ECU KIA CARNIVAL 2007 Owner's Manual

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Loosen the wheel nuts slightly.
Raise the front of the vehicle, and make sure it is securely supported.
2. Remove the front wheel and tire (A) from front hub (B).
Be careful not to damage to the hub bolts (C) when removing the front wheel and tire (A).
3. Remove the brake hose bracket bolt (A, B) from the front strtu assembly.
4.Remove the speed sensor (A) and wire (B) bolts from the front knuckle.
5.Remove the front stabilizer link (A) nut (B) from the strut assembly.

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Loosen the wheel nuts slightly.
Raise the front of the vehicle, and make sure it is securely supported.
2. Remove the front wheel and tire (A) from front hub (B).
Be careful not to damage the hub bolts(C) when removing the front wheel and tire(A).
3. Remove the front lower arm (A) mounting bolt (B) from the knuckle.
4.Remove the lower arm mounting bolts (A, B).
REPLACEMENT
1.Using the special tools(09214- 32000 & 09216 - 211000), remove the bushing from the lower arm.

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Remove the connecting bolt (A) between the steering universal joint assembly (B) and the pinion assembly.
2.Loosen the wheel nuts slightly. Raise the front of the vehicle, and make sure it is securely supported.
3. Remove the front wheel and tire (A) from front hub (B).
Be careful not to damage the hub bolts (C) when removing the front wheel and tire (A).
4. Remove the front stabilizer link (A) nut (B) from the strut assembly.
5.After removing both sides of the tie rod end (A) self - locking nuts (B) and cotterpin (C), remove the ball joint by
using the special tool(09568- 4A000).

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Loosen the wheel nuts slightly.
Raise the rear of the vehicle, and make sure it is securely supported.
2. Remove the rear wheel and tire (A) from rear hub (B).
Be careful not to damage the hub bolts (C) when removing the rear wheel and tire (A).
3. Remove the rear shock absorber assembly mounting bolts (A) and nut (B) from the baby.
4.Remove the rear shock absorber assembly nut (B) from the rear knuckle, then remove the shock absorber
assembly (A).
5.Remove the rear shock absorber bracket bolt (A).

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Loosen the wheel nuts slightly. Raise the rear of the vehicle, and make sure it is securely supported.
2. Remove the rear wheel and tire (A) from rear hub (B).
Be careful not to damage the hub bolts (C) when removing the rear wheel and tire (A).
3. Remove the brake caliper mounting bolts (A), and then place the brake caliper assembly (B) with wire as shown in
the illustration.
4.Remove the rear upper arm ball joint self - locking nut (A) and the cotter pin.

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Loosen the wheel nuts slightly.
Raise the rear of the vehicle, and make sure it is securely supported.
2. Remove the rear wheel and tire (A) from rear hub (B).
Be careful not to damage the hub bolts (C) when removing the rear wheel and tire (A).
3. Remove the lower arm bolt (B) from the rear knuckle, while supporting the lower arm (A) with a jack as shown in
the illustration. Loosen the lower arm bolt (C) from the cross member.
4.Remove the spring (A), the lower seat, and the upper pad.
5.Remove the lower arm (A) mounting bolts (B) from the cross member (C).

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Loosen the wheel nuts slightly. Raise the rear of the vehicle, and make sure it is securely supported.
2. Remove the rear wheel and tire (A) from rear hub (B).
Be careful not to damage the hub bolts (C) when removing the rear wheel and tire (A).
3. Remove the brake caliper mounting bolts (A), and then place the brake caliper assembly (B) with wire as shown in
the illustration.
4.Remove the rear assist arm (A) ball joint self - locking nut (B) and the cotter pin.

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Loosen the wheel nuts slightly. Raise the rear of the vehicle, and make sure it is securely supported.
2. Remove the rear wheel and tire (A) from rear hub (B).
Be careful not to damage the hub bolts (C) when removing the rear wheel and tire (A).
3. Remove the wheel speed sensor wire's bracket bolt (A) from the body and the connector.
4.Remove the wheel speed sensor wire's bracket bolt (A) and the parking brake wire's bracket bolt (B).
5.Remove the trailing arm (A) mounting nuts (B) from the knuckle.

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Loosen the wheel nuts slightly.
Raise the rear of the vehicle, and make sure it is securely supported.
2. Remove the rear wheel and tire (A) from rear hub (B).
Be careful not to damage the hub bolts (C) when removing the rear wheel and tire (A).
3. Remove the left/right nuts (C) of the rear stabilizer links (B) from the trailing arm (A).
4.Remove the left/right mounting nuts (B) of the rear stabilizer bar brackets (A).
5.Remove the rear stabilizer link (A) nut (B) from the stabilizer bar assembly.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Check the condenser fins for clogging and damage. If clogged, clean them with water, and blow them with
compressed air. If bent, gently bend them using a screwdriver or pliers.
2. Check the condenser connections for leakage, and repair or replace it, if required.
REPLACEMENT
CONDENSER ASSEMBLY
1. Recover the refrigerant with a recovery/ recycling/ charging station (Refer to HA - 8).
2. Disconnect the negative ( - ) battery terminal.
3. Remove the radiator. (Refer to EM group)
4. Remove 2 bolts, and then remove the condenser (A) by lifting it up. Be careful not to damage the radiator and
condenser fins when removing the condenser.
5.Install in the reverse order of removal, and note these items :
a. If you're installing a new condenser, add refrigerant oil ND- OIL8.
b. Replace the O - rings with new ones at each fitting, and apply a thin coat of refrigerant oil before installing them.
Be sure to use the right O - rings for R- 134a to avoid leakage.
c. Be careful not to damage the radiator and condenser fins when installing the condenser.
d. Be sure to install the lower mount cushions of condenser securely into the holes.
e. Charge the system, and test its performance. (Refer to HA - 9)
DESICCANT
1.Remove the condenser, and then remove the bottom cap (B) with L wrench (A) from the condenser.
TORQUE: 20~25N.m (2.0~2.5kgf•m, 14.5~18.2lb - ft)