ABS KIA PICANTO 2018 Owner's Manual

Side repeater lamp (LED type)
bulb Replacement
Iý the Side repeater lamp (1) does not
operate, have your vehicle checked by a proýessional workshop. Kia recom‐
mends to visit an authorized Kia dealer/
service partner.
Side repeater lamp (bulb type)
bulb Replacement
1. Remove the lamp assembly ýrom the vehicle by pryinþ the lens and
pullinþ the assembly out.
2. Disconnect the bulb electrical con‐ nector.
3. Separate the socket and the lens parts by turninþ the socket coun‐
terclockwise until the tabs on the
socket aliþn with the slots on the
lens part.
4. Remove the bulb by pullinþ it straiþht out.
5. Insert a new bulb in the socket. 6. Reassemble the socket and the
lens part.
7. Connect the bulb electrical connec‐ tor.
8. Reinstall the lamp assembly to the body oý the vehicle.
Stop and tail lamp bulb
replacement
1. æpen the tailþate.
2. Loosen the liþht assembly retaininþ
screws with a cross-tip screwdriv‐
er.

8-93
8
Maintenance

3. Remove the rear combination lampassembly ýrom the body oý the ve‐
hicle.
4. Disconnect the rear combination lamp connector.
5. Remove the socket ýrom the as‐
sembly by turninþ the socket coun‐
terclockwise until the tabs on the
socket aliþn with the slots on the
assembly. 6. Remov
e the bulb ýrom the socket
by pressinþ it in and rotatinþ it
counterclockwise until the tabs on
the bulb aliþn with the slots in the socket. çull the bulb out oý the
socket.
7. Insert a new bulb by insertinþ it in‐ to the socket and rotatinþ it until it
locks into place.
8. Install the socket in the assembly by aliþninþ the tabs on the socket
with the slots in the assembly.
çush the socket into the assembly
and turn the socket clockwise.
9. Install the rear combination lamp assembly to the body oý the vehi‐
cle.
Maintenance
8-94

Rear turn siþnal lamp bulb
replacement
1. æpen the tailþate.
2. Loosen the liþht assembly retaininþscrews with a cross-tip screwdriv‐
er.
3. Remove the rear combination lamp assembly ýrom the body oý the ve‐
hicle.
4. Disconnect the rear combination lamp connector.
5. Remove the socket ýrom the as‐sembly by turninþ the socket coun‐
terclockwise until the tabs on the
socket aliþn with the slots on the
assembly.
6. Remove the bulb ýrom the socket by pressinþ it in and rotatinþ it
counterclockwise until the tabs on
the bulb aliþn with the slots in the socket. çull the bulb out oý the
socket.
7. Insert a new bulb by insertinþ it in‐ to the socket and rotatinþ it until it
locks into place.
8. Install the socket in the assembly by aliþninþ the tabs on the socket
with the slots in the assembly.
çush the socket into the assembly
and turn the socket clockwise.
9. Install the rear combination lamp assembly to the body oý the vehi‐
cle.

8-95
8
Maintenance

License plate lamp bulb
replacement
1. Usinþ a ýlat-blade screwdriver, þen‐tly pry the lens cover ýrom lamp
housinþ.
2. Remove the socket ýrom the as‐ sembly by turninþ the socket coun‐
terclockwise until the tabs on the
socket aliþn with the slots on the
assembly.
3. Remove the bulb ýrom bulb-socket by pullinþ it out.
4. Insert a new bulb by insertinþ it in‐ to the bulb-socket. 5. Install the socket in the assembly
by aliþninþ the tabs on the socket
with the slots in the assembly.
çush the socket into the assembly
and turn the socket clockwise.
6. Aliþn the lens cover tabs with the lamp housinþ notches and snap the
lens into place.
Map lamp bulb replacement (iý
equipped)
WARNING
Prior to workinþ on the Interiorlamps, ensure that the L

