ABS JEEP WRANGLER 2017 JK / 3.G User Guide

WARNING!
•SABs need room to inflate. Do not lean against the
door or window. Sit upright in the center of the seat.
• Being too close to the SABs during deployment
could cause you to be severely injured or killed.
• Relying on the SABs alone could lead to more severe
injuries in a collision. The SABs work with your seat
belt to restrain you properly. In some collisions,
SABs won’t deploy at all. Always wear your seat belt
even though you have SABs.
NOTE: Air bag covers may not be obvious to you, but they
will open during air bag deployment.
Air Bag System Components
• Occupant Restraint Controller (ORC)
• Air Bag Warning Light
•Steering Wheel and Column
• Instrument Panel
• Knee Impact Bolsters
• Driver and Front Passenger Air Bags
• Supplemental Side Air Bags •
Front and Side Impact Sensors
• Seat Belt Pretensioners
• Seat Track Position Sensors
• Seat Belt Buckle Switch
If A Deployment Occurs
The front air bags are designed to deflate immediately after
deployment.
NOTE: Front and/or side air bags will not deploy in all
collisions. This does not mean something is wrong with the
air bag system.
If you do have a collision which deploys the air bags, any
or all of the following may occur:
• The air bag material may sometimes cause abrasions
and/or skin reddening to the occupants as the air bags
deploy and unfold. The abrasions are similar to friction
rope burns or those you might get sliding along a carpet
or gymnasium floor. They are not caused by contact with
chemicals. They are not permanent and normally heal
quickly. However, if you haven’t healed significantly
within a few days, or if you have any blistering, see your
doctor immediately.5
SAFETY 255

Totally Integrated Power Module
The Totally Integrated Power Module is located in the
engine compartment near the battery. This center contains
cartridge fuses, mini fuses, and relays. A label that identi-
fies each component is printed on the inside of the cover.
CavityCartridge Fuse Mini Fuse Description
J1 –– –
J2 30 Amp Pink –Transfer Case Module
J3 –– –
J4 25 Amp Clear –Driver Door Node
J5 25 Amp Clear –Passenger Door Node
J6 40 Amp Green –Anti-Lock Brake System (ABS) Pump/
Stability Control System
J7 30 Amp Pink –Anti-Lock Brake System (ABS) Valve/
Stability Control System
J8 –– –
Totally Integrated Power Module
348 IN CASE OF EMERGENCY

4. Remove the air cleaner filter element from the housingassembly.
Engine Air Cleaner Filter Installation
NOTE: Inspect and clean the housing if dirt or debris is
present before replacing the air filter element.
1. Install the air cleaner filter element into the housing assembly with the air cleaner filter inspection surface
facing downward. 2. Install the air cleaner cover onto the housing assembly
locating tabs.
3. Latch the spring clips and lock the air cleaner cover to the housing assembly and install air hose.
4. Tighten air intake clamp and tighten air cleaner intake tube bolts.
Accessory Drive Belt Inspection
WARNING!
•Do not attempt to inspect an accessory drive belt
with vehicle running.
• When working near the radiator cooling fan, discon-
nect the fan motor lead. The fan is temperature
controlled and can start at any time regardless of
ignition mode. You could be injured by the moving
fan blades.
• You can be badly injured working on or around a
motor vehicle. Only do service work for which you
have the knowledge and the proper equipment. If
you have any doubt about your ability to perform a
service job, take your vehicle to a competent me-
chanic.
Air Cleaner Filter
1 — Air Cleaner Filter
2 — Air Cleaner Filter Inspection Surface 384 SERVICING AND MAINTENANCE

4. Disengage the two retaining tabs that secure the two airfilter access doors to the HVAC housing.
5. Open the two air filter access doors.
6. Remove the two particulate air filters from the HVAC air inlet housing. Pull the filter elements straight out of
the housing, one at a time. 7. Install the A/C air filter with the air filter position
indicators pointing in the same direction as removal.
CAUTION!
The cabin air filter is identified with an arrow to
indicate airflow direction through the filter. Failure to
properly install the filter will result in the need to
replace it more often.
Air Filter Retaining Tabs
1 — Left Retaining Tab
2 — Right Retaining Tab
Air Filter Access Door Open
1 — Air Conditioning Filter Access Door
2 — Air Conditioning Air Filter
388 SERVICING AND MAINTENANCE

