbag.
4. Reinstall the water-resistant plug.
NOTE:When the Passenger Airbag ON/OFF Switch is
in the OFF position, a indicator light will illuminate when
the ignition is ON. If the indicator light does not illumi-
nate for 3 seconds after the ignition is turned ON, or
when the Passenger Airbag ON/OFF Switch is turned
OFF (while ignition is in the ON position), have an
authorized dealer service the system immediately.
To Turn On the Passenger Airbag
1. Turn ignition to OFF position.
2. Remove the water-resistant plug.3. Place the ignition key in the Passenger Airbag ON/
OFF Switch, press inward and turn the key to the left to
the ON position. This will turn on the passenger airbag.
4. Reinstall the water-resistant plug.
NOTE:Do not turn the Passenger Airbag ON/OFF
Switch on or off with the ignition in the ON/RUN or
START positions, as the ACM could cause the ªAirbag
Warning Lampº to illuminate.
If A Deployment Occurs
The airbag system is designed to deploy when the impact
sensors detect a moderate-to-severe frontal collision, to
help restrain the driver and right front passenger, and
then to immediately deflate.
NOTE:A frontal collision that is not severe enough to
need airbag protection will not activate the system. This
does not mean something is wrong with the airbag
system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27
2

²If the shoulder belt contacts the child's face or neck,
move the child closer to the center of the vehicle.
Never allow a child to put the shoulder belt under an
arm or behind their back.
Transporting Pets
Airbags deploying in the front seat could harm your pet.
An unrestrained pet will be thrown about and possibly
injured, or injure a passenger during panic braking or in
a collision.
Pets should be restrained in the rear seat in pet harnesses
or pet carriers that are secured by seat belts.
ENGINE BREAK-IN RECOMMENDATIONS
A long break-in period is not required for the engine in
your new vehicle.
Drive moderately during the first 300 miles (500 km).
After the initial 60 miles (100 km), speeds up to 50 or 55
mph (80 or 90 km/h) are desirable.
While cruising, brief full-throttle acceleration, within the
limits of local traffic laws, contributes to a good break-in.
Wide open throttle acceleration in low gear can be
detrimental and should be avoided.
The engine oil installed in the engine at the factory is a
high quality energy conserving type lubricant. Oil
changes should be consistent with anticipated climate
conditions under which vehicle operations will occur.
The recommended viscosity and quality grades are
shown in Section 7 of this manual. NON-DETERGENT
OR STRAIGHT MINERAL OILS MUST NEVER BE
USED.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39
2

Safety Checks You Should Make Inside The
Vehicle
Seat Belts
Inspect the belt system periodically, checking for cuts,
frays and loose parts. Damaged parts must be replaced
immediately. Do not disassemble or modify the system.
Seat belt assemblies must be replaced after an accident if
they have been damaged (bent retractor, torn webbing,
etc.). If there is any question regarding belt or retractor
condition, replace the belt.
Airbag Warning Light
The light should come on and remain on for 6 to 8
seconds as a indicator check when the ignition switch is
first turned on. If the indicator is not lit during starting,
have it serviced. If the light stays on or comes on while
driving, have the system checked by an authorized
dealer.
Defrosters
Check operation by selecting the defrost mode and place
the blower control on high speed. You should feel the air
directed against the windshield.
Safety Checks You Should Make Outside The
Vehicle
Tires
Examine tires for excessive tread wear or uneven wear
patterns. Check for stones, nails, glass, or other objects
lodged in the tread. Inspect for tread cuts or sidewall
cracks. Check wheel nuts for tightness and tires (includ-
ing spare) for proper pressure.
Lights
Have someone observe the operation of all exterior lights
while you work the controls. Check turn signal and high
beam indicator lights on the instrument panel.
Fluid Leaks
Check area under vehicle after overnight parking for fuel,
coolant, oil, or other fluid leaks. Also, if gasoline fumes
are detected, the cause should be located and corrected
immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41
2

