check engine KIA QUORIS 2014 Repair Manual
[x] Cancel search | Manufacturer: KIA, Model Year: 2014, Model line: QUORIS, Model: KIA QUORIS 2014Pages: 486, PDF Size: 31.74 MB
Page 406 of 486

Maintenance
30
7
POWER STEERING FLUID
Checking the power steering
fluid level
With the vehicle on level ground,
check the fluid level in the power
steering reservoir periodically. The
fluid should be between MAX and
MIN marks on the side of the gauge
at the normal temperature.
Before adding power steering fluid, thoroughly clean the area around the
reservoir cap to prevent power steer-ing fluid contamination.
If the level is low, add fluid to the
MAX level.
✽✽ NOTICE
Check that the fluid level is in the
"HOT" range on the gauge. If the
fluid is cold, check that it is in the
"COLD" range.
In the event the power steering sys- tem requires frequent additions of
fluid, we recommend that the system
be inspected by an authorized Kia
dealer.
Use only the specified power steer- ing fluid. (Refer to "Recommendedlubricants or capacities" in section8.)
Checking the power steering hose
Check the connections for oil leaks,
damage and twists in the power
steering hose before driving.OBH078022
CAUTION
To avoid damage to the power steering pump, do not operatethe vehicle for prolonged peri- ods with a low power steeringfluid level.
Never start the engine when the reservoir tank is empty.
When adding fluid, be careful that dirt does not get into thetank.
Too little fluid can result in increased steering effortand/or noise from the powersteering system.
(Continued)
(Continued) The use of the non-specified fluid could reduce the effective-ness of the power steering sys-tem and cause damage to it.
Page 430 of 486

Maintenance
54
7
FUSES
A vehicle’s electrical system is pro-
tected from electrical overload dam-
age by fuses.
This vehicle has 2 fuse panels, one
located in the driver’s side panel bol-
ster, another is in the engine com-
partment.
If any of your vehicle’s lights, acces-
sories, or controls do not work, check
the appropriate circuit fuse. If a fuse
has blown, the element inside thefuse will be melted.
If the electrical system does not
work, first check the driver’s sidefuse panel.
Before replacing a blown fuse, dis-
connect the negative battery cable.
Always replace a blown fuse with
one of the same rating.
If the replacement fuse blows, this
indicates an electrical problem. Avoid
using the system involved and we
recommend that you consult an
authorized Kia dealer.
Three kinds of fuses are used: blade
type for lower amperage rating, car-
tridge type, and fusible link for higher
amperage ratings. ✽
✽
NOTICE
The actual fuse/relay panel label
may differ from equipped items.
WARNING - Fuse replace-
ment
Never replace a fuse with any- thing but another fuse of the same rating.
A higher capacity fuse could cause damage and possibly a
fire.
Never install a wire or alu- minum foil instead of the prop-
er fuse even as a temporary
repair. It may cause extensive
wiring damage and a possible
fire.
CAUTION
Do not use a screwdriver or any
other metal object to removefuses because it may cause a short circuit and damage thesystem.
OKH072054L
Normal
Normal
■
Blade type
■ Cartridge type
■ Multi fuse type Blown
Blown
Normal Blown
Normal Blown
Page 431 of 486

755
Maintenance
Instrument panel fuse replace- ment
1. Turn the ignition switch and allother switches off.
2. Open the fuse panel cover. 3. Pull the suspected fuse straight
out. Use the removal tool provided
in the engine compartment fusepanel.
4. Check the removed fuse; replace it if it is blown.
5. Push in a new fuse of the same rating, and make sure it fits tightly
in the clips.
If it fits loosely, we recommend that
you consult an authorized Kia dealer.
If you do not have a spare, use a
fuse of the same rating from a circuit
you may not need for operating the
vehicle, such as the cigarette lighter
fuse.CAUTION
When replacing a blown fuse or relay with a new one, makesure the new fuse or relay fitstightly into the clips Theincomplete fastening fuse or relay may cause the vehiclewiring and electric systemsdamage and a possible fire.
Do not remove fuses, relays and terminals fastened withbolts or nuts. The fuses, relaysand terminals may be fas-tened incompletely, and it maycause a possible fire. If fuses, relays and terminals fastenedwith bolts or nuts are blown,we recommend that you con- sult with an authorized Kiadealer.
Do not input any other objects except fuses or relays intofuse/relay terminals such as a driver or wiring. It may causecontact failure and systemmalfunction.
OKH072019
■ Drive side panel
OKH072020
Page 432 of 486

