check engine KIA Magnetis 2006 2.G User Guide
[x] Cancel search | Manufacturer: KIA, Model Year: 2006, Model line: Magnetis, Model: KIA Magnetis 2006 2.GPages: 225, PDF Size: 3.77 MB
Page 101 of 225

3. If leaks are found, if the warning
light remains ON, or if the brakes do
not operate properly, do not drive the
vehicle. Have it towed to an
Authorized Kia Dealer for a brake
system inspection and necessary
repairs.
To check bulb operation, the warning
light illuminates when the ignition switch
is in the ON position.
IMMOBILIZER
INDICATOR
(IF EQUIPPED)This light illuminates when the
immobilizer key is inserted and turned to
the ON position to start the engine.
If this light turns off or blinks when the
ignition switch is in the ON position
before starting the engine, have the
system checked by an authorized Kia
Dealer. AIR BAG WARNING This warning light will remain ON for
approximately 6 seconds each time you
turn the ignition switch ON. If the
system does not operate as described or
if the light comes on while the vehicle is
being driven, see an Authorized Kia
Dealer for immediate assistance.
SAFETY BELT WARNINGAs a reminder to the driver and
passenger, safety belt warning light will
blink for approximately 6 seconds each
time you turn the ignition switch ON.
If the driver's lap/shoulder belt is not
fastened when the key is turned ON or if
it is unfastened after the key is turned
ON, the safety belt warning light blinks
for approximately 6 seconds. SAFETY BELT WARNING
CHIME If the driver's seat belt is not fastened
when the ignition key is turned “ON” or
if it is disconnected after the key is ON,
the safety belt warning chime will sound
for approximately 6 seconds.
DRIVING YOUR VEHICLE
4-22
WARNING -
Brake
Warning Lights
Driving the vehicle with a
warning light ON is dangerous.
If the brake warning light
remains ON, have the brakes
checked and repaired
immediately.
AIR
BAG
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 22
Page 102 of 225

CHARGING SYSTEM
WARNING
(IF EQUIPPED)This warning light indicates a
malfunction of either the generator or
electrical charging system.
If the warning light illuminates while
driving:
1. Drive to the nearest safe location and
carefully stop your vehicle.
2. With the engine OFF, check the
generator drive belt for looseness or
breakage.
3. If the belt is adjusted properly, a
problem exists somewhere in the
electrical charging system. Have an
Authorized Kia Dealer or other
competent locate and correct the
problem as soon as possible.
ENGINE OIL PRESSURE
WARNING This warning light indicates the engine
oil pressure is low.
If the warning light illuminates while
driving:
1. Drive safely to the side of the road
and stop.
2. With the engine OFF, check the
engine oil level. If the level is low,
add oil as required.
If the warning light remains ON after
adding oil or if oil is not available, call
an Authorized Kia Dealer.
LOW FUEL LEVEL
WARNING This warning light indicates the fuel tank
is near empty. The warning light will
come on when the fuel level has dropped
to about 8.5 L (2.2 US gal.).
Refuel as soon as possible.
4-23
✻
NOTICE
Do not drive the vehicle with a
loose or broken generator belt; the
engine could be damaged by over-
heating because this belt also drives
the water pump.
✻
NOTICE
Do not drive the vehicle when the
Engine Oil Warning Light is ON.
If the engine is not stopped as soon
as possible, severe engine damage
could result.
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 23
Page 103 of 225