CAUTION!
To avoid damage to the mirror during cleaning,
never spray any cleaning solution directly onto the
mirror. Apply the solution onto a clean cloth and
wipe the mirror clean.
The compass/temperature display provides the outside
temperature and one of eight compass headings (N, NE,
E, SE, S, SW, W, NW).Each time the center button is pressed and released
within 3 seconds, the display toggles through the follow-
ing three configurations:
²display compass/temperature (Fahrenheit),
²display compass/temperature (Celsius),
²and display off.
Compass Calibration
Automatic Calibration
Once calibrated, the compass has the ability to self-
correct for changes in magnetic field to keep the compass
accurate. This is referred to as Automatic Calibration. If
magnetic field changes are too great, the compass will
enter CAL mode on it's own and manual calibration will
be required. To recalibrate the compass, drive the vehicle
at less than 5 mph (8 km/h) through up to 1
1¤2360É turns
in an area free from large metal objects or power lines.
When the compass has been calibrated, the CAL symbol
will turn off and the compass will function normally.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 47
3

When the vehicle is new, the compass should initially be
verified for correct compass variance (refer to Compass
Variation Adjustment) and calibrated manually (refer to
Manual Calibration). This will ensure correct initial cali-
bration and eliminate initial erroneous compass head-
ings.
Manual Calibration
If the compass appears erratic and CAL does not appear,
you must manually put the compass into the calibration
mode. To ensure proper compass calibration, make sure
the compass variance is properly set before manually
calibrating the compass (refer to Compass Variation
Adjustment).
To put the compass into calibration mode: Turn the
ignition to the ON position. Press and hold the center
button for more than 6 seconds until CAL (calibration
mode) appears in the display. To change the display
between VAR (compass variance) and CAL (compass
calibration) modes. Release the button to invoke manual
calibration mode. To recalibrate the compass, drive the
vehicle at less than 5 mph (8 km/h) through up to CAL
should display for a complete 1
1¤2360É turns in an areafree from large metal objects or power lines. When the
compass has been calibrated, the CAL symbol will turn
off and the compass will function normally.
Compass Variation Adjustment
Compass Variance is the difference between magnetic
north and geographic north. In some areas of the country,
the difference between magnetic and geographic north is
great enough to cause the compass to give false readings.
If this occurs, the compass variance must be set according
to the Compass Variance Map.
NOTE:When the mirror is in the VAR mode, the letter
ªZº will be displayed along with the currently selected
zone number.
48 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

7. High Beam Indicator Light
This light shows that the headlights are on high
beam. Pull the turn signal lever towards the
steering wheel to switch the headlights from high or
low. If the driver's door is open, and the headlights or
parklights are left on, the ªHigh Beam Indicator Lightº
will flash and a chime will sound.
8. Seat Belt Indicator Light
A warning chime and an indicator light will
alert you to buckle the seat belts. When the belt
is buckled, the chime will stop, but the light will
stay on until it times out (about 6 seconds).
9. Speedometer
Indicates vehicle speed.
10. Front Axle Lock Indicator Light Ð If Equipped
Indicates when the front axle lock has been
activated.11. Rear Axle Lock Indicator Light Ð If Equipped
Indicates when the rear axle lock has been
activated.
12. 4WD Indicator Light
This light alerts the driver that the vehicle is
in the four-wheel drive mode, and the front
and rear driveshafts are mechanically locked
together forcing the front and rear wheels to
rotate at the same speed.
13. Shift Indicator Light Ð If Equipped
This light shows the driver when to shift to the
next higher gear for best fuel economy (4.0L
Only).
14. Oil Pressure Gauge
Indicates engine oil pressure. This gauge does
not indicate oil level, and pressure varies with
engine speed, temperature and oil viscosity. Consis-
tent lower readings indicate possible malfunction.
Seek authorized service.
UNDERSTANDING YOUR INSTRUMENT PANEL 117
4

5 seconds after pressing the SET button, the station will
continue to play, but will not be locked into push-button
memory.
You may add a second FM station to each push button by
repeating the above procedure with this exception: Press
the SET button twice and SET 2 will appear in the radio
display window. Each button can be set for SET 1 and
SET 2 in the FM mode. This allows for 10 FM stations to
be locked into push button memory. The stations stored
in SET 2 memory can be selected by pressing the push
button twice.
When you are receiving the MW or LW station that you
wish to commit to push-button memory, press SET 1
button. SET 1 will appear in the radio display window.
Select the push-button you wish to lock on this station
and press and release that button.
Operating Instructions - RDS Mode
The following RDS functions can be selected while in
radio mode by pushing the appropriate button.
Time Button
Briefly press the Time button to change the display
between radio frequency and time.
To set the ªHOME CLKº use a ballpoint pen or similar
object to press the hour (H) or minute (M) buttons on the
radio, The time setting will increase each time you press
the button. Press any other button to exit from the clock
setting mode.
Any time the hour (H) or minute (M) buttons are pressed
when in the ªRDS CLKº mode the clock will automati-
cally switch to the ªHOME CLKº mode and only the
home time will be set.
Pressing and holding the TIME button for 2 seconds will
toggle the clock between ªRDS CLKº and ªHOME CLKº.
The display will indicate which clock is activated. The
ªRDS CLKº is only updated by the signal transmitted
from a radio station with an RDS signal.
124 UNDERSTANDING YOUR INSTRUMENT PANEL

