ECU JEEP WRANGLER 2017 JK / 3.G User Guide

To Raise The Rear Seat
Raise the seatback and lock it into place. If interference
from the cargo area prevents the seatback from fully
locking, you will have difficulty returning the seat to its
proper position.
NOTE:If the rear seatback is not fully latched, the center
shoulder belt will not be able to be extended for use. If you
cannot extend the center shoulder belt, make sure your
seatback is fully latched.
WARNING!
Be certain that the seatback is securely locked into
position. If the seatback is not securely locked into
position the seat will not provide the proper stability
for child seats and/or passengers. An improperly
latched seat could cause serious injury.
Heated Seats — If Equipped
On some models, the front driver and passenger seats may
be equipped with heaters in both the seat cushions and
seatbacks. There are two heated seat switches that allow the driver
and passenger to operate the seats independently. The
controls for each seat are located on a switch bank near the
bottom center of the instrument panel.
You can choose from HI, LO or OFF heat settings. Amber
indicator lights in each switch indicate the level of heat in
use. Two indicator lights will illuminate for HI, one for LO
and none for OFF.
Push the switch once to select HI-level heating.
Push the switch a second time to select LO-level
heating. Push the switch a third time to shut the
heating elements OFF.
When the HI-level setting is selected, the heater will
provide a boosted heat level during the initial stages of
operation. Then, the heat output will drop to the normal
HI-level. If the HI-level setting is selected, the system will
automatically switch to LO-level after approximately 30
minutes of continuous operation. At that time, the number
of illuminated LEDs changes from two to one, indicating
the change. The LO-level setting will turn OFF automati-
cally after approximately 30 minutes.
3
GETTING TO KNOW YOUR VEHICLE 45

WARNING!
•A loose head restraint thrown forward in a collision
or hard stop could cause serious injury or death to
occupants of the vehicle. Always securely stow re-
moved head restraints in a location outside the
occupant compartment.
(Continued)
WARNING! (Continued)
•ALL the head restraints MUST be reinstalled in the
vehicle to properly protect the occupants. Follow the
re-installation instructions above prior to operating
the vehicle or occupying a seat.
NOTE: Do not reposition the head restraint 180 degrees to
the incorrect position in an attempt to gain additional
clearance to the back of the head.
Rear Head Restraints — 2 Door Model
The rear seat head restraints are not adjustable. They can be
removed to make it easier to take out the rear seat. To
remove the head restraint, push the button on each of the
two head restraint guides and pull upward on the head
restraint. Replace the head restraint before driving the
vehicle with passengers in the rear seat. To replace the head
restraint, insert the head restraint rods into the guides and
push downward on the head restraint until locked. Refer to
“Occupant Restraint Systems” in “Safety” for information
on child seat tether routing.
1 — Release Button
2 — Adjustment Button
3
GETTING TO KNOW YOUR VEHICLE 47

WARNING!
•Do not drive the vehicle without the rear seat head
restraints installed while passengers are occupying
the rear seat. In a collision, people riding in this area
without the head restraints installed are more likely
to be seriously injured or killed.
• A loose head restraint thrown forward in a collision
or hard stop could cause serious injury or death to
occupants of the vehicle. Always securely stow re-
moved head restraints in a location outside the
occupant compartment.
• ALL the head restraints MUST be reinstalled in the
vehicle to properly protect the occupants. Follow the
reinstallation instructions above prior to operating
the vehicle or occupying a seat. NOTE:
Do not reposition the head restraint 180 degrees to
the incorrect position in an attempt to gain additional
clearance to the back of the head.
Rear Head Restraints — 4 Door Model
The rear seat is equipped with nonadjustable head re-
straints. Refer to “Occupant Restraint Systems” in “Safety”
for information on child seat tether routing.
STEERING WHEEL
Tilt Steering Column
This feature allows you to tilt the steering column upward
or downward. The tilt lever is located on the steering
column, below the turn signal lever.
To Adjust The Tilt Steering Column
1. Push down on the lever to unlock the steering column.
2. With one hand firmly on the steering wheel, move the steering column up or down, as desired.
3. Pull upwards on the lever to lock the column firmly in place.
48 GETTING TO KNOW YOUR VEHICLE