Maintenance
56
7
If the headlights or other electrical
components do not work and the
fuses are OK, check the fuse panel
in the engine compartment. If a fuse
is blown, it must be replaced.Fuse switch
Always, put the fuse switch at the ON position.
If you move the switch to the OFF position, some items such as audio
and digital clock must be reset and
transmitter (or smart key) may not
work properly.
CAUTION
Always place the fuse switch
in the ON position while driv-ing the vehicle.
Do not move the transporta- tion fuse switch repeatedly.The fuse switch may be wornout.
OKH072021
Page 433 of 486

757
Maintenance
Engine compartment fuse replacement
1. Turn the ignition switch and allother switches off.
2. Remove the fuse panel cover by pressing the tab and pulling the
cover up. 3.Check the removed fuse; replace it
if it is blown. To remove or insert
the fuse, use the fuse puller in the
engine compartment fuse panel.
4.Push in a new fuse of the same rat- ing, and make sure it fits tightly in
the clips.
If it fits loosely, we recommend that
you consult an authorized Kia deal-
er.Main fuse
If the main fuse is blown, it must be
removed as follows:
1. Turn off the engine.
2. Disconnect the negative battery cable.
3. Remove the nuts shown in the pic- ture above.
4. Replace the fuse with a new one of the same rating.
5. Reinstall in the reverse order of removal.
CAUTION
After checking the fuse panel in
the engine compartment,securely install the fuse panel cover. If not, electrical failuresmay occur from water contact.OBH078025OKH072022
OKH072023
Page 463 of 486

787
Maintenance
Canister
Fuel vapors generated inside the fuel tank are absorbed and stored in the
onboard canister. When the engine is
running, the fuel vapors absorbed in
the canister are drawn into the surgetank through the purge control sole-
noid valve.
Purge Control Solenoid Valve(PCSV)
The purge control solenoid valve is
controlled by the Engine Control
Module (ECM); when the engine
coolant temperature is low during
idling, the PCSV closes so that evapo-
rated fuel is not taken into the engine.
After the engine warms-up during ordi-
nary driving, the PCSV opens to intro-
duce evaporated fuel to the engine. 3. Exhaust emission control
system
The Exhaust Emission Control
System is a highly effective system
which controls exhaust emissions
while maintaining good vehicle per-
formance.
Vehicle modifications
This vehicle should not be modified.
Modification of your vehicle could
affect its performance, safety or
durability and may even violate gov-
ernmental safety and emissions reg-
ulations.
In addition, damage or performance
problems resulting from any modifi-
cation may not be covered under
warranty.
If you use unauthorized electronic devices, it may cause the vehicle to
operate abnormally, wire damage,
battery discharge and fire. For your
safety, do not use unauthorized
electronic devices.
Engine exhaust gas precautions
(carbon monoxide)
Carbon monoxide can be present with other exhaust fumes.
Therefore, if you smell exhaust
fumes of any kind inside your vehi-
cle, have it inspected and repaired
immediately. If you ever suspect
exhaust fumes are coming into
your vehicle, drive it only with all
the windows fully open. Have your
vehicle checked and repaired
immediately.
WARNING - Exhaust
Engine exhaust gases contain
carbon monoxide (CO). Though
colorless and odorless, it is
dangerous and could be lethal if
inhaled. Follow the instructions
on this page to avoid CO poi-soning.
Page 473 of 486

