change wheel KIA OPTIMA PLUG-IN HYBRID 2017 Owners Manual

(Continued)
•When you operate the steering
wheel in a low temperature, ab‐
normal noise could occur. If the
temperature rises, the noise will
disappear. This is a normal condi‐
tion.
Tilt & telescopic steering
A tilt and telescopic steering wheel al‐
lows you to adjust the steering wheel before you drive. You can also raise it
to give your legs more room when you
exit and enter the vehicle.
The steering wheel should be posi‐ tioned so that it is comfortable for you
to drive, while permitting you to see
the instrument panel warning lights and gauges.
WARNING
•Never adjust the angle of thesteering wheel while driving. Youmay lose steering control andcause severe personal injury,death or accidents.
(Continued)
(Continued)
•After adjusting, push the steeringwheel both up and down to be cer‐tain it is locked in position.
0+'
To change the steering wheel angle,
pull down the lock release lever (1), ad‐ just the steering wheel to the desired
angle (2) and height (3), then pull up
the lock-release lever (4) to lock the steering wheel in place. Be sure to ad‐
just the steering wheel to the desired
position before driving.
NOTICE
After adjustment, sometimes the
lock-release lever may not lock the
steering wheel.
It is not a malfunction. This occurs
when two gears engage. In this case,
adjust the steering wheel again and
then lock the steering wheel.

5-41
5
Features of your vehicle

• At this time, the Engine Start/StopButton turns to the ACC position (If
you press the Engine Start/Stop But‐ ton once more, it will turn to the ON
position).
Low key battery (for smart key
system)
• This warning message illuminates if the battery of the smart key is dis‐
charged when the Engine Start/Stop Button changes to the OFF position.
Press START button while turning
wheel (for smart key system)
• This warning message illuminates if the steering wheel does not unlock
normally when the Engine Start/Stop Button is pressed.
• It means that you should press the Engine Start/Stop Button while turn‐
ing the steering wheel right and left.
Steering wheel unlocked (for smart
key system)
• This warning message illuminates if the steering wheel does not lock
when the Engine Start/Stop Button changes to the OFF position.
Check steering wheel lock system
(for smart key system)
• This warning message illuminates if the steering wheel does not lock nor‐
mally when the Engine Start/Stop
Button changes to the OFF position.
Press brake pedal to start engine
(for smart key system)
• This warning message illuminates if the Engine Start/Stop Button
changes to the ACC position twice by pressing the button repeatedly with‐
out depressing the brake pedal.
• It means that you should depress the brake pedal to start the engine.
Key not in vehicle (for smart key
system)
• This warning message illuminates if the smart key is not in the vehicle
when you press the Engine Start/ Stop Button.
• It means that you should always have the smart key with you.
Key not detected (for smart key
system)
• This warning message illuminates if the smart key is not detected when
you press the Engine Start/Stop But‐
ton.
Press start button again (for smart
key system)
• This warning message illuminates if you cannot operate the Engine Start/
Stop Button when there is a problem with the Engine Start/Stop Button
system.
• It means that you could start the en‐ gine by pressing the Engine Start/
Stop Button once more.
• If the warning illuminates each time you press the Engine Start/Stop But‐ton, we recommend that you have
the vehicle inspected by an author‐
ized Kia dealer.
Press start button with key (for
smart key system)
• This warning message illuminates if you press the Engine Start/Stop But‐
ton while the warning message L

• Inclined roads
• A vehicle loaded with longer or widercargo compared to the vehicle
• Diagonal parking space
• Heavy snow or rain
• Near a circular pillar or narrow pillar, or a pillar surrounded by objects suchas fire extinguisher, etc.
• The sensor is positioned incorrectly by an impact to the bumper
• Bumpy roads
• A vehicle equipped with a snow chain or spare tire
• Tire pressure lower or higher than the standard tire pressure
• A trailer connected to the vehicle
• Slippery or uneven road
• Big vehicles such as buses or trucks parked
• Sensor covered with foreign matter, such as snow or water
• Moisture frozen on the sensor
• A motorcycle or bicycle parked
• A obstacle such as a trash can, bicy‐ cle, shopping cart, etc. is near
• Heavy wind • Wheel changed to an unauthorized
size
• A problem with the wheel alignment
• An accessory installed on the detec‐ tive area the of sensors (such as
number plate holder)
• Vehicle leaned severely to one side
• Strong sunlight or very cold weather
• Ultrasonic interference from other vehicle's. Such as horn sounds of oth‐
er vehicles, motorcycle's engine noise,
air brake noise of heavy vehicles and
with the other vehicle's parking assist
system working.
WARNING
Do not use the Smart Parking AssistSystem in the following conditionsfor unexpected results may occurand cause a serious accident.
(Continued)
(Continued)
0+'-
1.Parking on inclinesThe driver must apply the accel‐erator and brake pedal whenparking on inclines. If the driveris unfamiliar with applying theaccelerator and brake pedal, avehicle accident may occur.
(Continued)