8. Close A/C Air Filter access doors and secure retainingtabs.
9. Rotate the glove compartment door back into position.
Refer to the “Maintenance Plan” for the proper mainte-
nance intervals.
Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, door hinge pivot points and rollers, liftgate,
tailgate, decklid, sliding doors and hood hinges, should be
lubricated periodically with a lithium based grease, such as
MOPAR Spray White Lube to assure quiet, easy operation
and to protect against rust and wear. Prior to the applica-
tion of any lubricant, the parts concerned should be wiped
clean to remove dust and grit; after lubricating excess oil
and grease should be removed. Particular attention should
also be given to hood latching components to ensure
proper function. When performing other underhood ser-
vices, the hood latch, release mechanism and safety catch
should be cleaned and lubricated.
The external lock cylinders should be lubricated twice a
year, preferably in the Fall and Spring. Apply a small
amount of a high quality lubricant, such as MOPAR Lock
Cylinder Lubricant directly into the lock cylinder.
Windshield Wiper Blades
Clean the rubber edges of the wiper blades and the
windshield periodically with a sponge or soft cloth and a
mild nonabrasive cleaner. This will remove accumulations
of salt or road film.
Operation of the wipers on dry glass for long periods may
cause deterioration of the wiper blades. Always use washer
fluid when using the wipers to remove salt or dirt from a
dry windshield.
Avoid using the wiper blades to remove frost or ice from
the windshield. Keep the blade rubber out of contact with
petroleum products such as engine oil, gasoline, etc.
NOTE: Life expectancy of wiper blades varies depending
on geographical area and frequency of use. Poor perfor-
mance of blades may be present with chattering, marks,
water lines or wet spots. If any of these conditions are
present, clean the wiper blades or replace as necessary.
8
SERVICING AND MAINTENANCE 389

WARNING!(Continued)
•To avoid contamination from foreign matter or mois-
ture, use only new brake fluid or fluid that has been
in a tightly closed container. Keep the master cylin-
der reservoir cap secured at all times. Brake fluid in
a open container absorbs moisture from the air
resulting in a lower boiling point. This may cause it
to boil unexpectedly during hard or prolonged brak-
ing, resulting in sudden brake failure. This could
result in a collision.
• Overfilling the brake fluid reservoir can result in
spilling brake fluid on hot engine parts, causing the
brake fluid to catch fire. Brake fluid can also damage
painted and vinyl surfaces, care should be taken to
avoid its contact with these surfaces.
• Do not allow petroleum based fluid to contaminate
the brake fluid. Brake seal components could be
damaged, causing partial or complete brake failure.
This could result in a collision.
Front/Rear Axle Fluid
For normal service, periodic fluid level checks are not
required. When the vehicle is serviced for other reasons the
exterior surfaces of the axle assembly should be inspected.
If gear oil leakage is suspected inspect the fluid level. Refer
to “Fluids And Lubricants” in “Technical Specifications”
for further information.
Fluid Level Check
Lubricant should be at the bottom edge of the oil fill hole.
Adding Fluid
Add lubricant only at the fill hole and only to the level
specified above.
Selection Of Lubricant
Use only the manufacturer’s recommended fluid. Refer to
“Fluids And Lubricants” in “Technical Specifications” for
further information.
8
SERVICING AND MAINTENANCE 401

Tire MarkingsNOTE:
•P (Passenger) — Metric tire sizing is based on U.S.
design standards. P-Metric tires have the letter “P”
molded into the sidewall preceding the size designation.
Example: P215/65R15 95H.
• European — Metric tire sizing is based on European
design standards. Tires designed to this standard have
the tire size molded into the sidewall beginning with the
section width. The letter Pis absent from this tire size
designation. Example: 215/65R15 96H.
• LT (Light Truck) — Metric tire sizing is based on U.S.
design standards. The size designation for LT-Metric
tires is the same as for P-Metric tires except for the letters
“LT” that are molded into the sidewall preceding the
size designation. Example: LT235/85R16.
• Temporary spare tires are designed for temporary emer-
gency use only. Temporary high pressure compact spare
tires have the letter “T” or “S” molded into the sidewall
preceding the size designation. Example: T145/80D18
103M.
• High flotation tire sizing is based on U.S. design stan-
dards and it begins with the tire diameter molded into
the sidewall. Example: 31x10.5 R15 LT.
Tire Markings
1 — U.S. DOT Safety Standards
Code (TIN) 4 — Maximum Load
2 — Size Designation 5 — Maximum Pressure
3 — Service Description 6 — Treadwear, Traction and
Temperature Grades
406 SERVICING AND MAINTENANCE

