brake sensor KIA OPTIMA PLUG-IN HYBRID 2017 User Guide

CAUTION
If the vehicle ahead (vehicle speed:less than 30 km/h) disappears to thenext lane, the warning chime willsound and a message will appear.Adjust your vehicle speed for vehi‐cles or objects that can suddenly ap‐pear in front of you by depressingthe brake pedal according to theroad condition ahead and drivingcondition.
In traffic situation
0+'-
In traffic, your vehicle will stop if the
vehicle ahead of you stops. Also, if the vehicle ahead of you starts moving,
your vehicle will start as well. However,
if the vehicle stops for more than 3 seconds, you must depress the acceler‐
ator pedal or move up/down the lever
(to RES+ or SET-) to start driving.
Radar to detect distance to the
vehicle ahead
0+')1
The sensor detects the distance to the
vehicle ahead.
If the sensor is covered with dirt or
other foreign matter, the vehicle to ve‐
hicle distance control may not operate
correctly.
Always keep the area in front of the sensor clean.

7-67
7
Driving your vehicle

On inclines
0+'
• During uphill or downhill driving, theadvanced smart cruise control sys‐
tem may not detect a moving vehicle in your lane, and cause your vehicle
to accelerate to the set speed. Also,
the vehicle speed will rapidly down
when the vehicle ahead is recognized
suddenly.
• Select the appropriate set speed on inclines and adjust your vehicle speed
by depressing the accelerator or
brake pedal according to the road
condition ahead and driving condition.
Lane changing
0+'
• A vehicle which moves into your lane from an adjacent lane cannot be rec‐
ognized by the sensor until it is in the sensor's detection range.
• The sensor may not detect immedi‐ ately when a vehicle cuts in suddenly.
Always pay attention to the traffic,
road and driving conditions.
• If a vehicle which moves into your lane is slower than your vehicle, yourspeed may decrease to maintain the
distance to the vehicle ahead.
• If a vehicle which moves into your lane is faster than your vehicle, your
vehicle will accelerate to the selected
speed.
0+'
• Your vehicle may accelerate when a vehicle ahead of you disappears.
• When you are warned that the vehi‐ cle ahead of you is not detected,drive with caution.

7-71
7
Driving your vehicle

Vehicle recognition
0+'
Some vehicles ahead in your lane can‐
not be recognized by the sensor as fol‐ lows:
- Narrow vehicles such as motorcycles
or bicycles
- Vehicles offset to one side
- Slow-moving vehicles or sudden-de‐
celerating vehicles
- Stopped vehicles
- Vehicles with small rear profile such
as trailers with no loads A vehicle ahead cannot be recognized
correctly by the sensor if any of follow‐
ing occurs:
- When the vehicle is pointing upwards
due to overloading in the trunk
- While making turns by steering
- When driving to one side of the lane
- When driving on narrow lanes or on
curves
Adjust your vehicle speed by depressing
the brake pedal according to the road
condition ahead and driving condition.
0+'
• When vehicles are at a standstill and the vehicle in front of you changes to
the next lane, be careful when your vehicle starts to move because it may not recognize the stopped vehi‐
cle in front of you.
0+'
• Always look out for pedestrians when your vehicle is maintaining a distance
with the vehicle ahead.
Driving your vehicle
7-72