Specifications & Consumer information
8
8
Recommended SAE viscosity
number Engine oil viscosity (thickness) has
an effect on fuel economy and cold
weather operating (engine start and
engine oil flowability). Lower viscosi-
ty engine oils can provide better fuel
economy and cold weather perform-
ance, however, higher viscosity
engine oils are required for satisfac-
tory lubrication in hot weather.Using oils of any viscosity other thanthose recommended could result in
engine damage. When choosing an oil, consider the
range of temperature your vehicle will
be operated in before the next oil
change. Proceed to select the recom-
mended oil viscosity from the chart.
CAUTION
Always be sure to clean the area
around any filler plug, drain
plug, or dipstick before check-
ing or draining any lubricant.
This is especially important in
dusty or sandy areas and when
the vehicle is used on unpaved
roads. Cleaning the plug and
dipstick areas will prevent dirt
and grit from entering the
engine and other mechanisms
that could be damaged.
Temperature Range for SAE Viscosity Numbers
Temperature
Gasoline
Engine Oil * 1°C
(°F)-30 -20 -10 0 10 20 30 40 50 -10 0 20 40 60 80 100 120
*1
: For better fuel economy, it is recommended to use the engine oil of a viscosity grade SAE
5W-20 (API SM / ILSAC GF-4). However, if the engine oil is not available in your country,
select the proper engine oil using the engine oil viscosity chart.
* 2
: In Middle East, do not use the engine oil of viscosity grade SAE 5W-20.
20W-50
10W-30
15W-40
5W-20, 5W-30, 5W-40
Page 478 of 486

I3
Index
Blind spot detection system (BSD) . . . . . . . . . . . . . . . 5-89
Bluetooth ®
Wireless Technology hands-free . . . . . . . 4-162
Bottle holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-151
Brake system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31 Anti-lock brake system (ABS) . . . . . . . . . . . . . . . . . . 5-34
Auto hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-42
AVSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-54
Electric parking brake (EPB) . . . . . . . . . . . . . . . . . . . 5-36
Electronic stability control (ESC) . . . . . . . . . . . . . . . 5-46
Hill-start assist control (HAC) . . . . . . . . . . . . . . . . . . 5-51
Power brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31
Vehicle stability management. . . . . . . . . . . . . . . . . . . 5-50
Brakes/clutch fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-29
Bulb replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-74
Bulb wattage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
Button start/stop, see engine start/stop button . . . . . . . . 5-6
Camera (Rear view) . . . . . . . . . . . . . . . . . . . . . . . . . . 4-104
Capacities (Lubricants) . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
Care Exterior care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-79
Interior care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-84
Tire care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-43
Center console storage . . . . . . . . . . . . . . . . . . . . . . . . 4-146
Central door lock/unlock switch. . . . . . . . . . . . . . . . . . 4-17 Certification label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Chains
Tire chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-102
Checking tire inflation pressure . . . . . . . . . . . . . . . . . . 7-44
Child restraint system . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32 ISOFIX system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39
Seat belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35
Tether anchor system . . . . . . . . . . . . . . . . . . . . . . . . . 3-38
Child-protector rear door lock . . . . . . . . . . . . . . . . . . . 4-19
Cigarette lighter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-150
Climate control air filter . . . . . . . . . . . . . . . . . . . . . . . . 7-35
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-157
Clothes hanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-157
Cluster Settings (Type B) . . . . . . . . . . . . . . . . . . . . . . . 4-66
Combined instrument, see instrument cluster . . . . . . . 4-49
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-26
Cooling fluid, see engine coolant . . . . . . . . . . . . . . . . . 7-26
Crankcase emission control system . . . . . . . . . . . . . . . 7-86
Cruise control system . . . . . . . . . . . . . . . . . . . . . . . . . . 5-65
Cup holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-151
Curtain air bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-55
Dashboard illumination, see instrument panel illumination . . 4-50
Dashboard, see instrument cluster . . . . . . . . . . . . . . . . 4-49
Daytime running light . . . . . . . . . . . . . . . . . . . . . . . . . 4-110
C
D