The manufacturer will not stand behind any service contract
that is not the manufacturer’s service contract. It is not
responsible for any service contract other than the manufac-
turer’s service contract. If you purchased a service contract
that is not a manufacturer’s service contract, and you require
service after the manufacturer’s New Vehicle Limited War-
ranty expires, please refer to the contract documents, and
contact the person listed in those documents.
We appreciate that you have made a major investment
when you purchased the vehicle. An authorized dealer has
also made a major investment in facilities, tools, and
training to assure that you are absolutely delighted with
the ownership experience. You will be pleased with their
sincere efforts to resolve any warranty issues or related
concerns.
WARNING!
Engine exhaust (internal combustion engines only),
some of its constituents, and certain vehicle compo-
nents contain, or emit, chemicals known to the State of
California to cause cancer and birth defects, or other
reproductive harm. In addition, certain fluids con-
tained in vehicles and certain products of component
wear contain, or emit, chemicals known to the State of
California to cause cancer and birth defects, or other
reproductive harm.
WARRANTY INFORMATION
See the Warranty Information Booklet, located in the owner ’s
information kit, for the terms and provisions of FCA US LLC
warranties applicable to this vehicle and market.
MOPAR PARTS
MOPAR fluids, lubricants, parts, and accessories are avail-
able from an authorized dealer. They are recommended for
your vehicle in order to help keep the vehicle operating at
its best.
11
CUSTOMER ASSISTANCE 505

About Your Brakes........................ .436
Adding Engine Coolant (Antifreeze) .............397
Adding Fuel ............................. .312
Additives, Fuel ........................... .438
AirBag ................................ .250
Advance Front Air Bag ....................250
Air Bag Operation ....................... .252
Enhanced Accident Response .............256, 368
Event Data Recorder (EDR) .................368
FrontAirBag .......................... .250
If A Deployment Occurs ....................255
Knee Impact Bolsters ..................... .252
Maintaining Your Air Bag System .............257
Transporting Pets ....................... .278
Air Bag Light ......................... .196, 280
Air Bag Maintenance ....................... .257
Air Cleaner, Engine (Engine Air Cleaner Filter) ......381
Air Conditioner Maintenance ..................385
Air Conditioning Filter ....................69, 387
Air Conditioning, Operating Tips ................68
Air Conditioning Refrigerant ...............385, 386
Air Conditioning System .....................385
Air Filter ............................... .381
Air Pressure, Tires ......................... .414
Alarm (Security Alarm) ....................26, 201 Alterations/Modifications, Vehicle
................7
Antenna, Satellite Radio ..................... .465
Antifreeze (Engine Coolant) ................396, 442
Disposal .............................. .398
Anti-Lock Brake System (ABS) .................214
Anti-Lock Warning Light .....................202
Arming System (Security Alarm) ................27
Assistance Towing ......................... .483
Assist, Hill Start .......................... .216
Automatic Dimming Mirror ....................50
Automatic Headlights ........................53
Automatic Oil Change Indicator ................195
Automatic
Transmission ..................295, 405
Adding Fluid .......................... .405
Fluid And Filter Changes ...................405
Fluid Change .......................... .405
Fluid Level Check .....................402, 403
Fluid Type ......................... .402, 445
Special Additives ........................ .403
Autostick ............................... .300
Auxiliary Electrical Outlet (Power Outlet) .........176
Auxiliary Power Outlet ..................... .176
Axle Fluid .............................. .445
Axle Lock ............................... .305
510 INDEX

Battery.............................. .199, 378
Charging System Light ....................199
Keyless Key Fob Replacement ................20
Belts, Seat ............................... .280
Body Mechanism Lubrication ..................389
B-Pillar Location .......................... .409
Brake Assist System ........................ .216
Brake Control System, Electronic ................215
Brake Fluid .......................... .400, 445
Brake System ......................... .400, 436
Anti-Lock (ABS) ........................ .436
Fluid Check ........................... .400
Master Cylinder ........................ .400
Parking .............................. .288
Warning Light .......................... .197
Brake/Transmission Interlock ..................295
Bulb Replacement ...................... .342, 343
Bulbs, Light .......................... .282, 342
Calibration, Compass ....................... .188
Capacities, Fluid .......................... .442
Caps, Filler Fuel ................................. .312
Oil (Engine) ........................... .377
Power Steering ......................... .308Radiator (Coolant Pressure)
.................398
Carbon Monoxide Warning ................279, 441
Cargo Light ...............................56
Car Washes .............................. .428
Cellular Phone ........................ .471, 472
Center High Mounted Stop Light ...............346
Certification Label ......................... .313
Chains, Tire ............................. .423
Changing A Flat Tire .....................353, 405
Check Engine Light (Malfunction Indicator Light) . . . .211
Checking Your Vehicle For Safety ...............279
Checks, Safety ............................ .279
Child

Restraint ........................... .259
Child Restraints Booster Seats ........................... .262
Child Restraints ........................ .259
Child Seat Installation .....................275
How To Stow An Unused ALR Seat Belt ........272
Infants And Child Restraints ................261
LATCH Positions ........................ .266
Locating The LATCH Anchorages .............269
Lower Anchors And Tethers For Children .......265
Older Children And Child Restraints ...........261
Seating Positions ........................ .264
Child Safety Locks ..........................31
12
INDEX 511