You may not be able to identify a low
tire by simply looking at it. Always use a good quality tire pressure gauge to
measure the tire's inflation pressure.
Please note that a tire that is hot (from being driven) will have a higher pres‐
sure measurement than a tire that is
cold (from sitting stationary for at least 3 hours and driven less than
1.6 km (1 mile) during that 3 hour peri‐
od).
Allow the tire to cool before measuring the inflation pressure. Always be sure
the tire is cold before inflating to the
recommended pressure.
A cold tire means the vehicle has been sitting for 3 hours and driven for less
than 1.6 km (1 mile) in that 3 hour peri‐od.
CAUTION
We recommend that you use thesealant approved by Kia if your vehi‐cle is equipped with a Tire PressureMonitoring System. The liquid seal‐ant can damage the tire pressuresensors.
WARNING
nTPMS
•The TPMS cannot alert you to se‐vere and sudden tire damagecaused by external factors such asnails or road debris.
•If you feel any vehicle instability,immediately take your foot off theaccelerator, apply the brakes grad‐ually and with light force, andslowly move to a safe position offthe road.
WARNING
nProtecting TPMS
Tampering with, modifying, or disa‐bling the Tire Pressure MonitoringSystem (TPMS) components may in‐terfere with the system's ability towarn the driver of low tire pressureconditions and/or TPMS malfunc‐tions. Tampering with, modifying, ordisabling the Tire Pressure Monitor‐ing System (TPMS) components mayvoid the warranty for that portion ofthe vehicle.
WARNING
nFor EUROPE
•Do not modify the vehicle, it mayinterfere with the TPMS function.
•The wheels on the market do nothave a TPMS sensor.For your safety, we recommendthat you use parts for replace‐ment from an authorized Kia deal‐er.
•If you use the wheels on the mar‐ket, use a TPMS sensor approvedby a Kia dealer.If your vehicle is not equipped witha TPMS sensor or TPMS does notwork properly, you may fail theperiodic vehicle inspection conduc‐ted in your country.❈All vehicles sold in the EUROPEmarket during below periodmust be equipped with TPMS.-New model vehicle:Nov. 1, 2012 ~
-Current model vehicle:Nov. 1, 2014 ~ (Based on vehi‐cle registrations)

8-13
8
What to do in an emergency

Instrument panel (Driver’s side fuse
panel)
Fuse NameSymbolFuse rat‐ingCircuit Protected
MODULE 7
10A Around View Monitor Unit, Front Air Ventilation Seat Control Module, Front
Seat Warmer Control Module, Rear Seat Warmer Control Module
MODULE 5
10A A/C Control Module, Electro Chromic Mirror, Driver IMS Module, Head Lamp
LH/RH, Auto Head Lamp Leveling Device Module, Fuel Lid & Trunk Open Switch,
Shift Lever Indicator, Front Air Ventilation Seat Control Module, Front Seat
Warmer Control Module, Rear Seat Warmer Control Module
MODULE 6
10A BCM, Smart Key Control Module
A/CON
10A A/C Control Module, E/R Junction Block (RLY. 4 - Blower Relay), Ionizer, Active
Incar Sensor, Electronic A/C Compressor
START
10A Transaxle Range Switch, Smart Key Control Module
A/BAG
15A SRS Control Module, Passenger Occupant Detection Sensor
MODULE 3
10A BCM, Stop Lamp Switch, AFLS Unit, Keyboard, VESS Unit, A/V & Navigation Head Unit, Sport Mode Switch
MODULE 4
10A Console Switch, Blind Spot Detection Radar LH/RH, Smart Parking Assist Con‐
trol Module, Smart Cruise Control Unit, Lane Keeping Assist Module, Active Air
Flap Unit, Electric Parking Brake Module, BMS Control Module
INTERIOR LAMP
10A Trunk Room Lamp, Driver/Passenger Door Lamp, Glove Box Lamp, Driver/
Passenger Smart Key Outside Handle, Front Vanity Lamp Switch LH/RH, Over‐
head Console Lamp, Rear Personal Lamp LH/RH, Driver/Passenger Foot Lamp,Room Lamp, Center Personal Lamp
MDPS
10A MDPS Unit (Column/Rack)
Maintenance
9-58