Four-Door Models
The lower left switch controls the left rear passenger
window, and the lower right switch controls the right rear
passenger window.
Wind Buffeting
Wind buffeting can be described as the perception of
pressure on the ears or a helicopter-type sound in the ears.
Your vehicle may exhibit wind buffeting with the windows
down in certain open or partially open positions. This is a
normal occurrence and can be minimized by adjusting the
window opening.
DUAL TOP — TWO-DOOR MODELS —
IF EQUIPPED
Please visit
http://www.jeep.com/en/wrangler-rooftop-instructions/
for instructional videos.
If your vehicle is equipped with a Dual Top,you must
remove one of the tops from the vehicle. If the soft top is
removed, the pivot brackets must also be removed from
the sport bar. The soft top was installed at the factory for
shipping purposes only. The soft top and the hard top are
to be used independently. Removal is mandatory to prevent any possible wear and tear on the soft top. Your
vehicle warranty will not cover damage resulting from
both tops remaining on the vehicle at the same time for
extended periods of time.
Removing The Soft Top — Two-Door Models
1. Locate and remove the two boxes that contain the
following items:
• Right and left door frames
• Four door frame attachment knobs
• Right and left quarter windows
• Rear window
• Two rear window roll up straps
• Two Sunrider secure straps (if equipped)
• Two rear swing gate brackets
2. Remove the hard top. Refer to “Freedom Top Three- Piece Modular Hard Top — Front/Rear Panel Removal”
in this section.
72 GETTING TO KNOW YOUR VEHICLE

4. If the soft top has been removed, follow these steps toreinstall the soft top. If the soft top is on the vehicle,
proceed to step #5.
a. If the pivot brackets have been removed, unzip the sport bar covers and attach the pivot brackets to the
sports bar with the four screws that were removed
using a #T30 Torx head driver. Re-cover and re-zip
the sport bar covers.
b. Lay the soft top into the rear of the vehicle with the bows pointing forward and the curved portion of the
bows facing upward.
c. Reattach the knuckles onto the metal pivot brackets.
NOTE: To aid in reattaching the knuckles, you may care-
fully tap on the knuckles using a rubber mallet.
d. Screw the pivot screws back into place using a #T30 Torx head driver. Secure them until they are snug,
being careful not to cross-thread the screws or over-
tighten.
Step Four
3
GETTING TO KNOW YOUR VEHICLE 75

Removing The Soft Top — Four-Door Models
1. Locate and remove the two boxes that contain thefollowing items:
• Right and left door frames
• Six door frame attachment knobs
• Right and left quarter windows
• Rear window
• Two rear window roll up straps
• Two Sunrider secure straps (if equipped)
• Two rear swing gate brackets
2. Remove the hard top. Refer to “Freedom Top Three- Piece Modular Hard Top — Front/Rear Panel Removal”
in this section. 3. Ensure the tether strap is secure to the pivot bracket.
Unbutton the side bow tether strap (both sides).
Step Three
3
GETTING TO KNOW YOUR VEHICLE 77

5. Lower the pivot bracket onto the sport bar bracketmounting tab in a downward motion to lock into tab.
6. Install the pivot bracket bolts back into place using a 10.0 mm wrench or socket driver. Secure them until they
are snug, being careful not to cross-thread the screws or
overtighten.
CAUTION!
Do not overtighten the screws. You can strip the screws
if they are overtightened. 7. Remove the tether strap from the pivot bracket.
Step Five
Step Seven
3
GETTING TO KNOW YOUR VEHICLE 81

2. Unfold the black panel divider (ensure the divider islaying flat). Secure the Velcro, located at the center of the
divider. 3. Insert the left-side Freedom panel into the bag with the
latches facing upward.
NOTE: Ensure the front Freedom panel latch is closed
prior to inserting the panel into the bag.
Step Two
Step Three
3
GETTING TO KNOW YOUR VEHICLE 87

6. Lift the Freedom bag into the vehicle with the hooks andstraps facing the back of the rear seat. Attach the clips at
the bottom of the bag to the child restraint anchorages,
located at the base of the rear seat. 7. Wrap the upper strap around the rear head restraints
and loop the strap through the buckle. Pull on the strap
to tighten the Freedom bag securely against the rear
seat.
Step SixStep Seven
3
GETTING TO KNOW YOUR VEHICLE 89

Rear Hard Top Removal
1. Remove both front panels. Refer to “Front Panel(s)Removal” in this section.
2. Open both doors.
3. Remove the two Torx head screws that secure the hard top at the B-pillar (near the top of the door) using a #40
Torx head driver (Four–Door Only).
4. Remove the six Torx head screws that secure the hard top to the vehicle (along the interior bodyside) using a
#40 Torx head driver.
5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass.
Step Five
3
GETTING TO KNOW YOUR VEHICLE 91