MALFUNCTION
INDICATOR LIGHT
(IF EQUIPPED)The CHECK ENGINE or malfunction
indicator light is installed in your
vehicle’s instrument panel and responds
to signals from the vehicle’s On Board
Diagnostic (OBD -II) System. The OBD-
II System monitors the performance of the
vehicle’s Emission Control System
(ECS), which is designed to reduce the
amount of air pollutants in engine exhaust
to the levels required by government
regulations.
When you first start the engine, the check
engine light will illuminate briefly as a
system check to confirm that the OBD-II
System is operating properly. As the
engine starts, this light turns off.
However, if at any time the OBD-II
system detects a faulty signal or
determines that the ECS is not performing
to specification, the CHECK ENGINE
light will illuminate continuously or flash.
Continuously ON :If the CHECK ENGINE light comes ON
while driving and illuminates continuously,
a potential problem has been discovered in
the ECS or one of the exhaust system
components. Generally, the vehicle will
continue to be driveablebut it should
be checked by an Authorized Kia Dealer
as soon as possible. This condition is
unlikely to lead to engine damage unless
a decrease in vehicle power or poor
running conditions is immediately
apparent.
Flashing ON and OFF :If the CHECK ENGINE light begins to
flash ON and OFF, a more serious
problem with the ECS or exhaust system
component has been detected. If this
happens, and there is no degradation
to performance, the vehicle is still
driveable(avoid high speeds) but should
be checked by an Authorized Kia Dealer
at your earliest possible convenience. If
the flashing CHECK ENGINE light is
accompanied by a decrease in power or
poor running conditions, safely stop the
vehicle and immediately contact Kia
Roadside Assistance.
Note that the CHECK ENGINE light
will illuminate for a problem like a loose
or missing gas cap, but will not
illuminate as a result of low engine oil or
coolant, low automatic transaxle fluid or
engine overheating. The driver will be
alerted to these conditions by other
indicators on the instrument panel.
DRIVING YOUR VEHICLE
4-24
CHECK
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 24
Page 104 of 225

4-25
KEY REMINDER WARNING
CHIMEIf the driver’s door is opened and the
ignition key is left in the ignition switch,
the key reminder warning chime will
sound. This is to remind you to remove
your keys from the ignition before you
lock the vehicle.
HEADLIGHT HIGH
BEAM INDICATORThis indicator illuminates when the
headlights are on and in the high beam
position or when the turn signal lever is
pulled into the Flash-to-Pass position.DOOR AJAR WARNINGThis warning light comes on when a
door is not closed securely with the
ignition switch in any position.
CAUTION
Prolonged driving with the On
Board Diagnostic System
Malfunction Indicator Light ( )
illuminated may cause damage to
the emission control systems
which could effect driveability
and/or fuel economy.
If the On Board Diagnostic
System Malfunction Indicator
Light ( ) begins to flash ON
and OFF, potential catalytic con-
verter damage is possible which
could result in loss of engine
power. Have the On Board
Diagnostic System inspected as
soon as possible by an
Authorized Kia Dealer or other
competent repair shop.
CHECK
CHECK
✻
NOTICE
A loose fuel filler cap may cause the
On Board Diagnostic System
Malfunction Indicator Light ( ) in
the instrument panel to illuminate
unnecessarily. Always ensure that
the fuel filler cap is tight.
CHECK
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 25
Page 105 of 225

ANTI-LOCK BRAKE SYSTEM
(ABS) WARNING LIGHT
(IF EQUIPPED)This light illuminates when you start the
engine. The light will go off if the ABS
is operating normally. Also, this light
comes on if the key is turned to ON, and
then goes off in 2-3 seconds if the system
is operating normally. If this warning
light illuminates while the vehicle is
being driven, have the vehicle checked
by an Authorized Kia Dealer or other
competent repair shop as soon as
possible.
FRONT FOG INDICATOR
(IF EQUIPPED)This light comes on when the fog lights
are ON.CRUISE INDICATOR
(IF EQUIPPED)The cruise indicator light in the
instrument cluster is illuminated only
when the vehicle cruising speed has been
set using the control switch. The
indicator light does not illuminate when
the main cruise control switch is
activated.TRUNK LID OPEN
WARNING LIGHT This light remains on unless the trunk lid
is completely closed.
TRACTION CONTROL
INDICATOR LIGHTS
(IF EQUIPPED)The TCS indicator will illuminate when
the ignition key is turned to the “ON”
position, but should go off after 3
seconds. It means the TCS is in the
stand-by status and at the moment of the
actual operation of the TCS, the indicator
will blink.
Press the TCS switch, then the system
will be deactivated and the TCS
indicator will illuminate.
If the TCS indicator stays on in the TCS
ON mode, take your car to your
Authorized Kia Dealer and have the
system checked.
DRIVING YOUR VEHICLE
4-26
ABS
CRUISE
TCS
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 26
Page 110 of 225