Fuse NameSymbolFuse ratingCircuit Protected
FUSE EPB1
130A Electric Parking Brake Module
H/Lamp Washer
30A RLY. 9 (H/Lamp Washer Relay)
B+4
40A Smart Junction Block (Leak Current Autocut Device Fuse - INTERI‐
OR LAMP, MULTI MEDIA, MEMORY2, MEMORY1, Fuse - MODULE1,
DR LOCK, SMART KEY, BRAKE SWITCH)
EPB 2
230A Electric Parking Brake Module
OPCU 1
OPCU120A Electric Oil Pump Unit
DEICER
20A RLY. 10 (Deicer Relay)
AMS
10A Battery Sensor
HEATED MIRROR
10A A/C Control Module, Driver/Passenger Power Outside Mirror
WIPER 2
210A BCM, PCM
H/LAMP HI
20A Not used
HEV ECU 1
HEV
ECU110A HPCU
OPCU2
OPCU110A Electric Oil Pump Unit
ELECTRICAL WATER PUMP
ELECTRICALWATERPUMP10A Electric Water Pump (HEV)
FUEL PUMP
20A Fuel Pump Relay
Maintenance
9-66

Fuse NameSymbolFuse ratingCircuit Protected
FUSE ECU 1
20A PCM
SENSORS 2
10A Mass Air Flow Sensor, Fuel Pump Relay, Oil Control Valve #1/#2,
Canister Close Valve, Camshaft Position Sensor #1/#2, Purge Con‐
trol Solenoid Valve
TCU 2
15A Transaxle Range Switch
ACTIVE HYDRAULIC BOOSTER 3
310A Multipurpose Check Connector, Integrated Brake Actuation Unit
POWER OUTLET 3
20A Rear Power Outlet
B/UP LAMP
10A PCM, Transaxle Range Switch, Electro Chromic Mirror, Rear Com‐ bination Lamp (IN) LH/RH
PTC HEATER 1
50A PTC HEATER
PTC HEATER 2
50A PTC HEATER
IG3 1
IG3110A HYBRID WATER PUMP
IG3 2
IG3215A PCU/HPCU/POSITION SWITCH
IG3 3
IG3310A HYBRID OBC SIG
IG3 4
IG320A IG3 3 RELAY
SENSOR 1
15A Oxygen Sensor (Up/Down), E/R Junction Block (Cooling Fan Relay)

9-67
9
Maintenance

APPEARANCE CARE
Exterior care
Exterior general caution
It is very important to follow the label
directions when using any chemical cleaner or polish. Read all warning and
caution statements that appear on the
label.
Finish maintenance
Washing
To help protect your vehicle’s finish
from rust and deterioration, wash it thoroughly and frequently at least once
a month with lukewarm or cold water.
If you use your vehicle for off-road
driving, you should wash it after each off-road trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign mate‐ rials. Make sure the drain holes in the
lower edges of the doors and rocker
panels are kept clear and clean.
Insects, tar, tree sap, bird droppings, in‐ dustrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, may be used. After washing, rinse the vehicle thor‐
oughly with lukewarm or cold water. Do
not allow soap to dry on the finish.
CAUTION
•Do not use strong soap, chemicaldetergents or hot water, and donot wash the vehicle in direct sun‐light or when the body of the vehi‐cle is warm.
•Be careful when washing the sidewindows of your vehicle.Especially, with high-pressure wa‐ter, water may leak through thewindows and wet the interior.
•To prevent damage to the plasticparts and lamps, do not clean withchemical solvents or strong deter‐gents.
WARNING
nWet brakes
After washing the vehicle, test thebrakes while driving slowly to see if
(Continued)
(Continued)
they have been affected by water. Ifbraking performance is impaired, drythe brakes by applying them lightlywhile maintaining a slow forwardspeed.
High-pressure washing
• When using high-pressure washers, make sure to maintain sufficient dis‐
tance from the vehicle.
Insufficient clearance or excessive pressure can lead to component
damage or water penetration.
• Do not spray the camera, sensors or its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause the device to not operate normally.
• Do not bring the nozzle tip close to boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.

9-85
9
Maintenance