TA (Traffic Announcement) Button
Pressing the TA button will enable the Traffic Information
system. If the current station does not have the TP
function or is not a RDS station the radio will beep and
display ªNO TAº and then go into the TA seek mode.
During Tape/CD mode the TA will give priority to traffic
announcements from the last tuned TA station. TA mode
is always off in the MW/LW mode.
During TA seek mode the radio display will flash ªTA
SEEKº. If no TP station is found after one cycle of the
search the radio will display ªNO TAº and then turn the
TA feature off.
PTY (Program Type) Button
²
Pressing this button once will turn on the PTY mode
for 10 seconds. If no action is taken during the 10
second time out the PTY icon will turn off. Pressing the
PTY button within 10 seconds will allow the program
format type to be selected. Toggle the PTY button to
select the following format types:
²None
²Affairs
²Children
²Classics
²Country
²Culture
²Document
²Drama
²Easy M
²Educate
²Finance
²Folk M
²Info
²Jazz
²Leisure
²Light M
²Nation M
²News
UNDERSTANDING YOUR INSTRUMENT PANEL 125
4

²Oldies
²Other M
²Phone In
²Pop M
²Religion
²Rock M
²Science
²Social
²Sport
²Travel
²Varied
²Weather
By pressing the SEEK button when the PTY icon is
displayed, the radio will be tuned to the next frequency
station with the same selected PTY name. The PTY
function only operates when in the FM mode.If a preset button is activated while in the PTY (Program
Type) mode, the PTY mode will be exited and the radio
will tune to the preset station.
AF LOC (Alternative Frequencies and Local
Frequencies) Button
Pressing the AF LOC button will toggle the radio display
as follows: LOC ON »» AF OFF »» LOC OFF. The radio
display will indicate when the LOC and AF are activated.
AF will automatically tune to another frequency of the
same national program when the signal quality of the
currently tuned frequency becomes poor.
LOC limits AF to only tune to another station within the
same region code to ensure the program remains local.
Operating Instructions - Tape Mode
Insert the cassette with the exposed tape side toward the
right and the mechanical action of the player will gently
pull the cassette into the play position.
126 UNDERSTANDING YOUR INSTRUMENT PANEL

Pinch Roller Release
If ignition power or the radio ON/OFF switch are turned
off, the pinch roller will automatically retract to protect
the tape from any damage. When power is restored to the
tape player, the pinch roller will automatically reengage
and the tape will resume play.
Dolby Noise Reduction
The Dolby Noise Reduction System* is on when-
ever the tape player is on, but may be switched
on/off.
To turn the Dolby Noise reduction System on/off: Press
the Dolby NR button (button 2) after you insert the tape.
The NR light in the display will go off when the Dolby
System is off.
* ºDolbyº noise reduction manufactured under license
from Dolby Laboratories Licensing Corporation. Dolby
and the double-D symbol are trademarks of Dolby Labo-
ratories Licensing Corporation.
Operation Instructions Ð CD Player
NOTE:
The ignition switch must be in the ON or ACC
position and the volume control ON before the CD player
will operate.
Inserting The Compact Disc
You may either insert or eject a disc with the radio OFF.
If you insert a disc with the ignition ON and the radio
OFF, the time of day will be displayed.
If the volume control is ON, the unit will switch from
radio to CD mode and begin to play when you insert the
disc. The display will show the track number and index
time in minutes and seconds. Play will begin at the start
of track 1.
Seek Button
Press the top of the SEEK button for the next selection on
the CD. Press the bottom of the button to return to the
beginning of the current selection, or return to the
beginning of the previous selection if the CD is within the
first 10 seconds of the current selection.
128 UNDERSTANDING YOUR INSTRUMENT PANEL