ONE-TOUCH WIPERSFor a single wiping cycle, push the
operation switch with the lever in the
OFF position.
WINDSHIELD WASHERTo use the windshield washer, pull the
lever toward the steering wheel.
If the washer does not work, check the
washer fluid level. If the fluid level is not
sufficient, add an appropriate, non-
abrasive, windshield washer fluid to the
washer reservoir. The reservoir filler
neck is located in the front of the engine
compartment, on the passenger’s side.
4-31
INT
TIME
PULL
MMSA4032switch
INT
TIME
PULL
MMSA4033
✻
NOTICE
• To prevent possible damage to the
wipers or windshield, do not oper-
ate the wipers when the windshield
is dry.
• To prevent damage to the wiper
blades, do not use gasoline,
kerosene, paint thinner, or other
solvents on or near them.
• To prevent damage to the wiper
arms and other compo-nents, do
not attempt to move the wipers
manually.
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 31
Page 120 of 225

4-41
TCS ON/OFF MODEIn the TCS ON mode, the indicator in the
instrument cluster will not be illuminated.
The indicator will illuminate when the
ignition key is turned to the “ON”
position, but it should go off after 3
seconds. It means the TCS is in the stand-
by status and at the moment of the actual
operation of the TCS, the indicator will
blink.
To switch to TCS OFF mode, press the
TCS switch. System will be deactivated
and the TCS indicator in the instrument
cluster will illuminate.
If the TCS indicator stays on in the TCS
ON mode, take your car to your
Authorized Kia Dealer and have the
system checked.
✻
NOTICE
• The TCS ON mode is activated
automatically when the engine is
started.
When the TCS is operating
properly, you may feel a slight
pulsation in the vehicle. This is
only the effect of brake control
and is not unusual.
When the engine starts, your
may hear a “click” sound from
the engine compartment. This is
only the sound of the TCS being
checked.
When moving out of mud or
fresh snow with the TCS ON,
pressing the accelerator pedal
may not cause the engine speed
to increase.
MS-CNA-Eng 4(40~).QXD 7/25/2005 5:15 PM Page 41
Page 139 of 225

5-3
EMISSION CONTROL
SYSTEM The vehicle emission control system is
covered by a written limited warranty.
Please see the warranty & consumer
information manual in your vehicle.VEHICLE MODIFICATIONSThis vehicle should not be modified.
Modification of your Kia could affect its
performance, safety or durability and
may even violate governmental safety
and emissions regulations.
In addition, damage or performance
problems resulting from any modification
may not be covered under warranty.
ENGINE EXHAUST GAS
PRECAUTIONS
(CARBON MONOXIDE)Engine exhaust gases contain carbon
monoxide. Though colorless and
odorless, it is dangerous and could be
lethal, if inhaled.
Carbon monoxide can be present
with other exhaust fumes.
Therefore, if you smell exhaust
fumes of any kind inside your
vehicle, have it inspected and
repaired immediately by an
Authorized Kia Dealer. If at all
possible, do not drive with exhaust
fumes present. If you must, do so
only with all windows fully open.
Have your vehicle checked and
repaired immediately.
Do not operate the engine in confined
or closed areas (such as garages) any
more than what is necessary to move
the vehicle in or out of the area. When the vehicle is stopped in an
open area for more than a short time
with the engine running, adjust the
ventilation system to draw outside air
into the vehicle.
Turn the engine off if you smell any
exhaust fumes.
Never sit in a parked or stopped
vehicle for an extended time with the
engine running.
When the engine stalls or fails to
start, excessive attempts to re-start
the engine may cause damage to the
emission control system.
OPERATING PRECAUTIONS
FOR CATALYTIC CONVERTERSYour vehicle is equipped with a catalytic
converter emission control device.
Therefore, the following precautions
must be observed:
Use only UNLEADED FUEL.
Do not park the vehicle over or near
flammable objects, such as dry grass,
paper, leaves, etc. Under certain
conditions, they could be ignited by a
hot exhaust system.
MS-CNA-Eng 5 New.qxd 7/25/2005 5:21 PM Page 3
Page 140 of 225