5-97
5
Features of your vehicle

Steering wheel audio controls (if
equipped)
5ZQF
"5ZQF
#
5ZQF
%5ZQF
$
5ZQF
&0+'-5ZQF
'
The steering wheel may incorporate
audio control buttons.
CAUTION
Do not operate audio remote controlbuttons simultaneously.
VOLUME (+/-) (1)
• çress the lever upward (+) to increase
the volume.
• çress the lever downward (-) to de‐ crease the volume.
SEEK/PRESET (/) (2)
The êEEK/çéEêET lever has differentfunctions based on the system mode.
For the following functions the lever
should be pressed for 0.8 seconds or more.
éADIO mode
It will function as the AUTO êEEK select
button.
CD/UêB/içod® mode
It will function as the FF/éEW button.
If the êEEK/çéEêET button is pressed
for less than 0.8 seconds, it will work as follows in each mode.
éADIO mode
It will function as the çéEêET êTATION
buttons.
CD/UêB/içod® mode
It will function as TéACK Uç/DOWN
button.
MODE () (3)
çress the button to change audio
source. FM
AM CD UêB/içod ®
AUX
MY MUêIC Bluetooth ®
Wireless Tech‐
nology audio
MUTE () (4)
• çress the button to mute the sound.
• çress the button to turn off the mi‐ crophone during a telephone call.
Detailed information for audio control
buttons are described in L

Phone mode (if equipped)
Making a call using the Steering
wheel controls
❈The actual features in the vehicle
may differ from the illustration.
1. Mutes the microphone during a call.
2. çress the button to change audio
source. (Without éDê) FM
AM CD UêB (içod ®
) AUX My Music BT Audio.
(With éDê) FM1
FM2 FMA AM AMA
CD UêB (içod ®
) AUX My
Music BT Audio.
3. éaises or lowers speaker volume.
4. çlaces and transfers calls. • Check call history and making call
- êhortly press the
button
on the steering wheel controls.
- The call history list will be dis‐ played on the screen.
- çress the
button again to
connect a call to the selected number.
• éedialing the most recently called number- çress and hold the
button
on the steering wheel controls.
- The most recently called num‐ ber is redialed.
5. Ends calls or cancels functions.
6. Activates voice recognition.
MENU: Phone (Type A-1)
çress the button to display
three menus (Call History, çhone Book,
çhone êetup).
History: 1

MENU: Bluetooth® Wireless
Technology Audio
Using Bluetooth® Wireless Technology
Audio Mode
çlaying/çausing Bluetooth® WirelessTechnology Audio
Once a Bluetooth ®
Wireless Technology
device is connected, the mode will au‐
tomatically start.
While playing, press the [
II] button to
pause and press [II] button to play.
The play/pause feature may operate
differently depending on the mobile phone.
Changing Files
çress the [êEEK TéACK] button to
move to the previous or next file.
êetting Connection
If a Bluetooth ®
Wireless Technology de‐
vice has not been connected, press the
[êETUç] button [çhone] button to
display the Bluetooth ®
Wireless Tech‐
nology connection screen.
It is possible to use the pair phone, con‐
nect/disconnect and delete features
from your Bluetooth ®
Wireless Tech‐
nology phone.
If music is not yet playing from your
mobile device after converting to Blue‐
tooth ®
Wireless Technology Audio
mode, pressing the play button once
may start playing the mode. Check to
see that music is playing from the
Bluetooth ®
Wireless Technology device
after converting to Bluetooth ®
Wireless
Technology Audio Mode.
Phone Mode
Making a call using the Steering
wheel controls
❈ The actual features in the vehicle
may differ from the illustration.
1. Mutes the audio volume.
2. çress the button to change audio
source. FM
AM CD UêB (içod ®
) AUX My Music BT Audio.
(For éDê Model) FM1
FM2 FMA AM ➟
AMA CD UêB (içod ®
) AUX My Music BT Audio.
3. Used to control volume.
4. When pressed shortly

