service interval KIA OPTIMA 2017 Features and Functions Guide

OPTIMA FEATURES & FUNCTIONS GUIDE6*IF EQUIPPED
LCD Instrument Cluster Modes*
( Type A; Buttons located on Steering Wheel)
A
B
Trip Computer Mode: Displays driving information for
tripmeter, fuel economy, etc .
Turn-by-Turn Mode*: Displays the state of the navigation
Advanced Smart Cruise Control (ASCC) / Lane Departure
Warning System (LDWS)*: Displays the state of the ASCC
and LDWS
A/V Mode*: Displays the state of the A / V System
Service Modes: Informs on upcoming service intervals /
Warning messages related to TPMS and others / When any
door is not securely closed, this indicator will illuminate
User Settings Mode: Change settings of the doors, lamps
and other features
Press Mode button A to scroll through different LCD Instrument
Cluster Modes .
Type B cluster:
Your vehicle’s steering wheel buttons may differ from those in the illustrations.
Trip Modes / Trip Computer
The Trip Computer is a system to relay
pertinent driving information . It appears on the
display when the ignition switch or the Engine
Start /Stop button* is in the ON position .
To cycle through the Trip Modes, press the
Mode button A .
When in the Trip Computer mode , press
the Select /Reset button B to cycle through
the screens . When displaying TRIP A or TRIP
B screens, press and hold the Select /Reset
button B to reset the Tripmeter to zero ( Type
A Steering Wheel) .
REMINDERS:
•
Appearance of Tripmeter display may differ as equipped
•
All stored driving information (except Odometer and Range) is reset if the battery is disconnected
INSTRUMENT CLUSTER
FUEL ECONOMY• Range• Average MPG• Instant MPG
TRIP A• Tripmeter• Average MPG• Elapsed Time (E/T)
TRIP B• Tripmeter• Average MPG• Elapsed Time (E/T)
DIGITAL SPEEDOMETER
(Type B Cluster)

OPTIMA FEATURES & FUNCTIONS GUIDE8*IF EQUIPPED
To view a video on your mobile device, snap these QR Codes or visit the listed website .
Refer to page 2 for more information .
LCD Display: Maintenance Video
LCD Display Video
www.KuTechVideos.com/jf13/2017
www.KuTechVideos.com/jf13/2017
(Type B cluster)
Service in
Off
Service Required
0000mi.
0000mi.
QR CODESUser SettingsService Mode
To enter the User Settings mode in the
LCD Instrument Cluster Modes, press
the Mode button A when the vehicle
is at a standstill and with the ignition
switch or the ENGINE START/ STOP
button* in the ON position and select
User Settings .
You can navigate the selections on the display by pressing the
Move/Scroll button B up and down, and then selecting the item
by pressing the Select /Reset button C .
(Located on Steering Wheel)
A
B
C
Driving Assist*:
•Smart Cruise Control Response*
•Rear Cross Traffic Alert (RCTA)*
•FCW (Forward Collision Warning)*
•AEB (Autonomous Emergency
Braking)*
Door/Trunk:
•Automatic Lock & Unlock
•Smart Trunk*
•Two-Press Unlock
•Horn Feedback
Lights:
•One-Touch Turn Signal*
•Headlamp Delay
•Welcome Light*
Sound:
•Park Assist System Volume*
•Blind Spot Detection Sound*
•Welcome Sound*
Convenience:
•Seat Easy Access*
•Steering Position
•Wireless Charging
System*
•Wiper/Light Display*
Service Interval:
•Service Interval On/Off
•Set mileage/months
Other Features:
•Fuel Economy Auto Reset
•Fuel Economy Unit
•Temperature Unit
•Tire Pressure Unit*
To enter Service mode, press the Mode button A, scroll using B (Move/Scroll) to Service Mode
and press Select /Reset button C . System
will display number of miles remaining until next
service is due, as well as type of service .
When service is required,
the following will be
displayed: Service
Required .
To reset the Service mode
system, press and hold the
Select /Reset button C for
more than 1 second .
To turn Service In OFF,
go to User Settings .
Service Interval Setting
To set the service interval
when in User Settings
mode:
•Press the Move button B and scroll to
Service Interval . Press the Select /Reset
button C to enter
•Press the Move button B and toggle to ON,
then press the Select /Reset button C .
Then press the Move button B to scroll and
select the desired miles or months for your
next service
•Press the Select /Reset button C to enter
INSTRUMENT CLUSTER