DRIVING TIPS
5-4 Do not operate the vehicle when
there are signs of engine malfunction,
such as misfire or a noticeable loss of
performance.
Do not misuse or abuse the engine.
Examples of misuse are coasting
with the ignition off and descending
steep grades in gear with the ignition
off.
Do not operate the engine at high idle
speed for extended periods (5
minutes or more).
Do not modify or tamper with any
part of the engine or emission control
system. All inspections and
adjustments must be made by a
qualified technician.
Failure to observe the above precautions
could result in damage to the catalytic
converter and to your vehicle and could
void your warranties.
BEFORE DRIVINGBefore entering vehicle:
Be sure that all windows, outside
mirror(s), and outside lights are clean.
Check the condition of the tires.
Check under the vehicle for any sign
of leaks.
Be sure there are no obstacles behind
you if you intend to back up.NECESSARY
INSPECTIONSFluid levels, such as engine oil, engine
coolant, brake/clutch fluid, and washer
fluid should be checked on a regular
basis, with the exact interval depending
on the fluid. Further details are provided
in Maintenance, Section 7.
BEFORE STARTING Close and lock all doors.
Position the seat so that all controls
are easily reached.
Adjust the inside and outside
rearview mirrors.
Be sure that all lights work.
Check all gauges.
Check the operation of warning
lights when the ignition switch is
turned to the ON position.
Release the parking brake and make
sure the brake warning light goes out.
For safe operation, be sure you are
familiar with your vehicle and its
equipment.
MS-CNA-Eng 5 New.qxd 7/25/2005 5:21 PM Page 4
Page 141 of 225

5-5
DRUNK DRIVINGDrinking and driving is dangerous. Drunk
driving is the number one contributor to
the highway death toll each year. Alcohol
impairs a driver’s judgment, vision and
muscular coordination. Even a small
amount of alcohol will affect a driver’s
reflexes, perceptions and judgment.
Please don’t drink and drive, or ride with
a driver who has been drinking. Choose
a designated driver if you’re with a
group, or if you’re alone, call a cab.
DRUGS AND DRIVINGDriving while under the influence of
drugs is as dangerous or more dangerous
than driving under the influence of
alcohol, depending on the drug(s) used
and the quantity consumed. Don’t take
drugs and drive.
If you are taking a prescription medicine,
check with your doctor or pharmacist
regarding whether you may operate a
motor vehicle.
SUGGESTIONS FOR
ECONOMICAL
OPERATIONYour vehicle’s fuel economy is mainly
dependent on your style of driving, how
you drive, where you drive and when
you drive.
Each of these factors has an effect on
how many miles (kilometers) you can get
from a gallon (liter) of fuel. To operate
your vehicle as economically as possible,
use the following driving suggestions to
help save money in both fuel and repairs:
Avoid lengthy warm-up idling. Once
the engine is running smoothly, begin
driving. Remember, though, that on
cold days, engine warm-up may take
a little longer.
Save fuel by accelerating slowly after
stopping.
MS-CNA-Eng 5 New.qxd 7/25/2005 5:21 PM Page 5