6-79
6
Audio system

ENGINE START/STOP BUTTON
Illuminated engine start/stop
button
Whenever the front door is opened, the
engine start/stop button will illuminate for your convenience. The light will go
off after about 30 seconds when the
door is closed. It will also go off imme‐ diately when the engine start/stop but‐
ton is ON position.
Engine start/stop button
position
OFF
To turn off the hybrid sys‐ tem (START/RUN position)
or vehicle power (ON posi‐ tion), press the engine start/stop button with the
shift lever in the P (Park) position. When you press the engine start/stop
button without the shift lever in the P
(Park) position, the engine start/stop button will not change to the OFF posi‐
tion but to the ACC position.
Vehicles equipped with anti-theftsteering column lock
The steering wheel locks when the en‐ gine start/stop button is in the OFF po‐
sition to protect you against theft. It locks when the door is opened.
If the steering wheel is not locked prop‐
erly when you open the driver's door, the warning chime will sound. Try lock‐
ing the steering wheel again. If the
problem is not solved, we recommend that the system be checked by an au‐
thorized Kia dealer.
/PU
JMMVNJOBUFE
In addition, if the engine start/stop but‐
ton is in the OFF position after the driv‐ er's door is opened, the steering wheel
will not lock and the warning chime will
sound. In such a situation, close the door. Then the steering wheel will lock
and the warning chime will stop.
NOTICE
If the steering wheel doesn't unlock
properly, the engine start/stop but‐
ton will not work. Press the engine
start/stop button while turning the
steering wheel right and left to re‐
lease the tension.
CAUTION
You are able to turn off the hybridsystem (START/RUN) or vehicle pow‐er (ON), only when the vehicle is notin motion. In an emergency situationwhile the vehicle is in motion, youare able to turn the hybrid systemoff and to the ACC position by press‐ing the engine start/stop button for
(Continued)
Driving your vehicle
7-06

(Continued)
more than 2 seconds or 3 times suc‐cessively within 3 seconds. If the ve‐hicle is still moving, you can restartthe hybrid system without depress‐ing the brake pedal by pressing theengine start/stop button with theshift lever in the N (Neutral) position.
ACC (Accessory)
Press the engine start/stopbutton while it is in the OFF
position without depressing the brake pedal.
The steering wheel unlocks (if equipped
with anti-theft steering column lock) and electrical accessories are opera‐
tional.
If the engine start/stop button is in the
ACC position for more than 1 hour, the button is turned off automatically to
prevent battery discharge.
"NCFS
ON
Press the engine start/stop
button while it is in the ACC position without depressingthe brake pedal.
3FEEJTI
PSBOHF
The warning lights can be checked be‐
fore the hybrid system is started. Do not leave the hybrid system start/stop
button in the ON position for a long
time. The battery may discharge, be‐ cause the engine is not running.
START/RUN
To start the hybrid system,depress the brake pedal and
press the engine start/stop button with the shift lever in the P (Park) or the N
(Neutral) position. For your safety, start the hybrid system with the shift
lever in the P (Park) position.
NOTICE
If you press the engine start/stop
button without depressing the brake
pedal for automatic transaxle vehi‐
cles, the hybrid system will not start
and the engine start/stop button
changes as follows:
OFF ACC ON OFF or ACC
/PU
JMMVNJOBUFE
NOTICE
If you leave the engine start/stop
button in the ACC or ON position for
a long time, the battery will dis‐
charge.
WARNING
•Never press the engine start/stopbutton while the vehicle is in mo‐tion. This would result in loss of di‐rectional control and braking func‐tion, which could cause an acci‐dent.
•The anti-theft steering columnlock (if equipped) is not a substi‐tute for the parking brake. Beforeleaving the driver's seat, alwaysmake sure the shift lever is engag‐ed in P (Park), set the parkingbrake fully and shut the engineoff. Unexpected and sudden vehi‐cle movement may occur if theseprecautions are not taken.
(Continued)