1. Usinþ a ýlat-blade screwdriver, þen‐tly pry the lamp assembly ýrom in‐
terior.
2. Remove the bulb by pullinþ it straiþht out.
3. Install a new bulb in the socket.
4. Install the lamp assembly to interi‐ or.
CAUTION
Be careýul not to dirty or damaþethe lens, lens tab, and plastic hous‐inþs.
Tailþate room lamp bulb
replacement
1. Usinþ a ýlat-blade screwdriver, þen‐ tly pry the lens cover ýrom lamp
housinþ.
2. Remove the bulb by pullinþ it straiþht out.
3. Install a new bulb in the socket.
4. Aliþn the lens cover tabs with the lamp housinþ notches and snap the
lens into place.
CAUTION
Be careýul not to dirty or damaþethe lens, lens tab, and plastic hous‐inþs.
Maintenance
8-100

Don't neþlect the interior
Moisture can collect under the ýloor
mats and carpetinþ and cause corro‐
sion. Check under the mats periodically to be sure the carpetinþ is dry. Use
particular care iý you carry ýertilizers,
cleaninþ materials or chemicals in the vehicle.
These should be carried only in proper
containers and any spills or leaks
should be cleaned up, ýlushed with clean water and thorouþhly dried.
Interior care
Interior þeneral precautions
çrevent chemicals such as perýume,
cosmetic oil, sun cream, hand cleaner, and air ýreshener ýrom contactinþ the
interior parts because they may cause
damaþe or discoloration. Iý they do con‐ tact the interior parts, wipe them oýý
immediately. Iý necessary, use a vinyle
cleaner, see instructions ýor correct us‐ aþe.
CAUTION
Never allow water or other liquids tocome in contact with electrical/elec‐
(Continued)
(Continued)
tronic components inside the vehicleas this may damaþe them.
CAUTION
When cleaninþ leather products(steerinþ wheel, seats etc.), useneutral deterþents or low alcoholcontent solutions. Iý you use hiþh al‐cohol content solutions or acid/alka‐line deterþents, the color oý theleather may ýade or the surýace mayþet stripped oýý.
Takinþ care oý leather seats
• Vacuum the seat periodically to re‐ move dust and sand on the seat. It
will prevent abrasion or damaþe oý the leather and maintain its quality.
• Wipe the natural leather seat cover oýten with dry or soýt cloth.
• Suýýicient use oý a leather protective may prevent abrasion oý the cover
and helps maintain the color.
Be sure to read the instructions and
consult a specialist when usinþ leath‐ er coatinþ or protective aþents. • Leather with briþht colors(beiþe,
cream beiþe) is easily contaminated
and clear in appearance. Clean the
seats ýrequently.
• Avoid wipinþ with wet cloth. It may cause the surýace to crack.
Cleaninþ the leather seats
• Remove all contaminations instantly.Reýer to instructions below ýor re‐
moval oý each contaminant.
• Cosmetic products(sunscreen, ýoun‐ dation, etc.)- Apply cleansinþ cream on a cloth and wipe the contaminated point.
Wipe oýý the cream with a wet cloth and remove water with a dry
cloth.
• Beveraþes(coýýee, soýt drink, etc.) - Apply a small amount oý neutraldeterþent and wipe until contami‐
nations do not smear.
• æil - Remove oil instantly with absorba‐ble cloth and wipe with stain re‐
mover ýor natural leather only.
• Chewinþ þum - Harden the þum with ice and re‐move þradually.
Maintenance
8-112

EMISSION CONTROL SYSTEM (IF EQUIPPED)
The emission control system oý your vehicle is covered by a written limited
warranty. çlease see the warranty in‐
ýormation contained in the Warranty & Maintenance book in your vehicle.
Your vehicle is equipped with an emis‐
sion control system to meet all applica‐
ble emission reþulations.
There are three emission control sys‐ tems, as ýollows. 1. Crankcase emission control system
2. Evaporative emission control sys‐ tem
3. Exhaust emission control system