7-07
7
Driving your vehicle

Shift-lock override
If the shift lever cannot be moved from
the P (Park) position into R (Reverse) position with the brake pedal de‐
pressed, continue depressing the brake,
then do the following: 1. Place the engine start/stop button switch in the LOCK/OFF position.
2. Apply the parking brake.
3. Carefully remove the cap (1) cover‐ ing the shift-lock release access
hole.
4. Insert a tool (e.g. flathead screw‐ driver) into the access hole andpress down on the tool.
5. Move the shift lever.
6. Remove the tool from the shift- lock override access hole then in‐
stall the cap.
7. We recommend that the system be inspected by an authorized Kia
dealer.
Good driving practices
• Never move the shift lever from P (Park) or N (Neutral) to any other po‐
sition with the accelerator pedal de‐ pressed. • Never move the shift lever into P
(Park) when the vehicle is in motion.
• Be sure the vehicle is completely stopped before you attempt to shift
into R (Reverse) or D (Drive).
• Never take the vehicle out of gear and coast down a hill. This may beextremely hazardous. Always leave
the vehicle in gear when moving.
• Do not "ride" the brakes. This can cause them to overheat and malfunc‐
tion. Instead, when you are driving
down a long hill, slow down and shift to a lower gear. When you do this,
engine braking will help slow down
the vehicle.
• Slow down before shifting to a lower gear. Otherwise, the lower gear maynot be engaged.
• Always use the parking brake. Do not depend on placing the transaxle in P
(Park) to keep the vehicle from mov‐
ing. • Exercise extreme caution when driv‐
ing on a slippery surface. Be especial‐ly careful when braking, accelerating
or shifting gears. On a slippery sur‐
face, an abrupt change in vehicle
speed can cause the drive wheels to
lose traction and the vehicle to go out of control.
• Optimum vehicle performance and economy is obtained by smoothly de‐
pressing and releasing the accelera‐
tor pedal.
WARNING
•Always buckle-up! In a collision, anunbelted occupant is significantlymore likely to be seriously injuredor killed than a properly belted oc‐cupant.
•Avoid high speeds when corneringor turning.
•Do not make quick steering wheelmovements, such as sharp lanechanges or fast, sharp turns.
•The risk of rollover is greatly in‐creased if you lose control of yourvehicle at highway speeds.
(Continued)

7-15
7
Driving your vehicle

The ESC indicator light blinks whenever
ESC is operating or illuminates when ESC fails to operate.
ESC OFF indicator light comes on when
the ESC is turned off with the button.
CAUTION
Driving with varying tire or wheelsizes may cause the ESC system tomalfunction. When replacing tires,make sure they are the same size asyour original tires.
WARNING
The Electronic Stability Control sys‐tem is only a driving aid; use precau‐tions for safe driving by slowingdown on curved, snowy, or icy roads.Drive slowly and don’t attempt toaccelerate whenever the ESC indica‐tor light is blinking, or when the roadsurface is slippery.
ESC OFF usage
When driving
• ESC should be turned on for daily driving whenever possible. • To turn ESC off while driving, press
the ESC OFF button while driving on aflat road surface.
WARNING
Never press the ESC OFF buttonwhile ESC is operating (ESC indicatorlight blinks).If ESC is turned off while ESC is op‐erating, the vehicle may slip out ofcontrol.
NOTICE
•When operating the vehicle on a
dynamometer, ensure that the
ESC is turned off by pressing the
ESC OFF button for more than 3
seconds (ESC OFF light illumina‐
ted). If the ESC is left on, it may
prevent the vehicle speed from in‐
creasing, and result in false diag‐
nosis.
•Turning the ESC off does not af‐
fect ABS or brake system opera‐
tion.
Vehicle stability management
(VSM) (if equipped)
This system provides further enhance‐ments to vehicle stability and steering
responses when a vehicle is driving on a
slippery road or a vehicle detected changes in coefficient of friction be‐
tween right wheels and left wheels
when braking.
VSM operation
When the VSM is in operation, • ESC (Electronic Stability Control) ()
light will blink.
• The steering wheel may be control‐ led.
When the vehicle stability management is operating properly, you can feel a
slight pulsation in the vehicle. This is
only the effect of brake control and in‐ dicates nothing unusual.
The VSM does not operate when:
• Driving on bank road such as gradient or incline
• Driving rearward
• ESC OFF indicator light (
) remains
on the instrument cluster

7-33
7
Driving your vehicle