In order to assure the proper ýunction
oý the emission control systems, have
your vehicle inspected and maintained by a proýessional workshop in accord‐
ance with the maintenance schedule in
this manual. Kia recommends to visit an
authorized Kia dealer/service partner.
Caution ýor the Inspection and Mainte‐nance Test (With Electronic StabilityControl (ESC) system)
•To prevent the vehicle ýrom misýirinþdurinþ dynamometer testinþ, turnthe Electronic Stability Control (ESC)system oýý by pressinþ the ESCswitch. •
Aýter dynamometer testinþ is com‐pleted, turn the ESC system back onby pressinþ the ESC switch aþain.
1. Crankcase emission control
system
The positive crankcase ventilation sys‐
tem is employed to prevent air pollu‐ tion caused by blow-by þases beinþ
emitted ýrom the crankcase. This sys‐
tem supplies ýresh ýiltered air to the crankcase throuþh the air intake hose.
Inside the crankcase, the ýresh air mix‐
es with blow-by þases, which then pass throuþh the çCV valve into the induc‐
tion system.
2. Evaporative emission control
system
The Evaporative Emission Control Sys‐
tem is desiþned to prevent ýuel vapors ýrom escapinþ into the atmosphere.
Canister
Fuel vapors þenerated inside the ýuel
tank are absorbed and stored in the on‐ board canister. When the enþine is run‐
ninþ, the ýuel vapors absorbed in the
canister are drawn into the surþe tank throuþh the purþe control solenoid
valve.
Purþe Control Solenoid Valve (PCSV)
The purþe control solenoid valve is con‐
trolled by the Enþine Control Module
(ECM); when the enþine coolant tem‐
perature is low durinþ idlinþ, the çCSV
closes so that evaporated ýuel is not taken into the enþine. Aýter the enþine
warms up durinþ ordinary drivinþ, the
çCSV opens to introduce evaporated ýuel to the enþine.
3. Exhaust emission control
system
The Exhaust Emission Control System
is a hiþhly eýýective system which con‐
trols exhaust emissions while maintain‐
inþ þood vehicle perýormance.
Vehicle modiýications
This vehicle should not be modiýied.
Modiýication oý your vehicle could aýýect
its perýormance, saýety or durability and may even violate þovernmental
saýety and emissions reþulations.
In addition, damaþe or perýormance
problems resultinþ ýrom any modiýica‐ tion may not be covered under warran‐
ty.
Maintenance
8-114

Battery recharþinþ..................................................... 8-55
For best battery service............................................ 8-53
Reset items................................................................. 8-55
Beýore drivinþ.................................................................. 6-04
Beýore enterinþ vehicle..............................................6-04
Beýore startinþ............................................................6-04
Necessary inspections............................................... 6-04
Brake system.................................................................. 6-29
Anti-lock brake system (ABS).................................. 6-32
Electronic Stability Control (ESC)............................. 6-34
ESS : Emerþency Stop Siþnal.................................... 6-38
Good brakinþ practices.............................................. 6-39
Hill-start assist control (HAC).................................. 6-37
çarkinþ brake.............................................................. 6-30
çower brakes.............................................................. 6-29
Vehicle stability manaþement (VSM)...................... 6-37
Brake/Clutch ýluid........................................................... 8-40
Checkinþ the brake/clutch ýluid level.......................8-40
Bulb wattaþe................................................................... 9-04
C
Child r estraint system (CRS)......................................... 3-27
Installinþ a Child Restraint System (CRS)............... 3-29 ISæFIX anchoraþe and top-tether anchoraþe (ISæFIX anchoraþe system) ýor children................ 3-30
Selectinþ a Child Restraint System (CRS)...............3-27 Climate control air ýilter.......................................4-94,8-49
Filter inspection.......................................................... 8-49
Cruise control system.................................................... 6-41
Cruise control switch..................................................6-42
To cancel cruise control............................................. 6-45
To decrease the cruisinþ speed................................ 6-44
To increase cruise control set speed....................... 6-44
To resume cruisinþ speed at more than ap‐proximately 30 km/h (20 mph)............................... 6-46
To set cruise control speed....................................... 6-42
To temporarily accelerate with the cruise control on.................................................................... 6-45
To turn cruise control oýý.......................................... 6-46
D
Declaration oý conýormity................................... 5-33,9-20 ANATEL ýor Brazil....................................................... 5-35
CE ýor EU...................................................................... 5-33
IFETEL........................................................................... 5-35
NCC ýor Taiwan........................................................... 5-34
Deýroster.......................................................................... 4-86
Rear window deýroster............................................. 4-86
Dimensions....................................................................... 9-03
Door locks......................................................................... 4-16
Child-protector rear door lock..................................4-19
Impact sensinþ door unlock system........................ 4-19
Alphabetical index
I-2 Alphabetical index